This is the minimum fixmap interface expected to be implemented by
architectures supporting highmem.

We have a second level page table already allocated and covering
0xfff00000-0xffffffff because the exception vector page is located
at 0xffff0000, and various cache tricks already use some entries above
0xffff0000.  Therefore the PTEs covering 0xfff00000-0xfffeffff are free
to be used.

However the XScale cache flushing code already uses virtual addresses
between 0xfffe0000 and 0xfffeffff.

So this reserves the 0xfff00000-0xfffdffff range for fixmap stuff.

The Documentation/arm/memory.txt information is updated accordingly,
including the information about the actual top of DMA memory mapping
region which didn't match the code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>

The current use of these macros works well when the conversion is
entirely linear.  In this case, we can be assured that the following
holds true:

	__va(p + s) - s = __va(p)

However, this is not always the case, especially when there is a
non-linear conversion (eg, when there is a 3.5GB hole in memory.)
In this case, if 's' is the size of the region (eg, PAGE_SIZE) and
'p' is the final page, the above is most definitely not true.

So, we must ensure that __va() and __pa() are only used with valid
kernel direct mapped RAM addresses.  This patch tweaks the code
to achieve this.
Tested-by: Charles Moschel <fred99@carolina.rr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This is a fix for the following crash observed in 2.6.29-rc3:
http://lkml.org/lkml/2009/1/29/150

On ARM it doesn't make sense to trace a naked function because then
mcount is called without stack and frame pointer being set up and there
is no chance to restore the lr register to the value before mcount was
called.
Reported-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Tested-by: Matthias Kaehlcke <matthias@kaehlcke.net>

Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@home.goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into s3c-fixes

Includes missed irqs.h in devices.c and mx1ads.c.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Fix build warnings due to struct i2c_board_info in <mach/platform.h>

Patch "5311/1: add core support for built in i2c bus" is causing 11 of
39 the build warnings with Kautobuild for ep93xx_defconfig on kernel
2.6.29-rc5-git4.  This patch fixes it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

gcc seems to expect that lr isn't clobbered by mcount, because for a
function starting with:

	static int func(void)
	{
		void *ra = __builtin_return_address(0);

		printk(KERN_EMERG "__builtin_return_address(0) = %pS\n", ra)

		...

the following assembler is generated by gcc 4.3.2:

	   0:   e1a0c00d        mov     ip, sp
	   4:   e92dd810        push    {r4, fp, ip, lr, pc}
	   8:   e24cb004        sub     fp, ip, #4      ; 0x4
	   c:   ebfffffe        bl      0 <mcount>
	  10:   e59f0034        ldr     r0, [pc, #52]
	  14:   e1a0100e        mov     r1, lr
	  18:   ebfffffe        bl      0 <printk>

Without this patch obviously __builtin_return_address(0) yields
func+0x10 instead of the return address of the caller.

Note this patch fixes a similar issue for the routines used with dynamic
ftrace even though this isn't currently selectable for ARM.

Cc: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Changing it do 100kHz is needed to make more devices works properly. Controlling the
TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine.
EDID readout is unaffected by this change.

[1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234Signed-off-by: Koen Kooi <koen@beagleboard.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fixes a linker error when OMAP I2C bus driver is compiled as a module:

   ERROR: "i2c_register_board_info" [arch/arm/plat-omap/i2c.ko] undefined!

The I2C utility functions used for board initialization should be always
built-in.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Acked-by: Jarkko Nikula  <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

After my OMAP3 board has been running for a while, I'm seeing weird
latency traces like this:

      sh-1574    0d.h2  153us : do_timer (tick_do_update_jiffies64)
      sh-1574    0d.h2  153us : update_wall_time (do_timer)
      sh-1574    0d.h2  153us!: omap_32k_read (update_wall_time)
      sh-1574    0d.h2 1883us : update_xtime_cache (update_wall_time)
      sh-1574    0d.h2 1883us : clocksource_get_next (update_wall_time)
      sh-1574    0d.h2 1883us+: _spin_lock_irqsave (clocksource_get_next)

and after a while:

      sh-17818   0d.h3  153us : do_timer (tick_do_update_jiffies64)
      sh-17818   0d.h3  153us : update_wall_time (do_timer)
      sh-17818   0d.h3  153us!: omap_32k_read (update_wall_time)
      sh-17818   0d.h3 1915us : update_xtime_cache (update_wall_time)
      sh-17818   0d.h3 1915us+: clocksource_get_next (update_wall_time)
      sh-17818   0d.h3 1945us : _spin_lock_irqsave (clocksource_get_next)

Turns out that sched_clock() is using cyc2ns(), which returns NTP
adjusted time. The sched_clock() frequency should not be adjusted. The
patch deletes omap_32k_ticks_to_nsecs() and rewrites sched_clock()
to do the conversion using the constant multiplier.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change the error to a warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Run sbc610 USB fixup code only on the appropriate platform.

[airlied: you shall not retype patches from other trees half asleep]
Signed-of-by: Dave Airlie <airlied@redhat.com>

commit a969e76a (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.

Fixes Fedora bug #486511.
(https://bugzilla.redhat.com/show_bug.cgi?id=486511)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ixp4xx - Fix qmgr_request_queue build failure
  crypto: api - Fix module load deadlock with fallback algorithms

There is another user of IXP4xx queue manager, fix it.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This data should be passed to the xor driver in order to initialize
the address decoding windows of the xor unit. without this patch, the
self tests of the xor will fail unless the address decoding windows were
initialized by the boot loader.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: don't allow setuid to succeed if the user does not have rt bandwidth
  sched_rt: don't start timer when rt bandwidth disabled

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: oprofile: don't set counter width from cpuid on Core2
  x86: fix init_memory_mapping() to handle small ranges

* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86 mmiotrace: fix race with release_kmmio_fault_page()
  x86 mmiotrace: improve handling of secondary faults
  x86 mmiotrace: split set_page_presence()
  x86 mmiotrace: fix save/restore page table state
  x86 mmiotrace: WARN_ONCE if dis/arming a page fails
  x86: add far read test to testmmiotrace
  x86: count errors in testmmiotrace.ko

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: Teach RCU that idle task is not quiscent state at boot

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] fix lots of ARM __devexit sillyness
  [ARM] 5417/1: Set the correct cacheid for ARMv6 CPUs with ARMv7 style MMU
  [ARM] 5416/1: Use unused address in v6_early_abort
  [ARM] 5411/1: S3C64XX: Fix EINT unmask
  [ARM] at91: fix for Atmel AT91 powersaving
  [ARM] RiscPC: Fix etherh oops

`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack.  If the store succeeeds this
corrupts r0 in pt_regs.  Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Impact: fix stuck NMIs and non-working oprofile on certain CPUs

Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.

This should fix bug #12395:

  http://bugzilla.kernel.org/show_bug.cgi?id=12395Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix failed EFI bootup in certain circumstances

Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.

It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit 155b25bc, which was
totally wrong - the "embedded" options still exists (very much so) even
on non-embedded platforms.

It's just that we don't bother with actually asking about them when
we're not embedded, we just take their default values (which is usually
'y' - the options add features that may not be worth it in a constrained
environment).
Noticed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Fix use-before-null-check in i915_irq_emit().
  drm: Avoid client deadlocks when the master disappears.
  drm: Wake up all lock waiters when the master disappears.
  drm: Don't return ERESTARTSYS to user-space.

This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

This is done by
1) Wake up lock waiters when we close the master file descriptor.
   Not when the master structure is removed, since the latter
   requires the waiters themselves to release the refcount on the
   master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
   Normally these clients will get a SIGPIPE when the X server dies,
   but clients may also spin trying to grab the DRM lock, without
   getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>

The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED
menu.  Fix by moving it to just after all of the EMBEDDED menu symbols.

Also, surround all of the EMBEDDED symbols with "if EMBEDDED"/"endif" so
that this EMBEDDED block is clearer.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>