Prefer the term "device" over "chip". Therefore, modify the relevant terms
in hal Rx return buffer manager to use "device" instead.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430165811.1377182-2-quic_periyasa@quicinc.com

Currently, in ath11k_ahb_probe(), if a failure occurs after
ath11k_ahb_ce_remap() is called, and if hw_params->ce_remap is
enabled, the CE register memory is not unmapped. So add a call to
ath11k_ahb_ce_unmap() in the error path.

This issue was identified by smatch/smatch_scripts/kchecker:

drivers/net/wireless/ath/ath11k/ahb.c:1218 ath11k_ahb_probe() warn: 'ab->mem_ce' from ioremap() not released on lines: 1218.

Since this is a rare error path with no simple way to test, and since
the change is trivial to review, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430-ce-unmap-v1-2-e468328f95d9@quicinc.com

Currently the logic that handles hw_params->ce_remap is inline code,
both for doing the remap and the unmap. An upcoming change needs to do
the unmap in a second place, so refactor the unmap logic into a
separate function. And although it is only called from one place,
refactor the remap logic as well to have functional symmetry.

No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240430-ce-unmap-v1-1-e468328f95d9@quicinc.com

Currently, hardware state is not protected across the reconfigure
operations. However, in single wiphy models, multiple radio/links is
exposed as a MAC hardware (ieee80211_hw) through the driver hardware
abstraction (ath12k_hw) layer. In such scenario, we need to protect
hardware state across the multiple radio/link at the driver hardware
abstraction (ath12k_hw) layer. Therefore, introduce a new mutex in
the ath12k_hw layer.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-4-quic_periyasa@quicinc.com

Currently, in multi wiphy models, the mac80211 hardware state is maintained
within the radio/link structure. However, in single wiphy models, the
mac80211 hardware state is needed at the hardware abstraction layer
(ath12k_hw). Therefore, move the hardware state from the radio/link
structure to the hardware abstraction layer (ath12k_hw). Additionally,
update the naming convention of the state enums to enhance clarity and
consistency.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-3-quic_periyasa@quicinc.com

Currently, in multi-wiphy models, the recovery handler access mac80211
HW from the radio/link structure. This will be incorrect for single wiphy
model, as they will hold multiple link/radio structures. To fix this,
access mac80211 HW based on the number of hardware in the SoC/chip. This
approach makes the recovery handler compatible with both multi wiphy and
single wiphy models.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240425090307.3233434-2-quic_periyasa@quicinc.com

Simplify the loop by using list_for_each_entry(). No functional changes.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://msgid.link/20240411165516.4070649-3-kvalo@kernel.org

ath.git patches for v6.10

ath12k

* debugfs support

* dfs_simulate_radar debugfs file

* disable Wireless Extensions

* suspend and hibernation support

* ACPI support

* refactoring in preparation of multi-link support

ath11k

* support hibernation (required changes in qrtr and MHI subsystems)

* ieee80211-freq-limit Device Tree property support

ath10k

* firmware-name Device Tree property support

mt76 patches for 6.10

- fixes
- mt7603 stability improvements
- mt7921 LED control
- mt7925 EHT radiotap support

Advertise support for BSS color and then once the countdown reaches 0,
call color change finish.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240422053412.2024075-8-quic_adisi@quicinc.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

In order to support color change with MLO, handle the link ID now
passed from cfg80211, adjust the code to do everything per link
and call the notifications to cfg80211 correctly.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240422053412.2024075-4-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-5-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-6-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-7-quic_adisi@quicinc.com
[squash, move API call updates to this patch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, during color change, no link id information is passed down.
In order to support color change during Multi Link Operation, it is
required to pass link id as well.
Additionally, update notification APIs to allow drivers/mac80211 to
pass the link ID.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240422053412.2024075-2-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-3-quic_adisi@quicinc.com
[squash, actually only pass 0 from mac80211]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wdev->valid_links is not cleared when upper layer disconnect from a
wdev->AP MLD. It has been observed that this would prevent offchannel
operations like remain-on-channel which would be needed for user space
operations with Public Action frame.
Clear the wdev->valid_links when STA disconnects.
Signed-off-by: Xin Deng <quic_deng@quicinc.com>
Link: https://msgid.link/20240426092501.8592-1-quic_deng@quicinc.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

struct net_device shouldn't be embedded into any structure, instead,
the owner should use the priv space to embed their state into net_device.

Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].

Un-embed the net_device from struct iwl_trans_pcie by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at iwl_trans_pcie_alloc.

The private data of net_device becomes a pointer for the struct
iwl_trans_pcie, so, it is easy to get back to the iwl_trans_pcie parent
given the net_device object.

[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://msgid.link/20240501165417.3406039-1-leitao@debian.orgSigned-off-by: Johannes Berg <johannes.berg@intel.com>

It is supported by all drivers
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add IEEE80211_RADIOTAP_EHT and IEEE80211_RADIOTAP_EHT_USIG radiotap
to fill in EHT information, such as MCS, NSS, GI and bandwidth.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce wifi LED switch control, add flow to Control a wifi
gpio pin based on the status of WIFI radio, if the pin is connected
to an LED, the LED will indicate the status of the WiFi radio.
Signed-off-by: Hao Zhang <hao.zhang@mediatek.com>
Co-developed-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The firmware support for management frame protection has limitations:
- do not support cipher BIP-GMAC-128 and BIP-GMAC-256
- support cipher BIP-CMAC-128 and BIP-CMAC-256, except action frame with
  action type 'not robust'.

Therefore, to simplify the logic, do not set the IGTK to firmware and
let the encryption of management frames be handled by upper layer.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Rong Yan <rong.yan@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Reduces size by avoiding duplicates
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is expected by the firmware of older chipsets as well, though it may
not have been as strongly required as on mt799x

Fixes: 098428c4 ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Check if background radar is enabled or not before manually triggering it,
and also add more checks in radar detected event.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For mt7992 chipsets, critical packet mode should be properly configured
to let the HW SDO module correctly fill the AC queue in TX descriptors of
some higher priority packets such as ARP and ICMP.
Without this patch, HW queues may hang when running MU traffic.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Without this commit, reading chip temperature will cause memory leakage.

Fixes: 6879b2e9 ("wifi: mt76: mt7996: add thermal sensor device support")
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not add UNI_BSS_INFO_11V_MBSSID tag when bssid_indicator is not set
to avoid abnormal beaconing behavior in non-11v MBSS scenario.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For mt7996 chipsets, the HW CSO module can help to identify TCP traffic,
which assists the firmware in adjusting algorithms to improve overall
performance.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the
FW rate control algorithm be initialized with a better MCS selection
table.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set peer address and aid for the BMC wtbl of station interface. For some
functions such as parsing MU_EDCA parameters from beacon, firmware will
need the peer address to do correct parsing.
Without this patch, MU uplink traffic would get suffered.
Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When a BMC wtbl of station interface is correctly set with peer address,
HW will do rx header translation for broadcast data packets, which makes
mac80211 unable to find the corresponding ieee80211_sta and drop the
packets. To fix this, disable HW rx header translation for BMC entry.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Looks like this was missed in the initial patch that made
the conversion to the emulated chanctx drivers.

Fixes: 0a44dfc0 ("wifi: mac80211: simplify non-chanctx drivers")
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Even if it is not a real issue at the moment since concurrent access to
mcu message queue is protected by mcu mutex, make the code more robust
and move mcu queue free space check inside queue spinlock critical section.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set intr1 to 0 in mt7996_irq_tasklet() in order to avoid possible
uninitialized variable usage if wed is not active for hif2.

Fixes: 83eafc92 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Before sending suspend & wow command to FW, its length should be
4-bytes alignd.

Fixes: c948b5da ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.

This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7920e is a mt7921 series chipset with 802.11ax 2x2:2SS support.
The major difference is in firmware side only, at this moment.
This patch would add some mandatory changes for new chip id and
firmware download control.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes issues with scanning and low power output at some rates.

Fixes: f75e4779 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Chad Monroe <chad@monroe.io>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The wcid can be NULL. It should be checked for validity before
dereferencing it to avoid crash.

Fixes: 098428c4 ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This flag is needed for the PSE client reset. Fixes watchdog reset issues.

Fixes: c677dda1 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.

Fixes: fca9615f ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>