The current JIT uses the following sequence to zero-extend into the
upper 32 bits of the destination register for BPF_LDX BPF_{B,H,W},
when the destination register is not on the stack:

  EMIT3(0xC7, add_1reg(0xC0, dst_hi), 0);

The problem is that C7 /0 encodes a MOV instruction that requires a 4-byte
immediate; the current code emits only 1 byte of the immediate. This
means that the first 3 bytes of the next instruction will be treated as
the rest of the immediate, breaking the stream of instructions.

This patch fixes the problem by instead emitting "xor dst_hi,dst_hi"
to clear the upper 32 bits. This fixes the problem and is more efficient
than using MOV to load a zero immediate.

This bug may not be currently triggerable as BPF_REG_AX is the only
register not stored on the stack and the verifier uses it in a limited
way, and the verifier implements a zero-extension optimization. But the
JIT should avoid emitting incorrect encodings regardless.

Fixes: 03f5781b ("bpf, x86_32: add eBPF JIT compiler for ia32")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Acked-by: Wang YanQing <udknight@gmail.com>
Link: https://lore.kernel.org/bpf/20200422173630.8351-1-luke.r.nels@gmail.com

The patch fixes:
$ scripts/bpf_helpers_doc.py > bpf-helpers.rst
$ rst2man bpf-helpers.rst > bpf-helpers.7
bpf-helpers.rst:1105: (WARNING/2) Inline strong start-string without end-string.
Signed-off-by: Jakub Wilk <jwilk@jwilk.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200422082324.2030-1-jwilk@jwilk.net

The commit in the Fixes tag changed get_xdp_id to only return prog_id
if flags is 0, but there are other XDP flags than the modes - e.g.,
XDP_FLAGS_UPDATE_IF_NOEXIST. Since the intention was only to look at
MODE flags, clear other ones before checking if flags is 0.

Fixes: f07cbad2 ("libbpf: Fix bpf_get_link_xdp_id flags handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrey Ignatov <rdna@fb.com>

This patch adds a test to test_verifier that writes the lower 8 bits of
R10 (aka FP) using BPF_B to an array map and reads the result back. The
expected behavior is that the result should be the same as first copying
R10 to R9, and then storing / loading the lower 8 bits of R9.

This test catches a bug that was present in the x86-64 JIT that caused
an incorrect encoding for BPF_STX BPF_B when the source operand is R10.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200418232655.23870-2-luke.r.nels@gmail.com

This patch fixes an encoding bug in emit_stx for BPF_B when the source
register is BPF_REG_FP.

The current implementation for BPF_STX BPF_B in emit_stx saves one REX
byte when the operands can be encoded using Mod-R/M alone. The lower 8
bits of registers %rax, %rbx, %rcx, and %rdx can be accessed without using
a REX prefix via %al, %bl, %cl, and %dl, respectively. Other registers,
(e.g., %rsi, %rdi, %rbp, %rsp) require a REX prefix to use their 8-bit
equivalents (%sil, %dil, %bpl, %spl).

The current code checks if the source for BPF_STX BPF_B is BPF_REG_1
or BPF_REG_2 (which map to %rdi and %rsi), in which case it emits the
required REX prefix. However, it misses the case when the source is
BPF_REG_FP (mapped to %rbp).

The result is that BPF_STX BPF_B with BPF_REG_FP as the source operand
will read from register %ch instead of the correct %bpl. This patch fixes
the problem by fixing and refactoring the check on which registers need
the extra REX byte. Since no BPF registers map to %rsp, there is no need
to handle %spl.

Fixes: 62258278 ("net: filter: x86: internal BPF JIT")
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200418232655.23870-1-luke.r.nels@gmail.com

check_xadd() can cause check_ptr_to_btf_access() to be executed with
atype==BPF_READ and value_regno==-1 (meaning "just check whether the access
is okay, don't tell me what type it will result in").
Handle that case properly and skip writing type information, instead of
indexing into the registers at index -1 and writing into out-of-bounds
memory.

Note that at least at the moment, you can't actually write through a BTF
pointer, so check_xadd() will reject the program after calling
check_ptr_to_btf_access with atype==BPF_WRITE; but that's after the
verifier has already corrupted memory.

This patch assumes that BTF pointers are not available in unprivileged
programs.

Fixes: 9e15db66 ("bpf: Implement accurate raw_tp context access via BTF")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200417000007.10734-2-jannh@google.com

When check_xadd() verifies an XADD operation on a pointer to a stack slot
containing a spilled pointer, check_stack_read() verifies that the read,
which is part of XADD, is valid. However, since the placeholder value -1 is
passed as `value_regno`, check_stack_read() can only return a binary
decision and can't return the type of the value that was read. The intent
here is to verify whether the value read from the stack slot may be used as
a SCALAR_VALUE; but since check_stack_read() doesn't check the type, and
the type information is lost when check_stack_read() returns, this is not
enforced, and a malicious user can abuse XADD to leak spilled kernel
pointers.

Fix it by letting check_stack_read() verify that the value is usable as a
SCALAR_VALUE if no type information is passed to the caller.

To be able to use __is_pointer_value() in check_stack_read(), move it up.

Fix up the expected unprivileged error message for a BPF selftest that,
until now, assumed that unprivileged users can use XADD on stack-spilled
pointers. This also gives us a test for the behavior introduced in this
patch for free.

In theory, this could also be fixed by forbidding XADD on stack spills
entirely, since XADD is a locked operation (for operations on memory with
concurrency) and there can't be any concurrency on the BPF stack; but
Alexei has said that he wants to keep XADD on stack slots working to avoid
changes to the test suite [1].

The following BPF program demonstrates how to leak a BPF map pointer as an
unprivileged user using this bug:

    // r7 = map_pointer
    BPF_LD_MAP_FD(BPF_REG_7, small_map),
    // r8 = launder(map_pointer)
    BPF_STX_MEM(BPF_DW, BPF_REG_FP, BPF_REG_7, -8),
    BPF_MOV64_IMM(BPF_REG_1, 0),
    ((struct bpf_insn) {
      .code  = BPF_STX | BPF_DW | BPF_XADD,
      .dst_reg = BPF_REG_FP,
      .src_reg = BPF_REG_1,
      .off = -8
    }),
    BPF_LDX_MEM(BPF_DW, BPF_REG_8, BPF_REG_FP, -8),

    // store r8 into map
    BPF_MOV64_REG(BPF_REG_ARG1, BPF_REG_7),
    BPF_MOV64_REG(BPF_REG_ARG2, BPF_REG_FP),
    BPF_ALU64_IMM(BPF_ADD, BPF_REG_ARG2, -4),
    BPF_ST_MEM(BPF_W, BPF_REG_ARG2, 0, 0),
    BPF_EMIT_CALL(BPF_FUNC_map_lookup_elem),
    BPF_JMP_IMM(BPF_JNE, BPF_REG_0, 0, 1),
    BPF_EXIT_INSN(),
    BPF_STX_MEM(BPF_DW, BPF_REG_0, BPF_REG_8, 0),

    BPF_MOV64_IMM(BPF_REG_0, 0),
    BPF_EXIT_INSN()

[1] https://lore.kernel.org/bpf/20200416211116.qxqcza5vo2ddnkdq@ast-mbp.dhcp.thefacebook.com/

Fixes: 17a52670 ("bpf: verifier (add verifier core)")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200417000007.10734-1-jannh@google.com

When the kernel is built with CONFIG_DEBUG_PER_CPU_MAPS, the cpumap code
can trigger a spurious warning if CONFIG_CPUMASK_OFFSTACK is also set. This
happens because in this configuration, NR_CPUS can be larger than
nr_cpumask_bits, so the initial check in cpu_map_alloc() is not sufficient
to guard against hitting the warning in cpumask_check().

Fix this by explicitly checking the supplied key against the
nr_cpumask_bits variable before calling cpu_possible().

Fixes: 6710e112 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Xiumei Mu <xmu@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200416083120.453718-1-toke@redhat.com

mlx5-fixes-2020-04-20
Signed-off-by: David S. Miller <davem@davemloft.net>

In the switchdev mode, when running "cat
/sys/class/net/NIC/statistics/tx_packets", the ppcnt register is
accessed to get the latest values. But currently this command can
not get the correct values from ppcnt.

From firmware manual, before getting the 802_3 counters, the 802_3
data layout should be set to the ppcnt register.

When the command "cat /sys/class/net/NIC/statistics/tx_packets" is
run, before updating 802_3 data layout with ppcnt register, the
monitor counters are tested. The test result will decide the
802_3 data layout is updated or not.

Actually the monitor counters do not support to monitor rx/tx
stats of 802_3 in switchdev mode. So the rx/tx counters change
will not trigger monitor counters. So the 802_3 data layout will
not be updated in ppcnt register. Finally this command can not get
the latest values from ppcnt register with 802_3 data layout.

Fixes: 5c7e8bbb ("net/mlx5e: Use monitor counters for update stats")
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MLX5_CORE uses the 'imply' keyword to depend on VXLAN, PTP_1588_CLOCK,
MLXFW and PCI_HYPERV_INTERFACE.

This was useful to force vxlan, ptp, etc.. to be reachable to mlx5
regardless of their config states.

Due to the changes in the cited commit below, the semantics of 'imply'
was changed to not force any restriction on the implied config.

As a result of this change, the compilation of MLX5_CORE=y and VXLAN=m
would result in undefined references, as VXLAN now would stay as 'm'.

To fix this we change MLX5_CORE to have a weak dependency on
these modules/configs and make sure they are reachable, by adding:
depend on symbol || !symbol.

For example: VXLAN=m MLX5_CORE=y, this will force MLX5_CORE to m

Fixes: def2fbff ("kconfig: allow symbols implied by y to become m")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Randy Dunlap <rdunlap@infradead.org>

XSK wakeup function triggers NAPI by posting a NOP WQE to a special XSK
ICOSQ. When the application floods the driver with wakeup requests by
calling sendto() in a certain pattern that ends up in mlx5e_trigger_irq,
the XSK ICOSQ may overflow.

Multiple NOPs are not required and won't accelerate the process, so
avoid posting a second NOP if there is one already on the way. This way
we also avoid increasing the queue size (which might not help anyway).

Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

After allowing parallel tuple insertion, we get the following trace:

[ 5505.142249] ------------[ cut here ]------------
[ 5505.148155] WARNING: CPU: 21 PID: 13313 at lib/radix-tree.c:581 delete_node+0x16c/0x180
[ 5505.295553] CPU: 21 PID: 13313 Comm: kworker/u50:22 Tainted: G           OE     5.6.0+ #78
[ 5505.304824] Hardware name: Supermicro Super Server/X10DRT-P, BIOS 2.0b 03/30/2017
[ 5505.313740] Workqueue: nf_flow_table_offload flow_offload_work_handler [nf_flow_table]
[ 5505.323257] RIP: 0010:delete_node+0x16c/0x180
[ 5505.349862] RSP: 0018:ffffb19184eb7b30 EFLAGS: 00010282
[ 5505.356785] RAX: 0000000000000000 RBX: ffff904ac95b86d8 RCX: ffff904b6f938838
[ 5505.365190] RDX: 0000000000000000 RSI: ffff904ac954b908 RDI: ffff904ac954b920
[ 5505.373628] RBP: ffff904b4ac13060 R08: 0000000000000001 R09: 0000000000000000
[ 5505.382155] R10: 0000000000000000 R11: 0000000000000040 R12: 0000000000000000
[ 5505.390527] R13: ffffb19184eb7bfc R14: ffff904b6bef5800 R15: ffff90482c1203c0
[ 5505.399246] FS:  0000000000000000(0000) GS:ffff904c2fc80000(0000) knlGS:0000000000000000
[ 5505.408621] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5505.415739] CR2: 00007f5d27006010 CR3: 0000000058c10006 CR4: 00000000001626e0
[ 5505.424547] Call Trace:
[ 5505.428429]  idr_alloc_u32+0x7b/0xc0
[ 5505.433803]  mlx5_tc_ct_entry_add_rule+0xbf/0x950 [mlx5_core]
[ 5505.441354]  ? mlx5_fc_create+0x23c/0x370 [mlx5_core]
[ 5505.448225]  mlx5_tc_ct_block_flow_offload+0x874/0x10b0 [mlx5_core]
[ 5505.456278]  ? mlx5_tc_ct_block_flow_offload+0x63d/0x10b0 [mlx5_core]
[ 5505.464532]  nf_flow_offload_tuple.isra.21+0xc5/0x140 [nf_flow_table]
[ 5505.472286]  ? __kmalloc+0x217/0x2f0
[ 5505.477093]  ? flow_rule_alloc+0x1c/0x30
[ 5505.482117]  flow_offload_work_handler+0x1d0/0x290 [nf_flow_table]
[ 5505.489674]  ? process_one_work+0x17c/0x580
[ 5505.494922]  process_one_work+0x202/0x580
[ 5505.500082]  ? process_one_work+0x17c/0x580
[ 5505.505696]  worker_thread+0x4c/0x3f0
[ 5505.510458]  kthread+0x103/0x140
[ 5505.514989]  ? process_one_work+0x580/0x580
[ 5505.520616]  ? kthread_bind+0x10/0x10
[ 5505.525837]  ret_from_fork+0x3a/0x50
[ 5505.570841] ---[ end trace 07995de9c56d6831 ]---

This happens from parallel deletes/adds to idr, as idr isn't protected.
Fix that by using xarray as the tuple_ids allocator instead of idr.

Fixes: 7da182a9 ("netfilter: flowtable: Use work entry per offload command")
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

On s390 FORCE_MAX_ZONEORDER is 9 instead of 11, thus a larger kzalloc()
allocation as done for the firmware tracer will always fail.

Looking at mlx5_fw_tracer_save_trace(), it is actually the driver itself
that copies the debug data into the trace array and there is no need for
the allocation to be contiguous in physical memory. We can therefor use
kvzalloc() instead of kzalloc() and get rid of the large contiguous
allcoation.

Fixes: f53aaa31 ("net/mlx5: FW tracer, implement tracer logic")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
    genl_lock(); by genl_rcv_msc()
        rtnl_lock(); by team_nl_cmd_options_set()
            mutex_lock(&team->lock); by team_nl_team_get()

Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
    genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.

The problem secenario.
CPU0                                     CPU1
team_mode_get
    request_module()
                                         modprobe -r team_mode_roundrobin
                                                     team <--(B)
        modprobe team <--(A)
            team_mode_roundrobin

By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.

By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.

Test commands:
    while :
    do
        teamd -d &
	killall teamd &
	modprobe -rv team_mode_roundrobin &
    done

The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.

Fixes: 3d249d4c ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
mptcp: fix races on accept()

This series includes some fixes for accept() races which may cause inconsistent
MPTCP socket status and oops. Please see the individual patches for the
technical details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't need them, as we can use the current ingress opt
data instead. Setting them in syn_recv_sock() may causes
inconsistent mptcp socket status, as per previous commit.

Fixes: cc7972ea ("mptcp: parse and emit MP_CAPABLE option according to v1 spec")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If multiple CPUs races on the same req_sock in syn_recv_sock(),
flipping such field can cause inconsistent child socket status.

When racing, the CPU losing the req ownership may still change
the mptcp request socket mp_capable flag while the CPU owning
the request is cloning the socket, leaving the child socket with
'is_mptcp' set but no 'mp_capable' flag.

Such socket will stay with 'conn' field cleared, heading to oops
in later mptcp callback.

Address the issue tracking the fallback status in a local variable.

Fixes: 58b09919 ("mptcp: create msk early")
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following splat can occur during self test:

 BUG: KASAN: use-after-free in subflow_data_ready+0x156/0x160
 Read of size 8 at addr ffff888100c35c28 by task mptcp_connect/4808

  subflow_data_ready+0x156/0x160
  tcp_child_process+0x6a3/0xb30
  tcp_v4_rcv+0x2231/0x3730
  ip_protocol_deliver_rcu+0x5c/0x860
  ip_local_deliver_finish+0x220/0x360
  ip_local_deliver+0x1c8/0x4e0
  ip_rcv_finish+0x1da/0x2f0
  ip_rcv+0xd0/0x3c0
  __netif_receive_skb_one_core+0xf5/0x160
  __netif_receive_skb+0x27/0x1c0
  process_backlog+0x21e/0x780
  net_rx_action+0x35f/0xe90
  do_softirq+0x4c/0x50
  [..]

This occurs when accessing subflow_ctx->conn.

Problem is that tcp_child_process() calls listen sockets'
sk_data_ready() notification, but it doesn't hold the listener
lock.  Another cpu calling close() on the listener will then cause
transition of refcount to 0.

Fixes: 58b09919 ("mptcp: create msk early")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.

Fixes: 9c33e420 ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:

==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G            E     5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
 dump_backtrace+0x0/0x2a0
 show_stack+0x20/0x30
 dump_stack+0xec/0x148
 print_address_description.isra.12+0x70/0x35c
 __kasan_report+0xfc/0x1d4
 kasan_report+0x4c/0x68
 __asan_load4+0x9c/0xd8
 _get_maxdiv+0x74/0xd8
 clk_divider_bestdiv+0x74/0x5e0
 clk_divider_round_rate+0x80/0x1a8
 clk_core_determine_round_nolock.part.9+0x9c/0xd0
 clk_core_round_rate_nolock+0xf0/0x108
 clk_hw_round_rate+0xac/0xf0
 clk_factor_round_rate+0xb8/0xd0
 clk_core_determine_round_nolock.part.9+0x9c/0xd0
 clk_core_round_rate_nolock+0xf0/0x108
 clk_core_round_rate_nolock+0xbc/0x108
 clk_core_set_rate_nolock+0xc4/0x2e8
 clk_set_rate+0x58/0xe0
 meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
 platform_drv_probe+0x78/0xd8
 really_probe+0x158/0x610
 driver_probe_device+0x140/0x1b0
 device_driver_attach+0xa4/0xb0
 __driver_attach+0xcc/0x1c8
 bus_for_each_dev+0xf4/0x168
 driver_attach+0x3c/0x50
 bus_add_driver+0x238/0x2e8
 driver_register+0xc8/0x1e8
 __platform_driver_register+0x88/0x98
 meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
 do_one_initcall+0xa8/0x328
 do_init_module+0xe8/0x368
 load_module+0x3300/0x36b0
 __do_sys_finit_module+0x120/0x1a8
 __arm64_sys_finit_module+0x4c/0x60
 el0_svc_common.constprop.2+0xe4/0x268
 do_el0_svc+0x98/0xa8
 el0_svc+0x24/0x68
 el0_sync_handler+0x12c/0x318
 el0_sync+0x158/0x180

The buggy address belongs to the variable:
 div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]

Memory state around the buggy address:
 ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
 ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
                                                             ^
 ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
 ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================

Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.

Let's add the empty structure that indicates the end of the array.

Fixes: bd6f4854 ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.

Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.

Fixes: b6f61189 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

In the function bcm_sysport_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant message
here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot wrote:
| =============================
| WARNING: suspicious RCU usage
| 5.7.0-rc1+ #45 Not tainted
| -----------------------------
| net/openvswitch/conntrack.c:1898 RCU-list traversed in non-reader section!!
|
| other info that might help us debug this:
| rcu_scheduler_active = 2, debug_locks = 1
| ...
|
| stack backtrace:
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-0-ga698c8995f-prebuilt.qemu.org 04/01/2014
| Workqueue: netns cleanup_net
| Call Trace:
| ...
| ovs_ct_exit
| ovs_exit_net
| ops_exit_list.isra.7
| cleanup_net
| process_one_work
| worker_thread

To avoid that warning, invoke the ovs_ct_exit under ovs_lock and add
lockdep_ovsl_is_held as optional lockdep expression.

Link: https://lore.kernel.org/lkml/000000000000e642a905a0cbee6e@google.com
Fixes: 11efd5cb ("openvswitch: Support conntrack zone limit")
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Yi-Hung Wei <yihung.wei@gmail.com>
Reported-by: syzbot+7ef50afd3a211f879112@syzkaller.appspotmail.com
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP stack is dumb in how it cooks its output packets.

Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.

If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
mptcp: fix 'attempt to release socket in state...' splats

These two patches fix error handling corner-cases where
inet_sock_destruct gets called for a mptcp_sk that is not in TCP_CLOSE
state.  This results in unwanted error printks from the network stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to set sk_state to CLOSED, else we will get following:

IPv4: Attempt to release TCP socket in state 3 00000000b95f109e
IPv4: Attempt to release TCP socket in state 10 00000000b95f109e

First one is from inet_sock_destruct(), second one from
mptcp_sk_clone failure handling.  Setting sk_state to CLOSED isn't
enough, we also need to orphan sk so it has DEAD flag set.
Otherwise, a very similar warning is printed from inet_sock_destruct().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following snippet (replicated from syzkaller reproducer) generates
warning: "IPv4: Attempt to release TCP socket in state 1".

int main(void) {
 struct sockaddr_in sin1 = { .sin_family = 2, .sin_port = 0x4e20,
                             .sin_addr.s_addr = 0x010000e0, };
 struct sockaddr_in sin2 = { .sin_family = 2,
	                     .sin_addr.s_addr = 0x0100007f, };
 struct sockaddr_in sin3 = { .sin_family = 2, .sin_port = 0x4e20,
	                     .sin_addr.s_addr = 0x0100007f, };
 int r0 = socket(0x2, 0x1, 0x106);
 int r1 = socket(0x2, 0x1, 0x106);

 bind(r1, (void *)&sin1, sizeof(sin1));
 connect(r1, (void *)&sin2, sizeof(sin2));
 listen(r1, 3);
 return connect(r0, (void *)&sin3, 0x4d);
}

Reason is that the newly generated mptcp socket is closed via the ulp
release of the tcp listener socket when its accept backlog gets purged.

To fix this, delay setting the ESTABLISHED state until after userspace
calls accept and via mptcp specific destructor.

Fixes: 58b09919 ("mptcp: create msk early")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/9Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9ecc2d86 ("net/mlx4_en: add xdp forwarding and data write support")
brought another indirect call in fast path.

Use INDIRECT_CALL_2() helper to avoid the cost of the indirect call
when/if CONFIG_RETPOLINE=y
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes it impossible that cmpri or cmpre values are set to the
value 16 which is not possible, because these are 4 bit values. We
currently run in an overflow when assigning the value 16 to it.

According to the standard a value of 16 can be interpreted as a full
elided address which isn't possible to set as compression value. A reason
why this cannot be set is that the current ipv6 header destination address
should never show up inside the segments of the rpl header. In this case we
run in a overflow and the address will have no compression at all. Means
cmpri or compre is set to 0.

As we handle cmpri and cmpre sometimes as unsigned char or 4 bit value
inside the rpl header the current behaviour ends in an invalid header
format. This patch simple use the best compression method if we ever run
into the case that the destination address is showed up inside the rpl
segments. We avoid the overflow handling and the rpl header is still valid,
even when we have the destination address inside the rpl segments.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In fine adjustement mode, which is the current default, the sub-second
    increment register is the number of nanoseconds that will be added to
    the clock when the accumulator overflows. At each clock cycle, the
    value of the addend register is added to the accumulator.
    Currently, we use 20ns = 1e09ns / 50MHz as this value whatever the
    frequency of the ptp clock actually is.
    The adjustment is then done on the addend register, only incrementing
    every X clock cycles X being the ratio between 50MHz and ptp_clock_rate
    (addend = 2^32 * 50MHz/ptp_clock_rate).
    This causes the following issues :
    - In case the frequency of the ptp clock is inferior or equal to 50MHz,
      the addend value calculation will overflow and the default
      addend value will be set to 0, causing the clock to not work at
      all. (For instance, for ptp_clock_rate = 50MHz, addend = 2^32).
    - The resolution of the timestamping clock is limited to 20ns while it
      is not needed, thus limiting the accuracy of the timestamping to
      20ns.

    Fix this by setting sub-second increment to 2e09ns / ptp_clock_rate.
    It will allow to reach the minimum possible frequency for
    ptp_clk_ref, which is 5MHz for GMII 1000Mps Full-Duplex by setting the
    sub-second-increment to a higher value. For instance, for 25MHz, it
    gives ssinc = 80ns and default_addend = 2^31.
    It will also allow to use a lower value for sub-second-increment, thus
    improving the timestamping accuracy with frequencies higher than
    100MHz, for instance, for 200MHz, ssinc = 10ns and default_addend =
    2^31.

v1->v2:
 - Remove modifications to the calculation of default addend, which broke
 compatibility with clock frequencies for which 2000000000 / ptp_clk_freq
 is not an integer.
 - Modify description according to discussions.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 2 registers to write to enable a ptp ref clock coming from the
fpga.
One that enables the usage of the clock from the fpga for emac0 and emac1
as a ptp ref clock, and the other to allow signals from the fpga to reach
emac0 and emac1.
Currently, if the dwmac-socfpga has phymode set to PHY_INTERFACE_MODE_MII,
PHY_INTERFACE_MODE_GMII, or PHY_INTERFACE_MODE_SGMII, both registers will
be written and the ptp ref clock will be set as coming from the fpga.
Separate the 2 register writes to only enable signals from the fpga to
reach emac0 or emac1 when ptp ref clock is not coming from the fpga.
Signed-off-by: Julien Beraud <julien.beraud@orolia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

i2400mu_bus_bm_wait_for_ack() invokes usb_get_urb(), which increases the
refcount of the "notif_urb".

When i2400mu_bus_bm_wait_for_ack() returns, local variable "notif_urb"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.

The issue happens in all paths of i2400mu_bus_bm_wait_for_ack(), which
forget to decrease the refcnt increased by usb_get_urb(), causing a
refcnt leak.

Fix this issue by calling usb_put_urb() before the
i2400mu_bus_bm_wait_for_ack() returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_rcv() invokes tipc_node_find() twice, which returns a reference of
the specified tipc_node object to "n" with increased refcnt.

When tipc_rcv() returns or a new object is assigned to "n", the original
local reference of "n" becomes invalid, so the refcount should be
decreased to keep refcount balanced.

The issue happens in some paths of tipc_rcv(), which forget to decrease
the refcnt increased by tipc_node_find() and will cause a refcnt leak.

Fix this issue by calling tipc_node_put() before the original object
pointed by "n" becomes invalid.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_crypto_rcv() invokes tipc_aead_get(), which returns a reference of
the tipc_aead object to "aead" with increased refcnt.

When tipc_crypto_rcv() returns, the original local reference of "aead"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.

The issue happens in one error path of tipc_crypto_rcv(). When TIPC
message decryption status is EINPROGRESS or EBUSY, the function forgets
to decrease the refcnt increased by tipc_aead_get() and causes a refcnt
leak.

Fix this issue by calling tipc_aead_put() on the error path when TIPC
message decryption status is EINPROGRESS or EBUSY.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.

When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.

The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.

Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome-platform fixes from Benson Leung:
 "Two small fixes for cros_ec_sensorhub_ring.c, addressing issues
  introduced in the cros_ec_sensorhub FIFO support commit"

* tag 'tag-chrome-platform-fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_ec_sensorhub: Add missing '\n' in log messages
  platform/chrome: cros_ec_sensorhub: Off by one in cros_sensorhub_send_sample()

Pull networking fixes from David Miller:

 1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.

 2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.

 3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.

 4) Adjust icmp6 message source address selection when routes have a
    preferred source address set, from Tim Stallard.

 5) Be sure to validate HSR protocol version when creating new links,
    from Taehee Yoo.

 6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
    non-initial namespaces, from Michael Weiß.

 7) Missing release firmware call in mlx5, from Eran Ben Elisha.

 8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
    Taehee Yoo.

 9) Fix pause frame negotiation in marvell phy driver, from Clemens
    Gruber.

10) Record RX queue early enough in tun packet paths such that XDP
    programs will see the correct RX queue index, from Gilberto Bertin.

11) Fix double unlock in mptcp, from Florian Westphal.

12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.

13) marvell10g needs to soft reset PHY when coming out of low power
    mode, from Russell King.

14) Fix MTU setting regression in stmmac for some chip types, from
    Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
  amd-xgbe: Use __napi_schedule() in BH context
  mISDN: make dmril and dmrim static
  net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
  net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
  tipc: fix incorrect increasing of link window
  Documentation: Fix tcp_challenge_ack_limit default value
  net: tulip: make early_486_chipsets static
  dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
  ipv6: remove redundant assignment to variable err
  net/rds: Use ERR_PTR for rds_message_alloc_sgs()
  net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
  selftests/bpf: Check for correct program attach/detach in xdp_attach test
  libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
  libbpf: Always specify expected_attach_type on program load if supported
  xsk: Add missing check on user supplied headroom size
  mac80211: fix channel switch trigger from unknown mesh peer
  mac80211: fix race in ieee80211_register_hw()
  net: marvell10g: soft-reset the PHY when coming out of low power
  net: marvell10g: report firmware version
  net/cxgb4: Check the return from t4_query_params properly
  ...

The driver uses __napi_schedule_irqoff() which is fine as long as it is
invoked with disabled interrupts by everybody. Since the commit
mentioned below the driver may invoke xgbe_isr_task() in tasklet/softirq
context. This may lead to list corruption if another driver uses
__napi_schedule_irqoff() in IRQ context.

Use __napi_schedule() which safe to use from IRQ and softirq context.

Fixes: 85b85c85 ("amd-xgbe: Re-issue interrupt if interrupt status not cleared")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following sparse warning:

drivers/isdn/hardware/mISDN/mISDNisar.c:746:12: warning: symbol 'dmril'
was not declared. Should it be static?
drivers/isdn/hardware/mISDN/mISDNisar.c:749:12: warning: symbol 'dmrim'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>