The original implementation removes reverse links for any input link and
assumes the presense of sink/source.
It fails when the link is a not a data link.
media_entity_remove_links when there's an ancillary link can also fail.

We only need to remove reverse links for a data link.
Signed-off-by: Yunke Cao <yunkec@google.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Add support for MEDIA_BUS_FMT_JPEG_1X8 media bus code to the
CSIS driver.

The MEDIA_BUS_FMT_JPEG_1X8 code is mapped to the RAW8 CSI-2 Data Type,
while the CSI-2 specification suggests to use User Defined Data Type 1.

As reported in the comment, the CSIS interface captures arbitrary Data
Types by using a pixel sampling mode not supported by the IP core
connected to it on i.MX SoCs.

As some sensors, such as OV5640, support sending JPEG data on the RAW8
Data Type and capture operations work correcty with such configuration,
map MEDIA_BUS_FMT_JPEG_1X8 to Data Type 0x2a.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

This new optional callback is called when the adapter is fully configured
or fully unconfigured. Some drivers may have to take action when this
happens.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Allow drivers to change the transmit timeout value, i.e. after how
long should a transmit be considered 'lost', i.e. the corresponding
cec_transmit_done_ts was never called.

Some CEC devices have their own timeout, and so this timeout value must be
longer than that hardware timeout value. If it is shorter then the
framework would consider the transmit lost, even though it is effectively
still in progress at the hardware level.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Use call_(void_)op consistently in the CEC core framework. Ditto
for the cec pin ops. And check if !adap->devnode.unregistered before
calling each op. This avoids calls to ops when the device has been
unregistered and the underlying hardware may be gone.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

These two helper functions return true if the received message
contains the result of a previous non-blocking transmit. Either
the tx_status result (cec_msg_recv_is_tx_result) of the transmit,
or the rx_status result (cec_msg_recv_is_rx_result) of the reply
to the original transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The results of non-blocking transmits were not correctly communicated
to userspace.

Specifically:

1) if a non-blocking transmit was canceled, then rx_status wasn't set to 0
   as it should.
2) if the non-blocking transmit succeeded, but the corresponding reply
   never arrived (aborted or timed out), then tx_status wasn't set to 0
   as it should, and rx_status was hardcoded to ABORTED instead of the
   actual reason, such as TIMEOUT. In addition, adap->ops->received() was
   never called, so drivers that want to do message processing themselves
   would not be informed of the failed reply.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

If a transmit-in-progress was canceled, then, once the transmit
is done, mark it as aborted and refrain from retrying the transmit.

To signal this situation the new transmit_in_progress_aborted field is
set to true.

The old implementation would just set adap->transmitting to NULL and
set adap->transmit_in_progress to false, but on the hardware level
the transmit was still ongoing. However, the framework would think
the transmit was aborted, and if a new transmit was issued, then
it could overwrite the HW buffer containing the old transmit with the
new transmit, leading to garbled data on the CEC bus.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Don't enable/disable the adapter if the first fh is opened or the
last fh is closed, instead do this when the adapter is configured
or unconfigured, and also when we enter Monitor All or Monitor Pin
mode for the first time or we exit the Monitor All/Pin mode for the
last time.

However, if needs_hpd is true, then do this when the physical
address is set or cleared: in that case the adapter typically is
powered by the HPD, so it really is disabled when the HPD is low.
This case (needs_hpd is true) was already handled in this way, so
this wasn't changed.

The problem with the old behavior was that if the HPD goes low when
no fh is open, and a transmit was in progress, then the adapter would
be disabled, typically stopping the transmit immediately which
leaves a partial message on the bus, which isn't nice and can confuse
some adapters.

It makes much more sense to disable it only when the adapter is
unconfigured and we're not monitoring the bus, since then you really
won't be using it anymore.

To keep track of this store a CEC activation count and call adap_enable
only when it goes from 0 to 1 or back to 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Remove dev_err() messages after platform_get_irq*() failures.
platform_get_irq() already prints an error.

Generated by: scripts/coccinelle/api/platform_get_irq.cocci
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/028699ec71158dbc49d710a4259eb8cdb7f673cb.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/f1d4fa4960b709152ae693800c830e19a4bc1f48.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/a300c26ad4e9bb913e86eeaf0ec7d72b9e7d5d3e.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/0241bf842bf592dfa01b0ef4916afda396194f98.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/13bf6aab3909fae5da4c9a24c114b15e76abd146.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/5fd3c469faa115856f48037019e607edcb41d458.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/b447d9fd3832da5eff6267e8fe742c431f1133f2.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro.

Link: https://lore.kernel.org/linux-media/c125c28aeb3d4344b632e1f99d81c433917f2a4c.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/283a8c6bdf9778f832b4f6acc104c06688281668.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/08861d80b6706ac1ed04a68959ebb78f27cb028d.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/58f1a356b7b75bbefef3aa07cd99896c446df32f.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/c6f6bab97c39561add54f69a75980f4d453f7c17.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/0d32148747df677f0c930605389c12b190c09bdf.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro, and rename some PIDs.

Link: https://lore.kernel.org/linux-media/828998ef3f0843bab4e84780e42f8f0802f57be7.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro.

Link: https://lore.kernel.org/linux-media/6e7183735aacf33fff86bc709a38aafb6b858dff.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/9fa3d1add4c58e1320dcc18578fda2d0106becda.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro.

Link: https://lore.kernel.org/linux-media/68de8820a361e61c25bf7402acac71b3770ff906.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro.

Link: https://lore.kernel.org/linux-media/bd1e61664e234252de3dfac16aab8bfc35b7bcd7.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro and an enum with the USB model supported by
this driver.

Link: https://lore.kernel.org/linux-media/4b8212adab277a2bf84ab04480eb6fd37edda74f.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/65b9775c39dcd21e5cb75a86e1e7b99b7d6eefcd.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to make the drivers under dvb-usb more homogeneous,
use the new macro.

Link: https://lore.kernel.org/linux-media/9b1749763465815af92f0a4d8f210fe170c549d5.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The device number is currently a value that needs to be the same
on two separate tables, but the code doesn't actually enforce it,
leading to errors as boards get added or removed.

Fix it by using an enum.

Link: https://lore.kernel.org/linux-media/dc8f9ec6cc8f2e16967a61752a292c46622c01dc.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

In order to use designated initializers and to avoid avoid big lines
at the USB ID tables, define some helper macros.

Link: https://lore.kernel.org/linux-media/f82e376dea2e9b922f51a03d1e7730b03e49cc7d.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

There are two commented entries that are pointing to the wrong
places. Fix them.

Link: https://lore.kernel.org/linux-media/fe9ee24510431e6baad5244d8a27e56ce167fc36.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Almost all drivers based on dvb-usb place their USB IDs
at dvb-usb-ids.h. In order to make it more standard, place
the remaining ones also there.

Link: https://lore.kernel.org/linux-media/7b32d5383169d23082758a7b69edef2f099202f3.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

The entries there are alphabetically sorted, but some are at the
wrong place. Re-sort them.

While here, replace spaces by tabs where needed.

Link: https://lore.kernel.org/linux-media/0208dbba189b754b999759f06c2584242c879f4d.1648499509.git.mchehab@kernel.orgSigned-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Pull xen fixlet from Juergen Gross:
 "A single cleanup patch for the Xen balloon driver"

* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't use PV mode extra memory for zone device allocations

Pull x86 fixes from Thomas Gleixner:
 "Two x86 fixes related to TSX:

   - Use either MSR_TSX_FORCE_ABORT or MSR_IA32_TSX_CTRL to disable TSX
     to cover all CPUs which allow to disable it.

   - Disable TSX development mode at boot so that a microcode update
     which provides TSX development mode does not suddenly make the
     system vulnerable to TSX Asynchronous Abort"

* tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsx: Disable TSX development mode at boot
  x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for the timers core:

   - Fix the warning condition in __run_timers() which does not take
     into account that a CPU base (especially the deferrable base) never
     has a timer armed on it and therefore the next_expiry value can
     become stale.

   - Replace a WARN_ON() in the NOHZ code with a WARN_ON_ONCE() to
     prevent endless spam in dmesg.

   - Remove the double star from a comment which is not meant to be in
     kernel-doc format"

* tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/sched: Fix non-kernel-doc comment
  tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
  timers: Fix warning condition in __run_timers()