This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
  - hub_resume
    - usb_disable_interface
      - usb_disable_endpoint
        - usb_hcd_disable_endpoint
          - xhci_endpoint_disable  // it set @ep->hcpriv to NULL

Then when reset usb device, it will drop allocated endpoints,
the flow as below:
  - usb_reset_and_verify_device
    - usb_hcd_alloc_bandwidth
      - xhci_mtk_drop_ep

but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.

Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.

Fixes: 4ce18666 ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819080556.32215-1-chunfeng.yun@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.

According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.

For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:

        dp->alt->vdo=0x140045

The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.

This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.

To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.

Fixes: 0e3bb7d6 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

onboard_hub_power_off() currently has a delay after asserting the
reset of the hub. There is already a delay in onboard_hub_power_on()
before de-asserting the reset, which ensures that the reset is
asserted for the required time, so the delay in _power_off() is not
needed.

Skip the reset GPIO check before calling gpiod_set_value_cansleep(),
the function returns early when the GPIO descriptor is NULL.
Reviewed-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220805111836.1.Id5a4dc0a2c046236116693aa55672295513a0f2a@changeidSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions.  If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop.  Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.

This patch depends on
  commit 69e131d1 ("usb: dwc3: gadget: Prevent repeat pullup()")

Fixes: 77adb8bd ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.

Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220815123334.87526-1-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the necessary ACPI ID for Intel Meteor Lake
IOM devices.

The callback function is_memory() is modified so that it
also checks if the resource descriptor passed to it is a
memory type "Address Space Resource Descriptor".

On Intel Meteor Lake the ACPI memory resource is not
described using the "32-bit Memory Range Descriptor" because
the memory is outside of the 32-bit address space. The
memory resource is described using the "Address Space
Resource Descriptor" instead.

Intel Meteor Lake is the first platform to describe the
memory resource for this device with Address Space Resource
Descriptor, but it most likely will not be the last.
Therefore the change to the is_memory() callback function
is made generic.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable@vger.kernel.org
[ heikki: Rewrote the commit message. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220816101629.69054-2-heikki.krogerus@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a compatible for DWC3 found on SM6375.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220716193257.456023-4-konrad.dybcio@somainline.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the suspend callbacks by separating the error and success paths
to improve readability.

Also drop a related redundant initialisation.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-10-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is the Qualcomm glue wakeup interrupts that may be able to wake the
system from suspend and this can now be described in the devicetree.

Move the wakeup-source property handling over from the core driver and
instead propagate the capability setting to the core device during
probe.

This is needed as there is currently no way for the core driver to query
the wakeup setting of the glue device, but it is the core driver that
manages the PHY power state during suspend.

Also don't leave the PHYs enabled when system wakeup has been disabled
through sysfs.

Fixes: 649f5c84 ("usb: dwc3: core: Host wake up support from system suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-9-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a wakeup-source property to the binding to describe whether the
wakeup interrupts can wake the system from suspend.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-8-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A recent commit implementing wakeup support in host mode instead broke
suspend for peripheral and OTG mode.

The hack that was added in the suspend path to determine the speed of
any device connected to the USB2 bus not only accesses internal driver
data for a child device, but also dereferences a NULL pointer or
accesses freed data when the controller is not acting as host.

There's no quick fix to the layering violation, but since reverting
would leave us with broken suspend in host mode with wakeup triggering
immediately, let's keep the hack for now.

Fix the immediate issues by only checking the host bus speed and
enabling wakeup interrupts when acting as host.

Fixes: 6895ea55 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-7-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A device must enable wakeups during runtime suspend regardless of
whether it is capable and allowed to wake the system up from system
suspend.

Fixes: 2664deb0 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-6-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.

After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.

Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.

Also note that runtime PM has been broken since commit 2664deb0
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.

Fixes: a4333c3a ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org      # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A recent change added a dependency to the USB host stack and broke
gadget-only builds of the driver.

Fixes: 6895ea55 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-4-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit d9be8d5c.

Generic power-domain flags must be set before the power-domain is
initialised and must specifically not be modified by drivers for devices
that happen to be in the domain.

To make sure that USB power-domains are left enabled during system
suspend when a device in the domain is in the wakeup path, the
GENPD_FLAG_ACTIVE_WAKEUP flag should instead be set for the domain
unconditionally when it is registered.

Note that this also avoids keeping power-domains on during suspend when
wakeup has not been enabled (e.g. through sysfs).

For the runtime PM case, making sure that the PHYs are not suspended and
that they are in the same domain as the controller prevents the domain
from being suspended. If there are cases where this is not possible or
desirable, the genpd implementation may need to be extended.

Fixes: d9be8d5c ("usb: dwc3: qcom: Keep power domain on to retain controller status")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-3-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Generic PHYs must be powered-off before they can be tore down.

Similarly, suspending legacy PHYs after having powered them off makes no
sense.

Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded
dwc3_probe() error-path sequences that got this wrong.

Note that this makes dwc3_core_exit() match the dwc3_core_init() error
path with respect to powering off the PHYs.

Fixes: 03c1fd62 ("usb: dwc3: core: add phy cleanup for probe error handling")
Fixes: c499ff71 ("usb: dwc3: core: re-factor init and exit paths")
Cc: stable@vger.kernel.org      # 4.8
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is USB mass storage primary boot loader for code download on
NXP PN7462AU.

Without the quirk it is impossible to write whole memory at once as
device restarts during the write due to bogus residue values reported.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Witold Lipieta <witold.lipieta@thaumatec.com>
Link: https://lore.kernel.org/r/20220809112911.462776-1-witold.lipieta@thaumatec.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.

[   84.308251] state change SNK_READY -> SNK_NEGOTIATE_CAPABILITIES [rev3 NONE_AMS]
[   84.308335] Setting usb_comm capable false
[   84.323367] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:5000 ret:0
[   84.323376] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]

Fixes: e9e6e164 ("usb: typec: tcpm: Support non-PD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220817215410.1807477-1-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.

It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.

Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.

Fixes: ab37a7a8 ("ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in")
Fixes: c0442479 ("usb: musb: Fix randconfig build issues for Kconfig options")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220818135737.3143895-10-arnd@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well

Pull more cifs updates from Steve French:

 - two fixes for stable, one for a lock length miscalculation, and
   another fixes a lease break timeout bug

 - improvement to handle leases, allows the close timeout to be
   configured more safely

 - five restructuring/cleanup patches

* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
  cifs: Add constructor/destructors for tcon->cfid
  SMB3: fix lease break timeout when multiple deferred close handles for the same file.
  smb3: allow deferred close timeout to be configurable
  cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
  cifs: Move cached-dir functions into a separate file
  cifs: Remove {cifs,nfs}_fscache_release_page()
  cifs: fix lock length calculation

Enable multipage folio support for the afs filesystem.

Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.

Note that it does require a change to afs_write_begin() to return the
correct subpage.  This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Ingo Molnar:
 "Misc timer fixes:

   - fix a potential use-after-free bug in posix timers

   - correct a prototype

   - address a build warning"

* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Cleanup CPU timers before freeing them during exec
  time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
  posix-timers: Make do_clock_gettime() static

Pull x86 fix from Ingo Molnar:
 "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
  turned on by default), which also need STIBP enabled (if available) to
  be '100% safe' on even the shortest speculation windows"

* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Enable STIBP for IBPB mitigated RETBleed

Pull more i2c updates from Wolfram Sang:

 - two driver fixes for issues introduced this cycle

 - one trivial driver improvement regarding ACPI

 - more DTS conversion and additions

 - documentation updates

 - subsystem-wide move from strlcpy to strscpy

* tag 'i2c-for-5.20-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  docs: i2c: i2c-sysfs: fix hyperlinks
  docs: i2c: i2c-sysfs: improve wording
  docs: i2c: instantiating-devices: add syntax coloring to dts and C blocks
  docs: i2c: smbus-protocol: improve DataLow/DataHigh definition
  docs: i2c: i2c-protocol: remove unused legend items
  docs: i2c: i2c-protocol,smbus-protocol: remove nonsense words
  docs: i2c: i2c-protocol: update introductory paragraph
  i2c: move core from strlcpy to strscpy
  i2c: move drivers from strlcpy to strscpy
  i2c: kempld: Support ACPI I2C device declaration
  i2c: mediatek: add i2c compatible for MT8188
  dt-bindings: i2c: update bindings for mt8188 soc
  i2c: microchip-corei2c: fix erroneous late ack send
  dt-bindings: i2c: qcom,i2c-cci: convert to dtschema
  i2c: qcom-geni: Fix GPI DMA buffer sync-back

Pull NTB updates from Jon Mason:
 "Non-Transparent Bridge updates.

  Fix of heap data and clang warnings, support for a new Intel NTB
  device, and NTB EndPoint Function (EPF) support and the various fixes
  for that"

* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
  MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
  NTB: EPF: Tidy up some bounds checks
  NTB: EPF: Fix error code in epf_ntb_bind()
  PCI: endpoint: pci-epf-vntb: reduce several globals to statics
  PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
  PCI: endpoint: Fix Kconfig dependency
  NTB: EPF: set pointer addr to null using NULL rather than 0
  Documentation: PCI: extend subheading underline for "lspci output" section
  Documentation: PCI: Use code-block block for scratchpad registers diagram
  Documentation: PCI: Add specification for the PCI vNTB function device
  PCI: endpoint: Support NTB transfer between RC and EP
  NTB: epf: Allow more flexibility in the memory BAR map method
  PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
  ntb: intel: add GNR support for Intel PCIe gen5 NTB
  NTB: ntb_tool: uninitialized heap data in tool_fn_write()
  ntb: idt: fix clang -Wformat warnings

Pull more xfs updates from Darrick Wong:
 "There's not a lot this time around, just the usual bug fixes and
  corrections for missing error returns.

   - Return error codes from block device flushes to userspace

   - Fix a deadlock between reclaim and mount time quotacheck

   - Fix an unnecessary ENOSPC return when doing COW on a filesystem
     with severe free space fragmentation

   - Fix a miscalculation in the transaction reservation computations
     for file removal operations"

* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix inode reservation space for removing transaction
  xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
  xfs: fix intermittent hang during quotacheck
  xfs: check return codes when flushing block devices

Pull more SCSI updates from James Bottomley:
 "Mostly small bug fixes and trivial updates.

  The major new core update is a change to the way device, target and
  host reference counting is done to try to make it more robust (this
  change has soaked for a while to try to winkle out any bugs)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: pm8001: Fix typo 'the the' in comment
  scsi: megaraid_sas: Remove redundant variable cmd_type
  scsi: FlashPoint: Remove redundant variable bm_int_st
  scsi: zfcp: Fix missing auto port scan and thus missing target ports
  scsi: core: Call blk_mq_free_tag_set() earlier
  scsi: core: Simplify LLD module reference counting
  scsi: core: Make sure that hosts outlive targets
  scsi: core: Make sure that targets outlive devices
  scsi: ufs: ufs-pci: Correct check for RESET DSM
  scsi: target: core: De-RCU of se_lun and se_lun acl
  scsi: target: core: Fix race during ACL removal
  scsi: ufs: core: Correct ufshcd_shutdown() flow
  scsi: ufs: core: Increase the maximum data buffer size
  scsi: lpfc: Check the return value of alloc_workqueue()

Pull block fixes from Jens Axboe:

 - NVMe pull request
     - print nvme connect Linux error codes properly (Amit Engel)
     - fix the fc_appid_store return value (Christoph Hellwig)
     - fix a typo in an error message (Christophe JAILLET)
     - add another non-unique identifier quirk (Dennis P. Kliem)
     - check if the queue is allocated before stopping it in nvme-tcp
       (Maurizio Lombardi)
     - restart admin queue if the caller needs to restart queue in
       nvme-fc (Ming Lei)
     - use kmemdup instead of kmalloc + memcpy in nvme-auth (Zhang
       Xiaoxu)

 - __alloc_disk_node() error handling fix (Rafael)

* tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block:
  block: Do not call blk_put_queue() if gendisk allocation fails
  nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S70
  nvme-tcp: check if the queue is allocated before stopping it
  nvme-fabrics: Fix a typo in an error message
  nvme-fabrics: parse nvme connect Linux error codes
  nvmet-auth: use kmemdup instead of kmalloc + memcpy
  nvme-fc: fix the fc_appid_store return value
  nvme-fc: restart admin queue if the caller needs to restart queue

Pull io_uring fixes from Jens Axboe:

 - Regression fix for this merge window, fixing a wrong order of
   arguments for io_req_set_res() for passthru (Dylan)

 - Fix for the audit code leaking context memory (Peilin)

 - Ensure that provided buffers are memcg accounted (Pavel)

 - Correctly handle short zero-copy sends (Pavel)

 - Sparse warning fixes for the recvmsg multishot command (Dylan)

 - Error handling fix for passthru (Anuj)

 - Remove randomization of struct kiocb fields, to avoid it growing in
   size if re-arranged in such a fashion that it grows more holes or
   padding (Keith, Linus)

 - Small series improving type safety of the sqe fields (Stefan)

* tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block:
  io_uring: add missing BUILD_BUG_ON() checks for new io_uring_sqe fields
  io_uring: make io_kiocb_to_cmd() typesafe
  fs: don't randomize struct kiocb fields
  io_uring: consistently make use of io_notif_to_data()
  io_uring: fix error handling for io_uring_cmd
  io_uring: fix io_recvmsg_prep_multishot sparse warnings
  io_uring/net: send retry for zerocopy
  io_uring: mem-account pbuf buckets
  audit, io_uring, io-wq: Fix memory leak in io_sq_thread() and io_wqe_worker()
  io_uring: pass correct parameters to io_req_set_res

This is a prelude to adding more tests to shell tests and in order to
support putting those tests into subdirectories, I need to change the
test code that scans/finds and runs them.

To support subdirs I have to recurse so it's time to refactor the code
to allow this and centralize the shell script finding into one location
and only one single scan that builds a list of all the found tests in
memory instead of it being duplicated in 3 places.

This code also optimizes things like knowing the max width of desciption
strings (as we can do that while we scan instead of a whole new pass of
opening files).

It also more cleanly filters scripts to see only *.sh files thus
skipping random other files in directories like *~ backup files, other
random junk/data files that may appear and the scripts must be
executable to make the cut (this ensures the script lib dir is not seen
as scripts to run).

This avoids perf test running previous older versions of test scripts
that are editor backup files as well as skipping perf.data files that
may appear and so on.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight@lists.linaro.org
Link: https://lore.kernel.org/r/20220812121641.336465-2-carsten.haitzler@foss.arm.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v1.20, update events for snowridgex by the latest
event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the snowridgex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-12-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>