- 24 Apr, 2020 25 commits
-
-
Yang Yingliang authored
The type of loaddr is u8 which is always '<=' 0xff, so the loaddr <= 0xff is always true, we can remove this comparison. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
commit 877d1f62 ("net: Set sk_txhash from a random number") left behind this, remove it. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
YueHaibing authored
There's no callers in-tree anymore. Signed-off-by:
-
Zheng Bin authored
Fixes coccicheck warning: drivers/net/ethernet/aquantia/atlantic/aq_macsec.c:404:2-3: Unneeded semicolon drivers/net/ethernet/aquantia/atlantic/aq_macsec.c:420:2-3: Unneeded semicolon Reported-by:
Zheng Bin <zhengbin13@huawei.com> Acked-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
-
Zheng Bin authored
Fixes coccicheck warning: drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c:79:2-3: Unneeded semicolon drivers/net/ethernet/mellanox/mlxfw/mlxfw_fsm.c:162:2-3: Unneeded semicolon Reported-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
David S. Miller authored
Heiner Kallweit says: ==================== net: phy: smaller phylib improvements Series with smaller improvements for suspend and soft-reset handling. ==================== Signed-off-by: -
Heiner Kallweit authored
If a soft reset is triggered whilst PHY is in power-down, then phydev->suspended will remain set. Seems we didn't face any issue yet caused by this, but better reset the suspended flag after soft reset. See also the following from 22.2.4.1.1 Resetting a PHY is accomplished by setting bit 0.15 to a logic one. This action shall set the status and control registers to their default states. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Heiner Kallweit authored
Since 6e2d85ec ("net: phy: Stop with excessive soft reset") we don't need genphy_no_soft_reset() any longer. Not setting callback soft_reset results in a no-op now. Signed-off-by:
-
Heiner Kallweit authored
Gently handle the case that phy_suspend() is called whilst PHY is in power-down. Signed-off-by:
-
Russell King authored
Move the callback into the phylink_config structure, rather than providing a callback to set this up. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Tested-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
David S. Miller authored
Jesper Dangaard Brouer says: ==================== Fix qdisc noop issue caused by driver and identify future bugs I've been very puzzled why networking on my NXP development board, using driver dpaa2-eth, stopped working when I updated the kernel version >= 5.3. The observable issue were that interface would drop all TX packets, because it had assigned the qdisc noop. This turned out the be a NIC driver bug, that would only get triggered when using sysctl net/core/default_qdisc=fq_codel. It was non-trivial to find out[1] this was driver related. Thus, this patchset besides fixing the driver bug, also helps end-user identify the issue. [1]: https://github.com/xdp-project/xdp-project/blob/master/areas/arm64/board_nxp_ls1088/nxp-board04-troubleshoot-qdisc.org ==================== Signed-off-by:
-
Jesper Dangaard Brouer authored
Drivers ndo_setup_tc call should return -EOPNOTSUPP, when it cannot support the qdisc type. Other return values will result in failing the qdisc setup. This lead to qdisc noop getting assigned, which will drop all TX packets on the interface. Fixes: ab1e6de2 ("dpaa2-eth: Add mqprio support") Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Tested-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by:
-
Jesper Dangaard Brouer authored
Help end-users of the 'tc' command to see if the drivers ndo_setup_tc function call fails. Troubleshooting when this happens is non-trivial (see full process here[1]), and results in net_device getting assigned the 'qdisc noop', which will drop all TX packets on the interface. [1]: https://github.com/xdp-project/xdp-project/blob/master/areas/arm64/board_nxp_ls1088/nxp-board04-troubleshoot-qdisc.orgSigned-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Mirroring cleanups This patch set contains various cleanups in SPAN (mirroring) code noticed by Amit and I while working on future enhancements in this area. No functional changes intended. Tested by current mirroring selftests. Patches #1-#2 from Amit reduce nesting in a certain function and rename a callback to a more meaningful name. Patch #3 removes debug prints that have little value. Patch #4 converts a reference count to 'refcount_t' in order to catch over/under flows. Patch #5 replaces a zero-length array with flexible-array member in order to get a compiler warning in case the flexible array does not occur last in the structure. ==================== Signed-off-by: -
Ido Schimmel authored
In a similar fashion to commit e99f8e7f ("mlxsw: Replace zero-length array with flexible-array member"), use a flexible-array member to get a compiler warning in case the flexible array does not occur last in the structure. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Ido Schimmel authored
'refcount_t' is very useful for catching over/under flows. Convert the SPAN agent objects to use it instead of 'int' for their reference count. Signed-off-by:
-
Ido Schimmel authored
To the best of my knowledge, these debug prints were never used. Remove them. Signed-off-by:
-
Amit Cohen authored
Use a more meaningful name for parms() function. Signed-off-by:
Amit Cohen <amitc@mellanox.com> Reviewed-by:
-
Amit Cohen authored
Use early return to avoid unnecessary nesting. Signed-off-by:
-
David S. Miller authored
Tonghao Zhang says: ==================== openvswitch: expand meter tables and fix bug The patch set expand or shrink the meter table when necessary. and other patches fix bug or improve codes. ==================== Signed-off-by: -
Tonghao Zhang authored
When setting the meter rate to 4+Gbps, there is an overflow, the meters don't work as expected. Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
Tonghao Zhang <xiangxia.m.yue@gmail.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Tonghao Zhang authored
Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
-
Tonghao Zhang authored
Before invoking the ovs_meter_cmd_reply_stats, "meter" was checked, so don't check it agin in that function. Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
-
Tonghao Zhang authored
Don't allow user to create meter unlimitedly, which may cause to consume a large amount of kernel memory. The max number supported is decided by physical memory and 20K meters as default. Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
-
Tonghao Zhang authored
In kernel datapath of Open vSwitch, there are only 1024 buckets of meter in one datapath. If installing more than 1024 (e.g. 8192) meters, it may lead to the performance drop. But in some case, for example, Open vSwitch used as edge gateway, there should be 20K at least, where meters used for IP address bandwidth limitation. [Open vSwitch userspace datapath has this issue too.] For more scalable meter, this patch use meter array instead of hash tables, and expand/shrink the array when necessary. So we can install more meters than before in the datapath. Introducing the struct *dp_meter_instance, it's easy to expand meter though changing the *ti point in the struct *dp_meter_table. Cc: Pravin B Shelar <pshelar@ovn.org> Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
-
- 23 Apr, 2020 15 commits
-
-
Colin Ian King authored
Currently the unsigned variable tmp is being checked for an negative error return from the call to bcm_phy_read_rdb and this can never be true since tmp is unsigned. Fix this by making tmp a plain int. Addresses-Coverity: ("Unsigned compared against 0") Fixes: 4406d36d ("net: phy: bcm54140: add hwmon support") Signed-off-by:Colin Ian King <colin.king@canonical.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
Zou Wei authored
Fix the following sparse warning: drivers/net/ethernet/qlogic/qed/qed_ll2.c:2334:20: warning: symbol 'll2_cbs' was not declared. Should it be static? Reported-by:
Zou Wei <zou_wei@huawei.com> Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by:
-
Xu Wang authored
Remove unnecassary casts in the argument to kfree. Signed-off-by:
Xu Wang <vulab@iscas.ac.cn> Signed-off-by:
-
David S. Miller authored
Grygorii Strashko says: ==================== net: ethernet: ti: cpts: add irq and HW_TS_PUSH events This is re-spin of patches to add CPSW IRQ and HW_TS_PUSH events support I've sent long time ago [1]. In this series, I've tried to restructure and split changes, and also add few additional optimizations comparing to initial RFC submission [1]. The HW_TS_PUSH events intended to serve for different timesync purposes on of which is to add PPS generation function, which can be implemented as below: +-----------------+ | Control | | application | +------->+ +----------+ | | | | | | | | | +-----------------+ | | | | | | PTP_EXTTS_REQUEST | | | | | +----------------------------------------------------------------+ | | Kernel +-------+----------+ +-------v--------+ | \dev\ptpX | | /sys/class/pwm/| | | | | +-------^----------+ +-------+--------+ | | | | | +-------v-------------------+ +-------+----------+ | | | CPTS driver | |pwm/pwm-omap-dmtimer.c | | | +---------------------------+ +-------^----------+ |clocksource/timer_ti_dm.c | | +-------+-------------------+ |HWx_TS_PUSH evt | +----------------------------------------------------------------+ | | HW +-------+----------+ +-------v--------+ | CPTS | | DMTimer | | | | | | HWx_TS_PUSH X<-----------------+ | | + | | +------------------+ +-------+--------+ | X timer4 As per my knowledge there is at least one public implemented above PPS generation schema from Tusori Tibor [2] based on initial HW_TS_PUSH enable submission[1]. And now there is work done by Lokesh Vutla <lokeshvutla@ti.com> published to enable PWM enable/improve PWM adjustment from user space [3][4][5]. Main changes comparing to initial submission: - TX timestamp processing deferred to ptp worker only - both CPTS IRQ and polling events processing supported to make it work for Keystone 2 also - switch to use new .gettimex64() interface - no DT updates as number of HWx_TS_PUSH inputs is static per HW Testing on am571x-idk/omap2plus_defconfig/+CONFIG_PREEMPT=y: 1) testing HW_TS_PUSH - enable pwm in DT pwm16: dmtimer-pwm { compatible = "ti,omap-dmtimer-pwm"; ti,timers = <&timer16>; #pwm-cells = <3>; }; - configure and start pwm echo 0 > /sys/class/pwm/pwmchip0/export echo 1000000000 > /sys/class/pwm/pwmchip0/pwm0/period echo 500000000 > /sys/class/pwm/pwmchip0/pwm0/duty_cycle echo 1 > /sys/class/pwm/pwmchip0/pwm0/enable - test HWx_TS_PUSH using Kernel selftest testptp application ./tools/testing/selftests/ptp/testptp -d /dev/ptp0 -e 1000 -i 3 2) testing phc2sys phc2sys[1616.791]: eth0 rms 408190379792180864 max 1580914543017209856 freq +864 +/- 4635 delay 645 +/- 29 phc2sys[1646.795]: eth0 rms 41 max 108 freq +0 +/- 36 delay 656 +/- 29 phc2sys[1676.800]: eth0 rms 43 max 83 freq +2 +/- 38 delay 650 +/- 0 phc2sys[1706.804]: eth0 rms 39 max 87 freq +4 +/- 34 delay 672 +/- 55 phc2sys[1736.808]: eth0 rms 35 max 66 freq +1 +/- 30 delay 667 +/- 49 phc2sys[1766.813]: eth0 rms 38 max 79 freq +2 +/- 33 delay 656 +/- 29 phc2sys[1796.817]: eth0 rms 45 max 98 freq +1 +/- 39 delay 656 +/- 29 phc2sys[1826.821]: eth0 rms 40 max 87 freq +5 +/- 35 delay 650 +/- 0 phc2sys[1856.826]: eth0 rms 29 max 76 freq -0 +/- 25 delay 656 +/- 29 phc2sys[1886.830]: eth0 rms 40 max 97 freq +4 +/- 35 delay 667 +/- 49 phc2sys[1916.834]: eth0 rms 42 max 94 freq +2 +/- 36 delay 661 +/- 41 phc2sys[1946.839]: eth0 rms 40 max 91 freq +2 +/- 35 delay 661 +/- 41 phc2sys[1976.843]: eth0 rms 46 max 88 freq -0 +/- 40 delay 667 +/- 49 phc2sys[2006.847]: eth0 rms 49 max 97 freq +2 +/- 43 delay 650 +/- 0 3) testing ptp4l - 1G connection ptp4l[862.891]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED ptp4l[923.894]: rms 1019697354682 max 5768279314068 freq +26053 +/- 72 delay 488 +/- 1 ptp4l[987.896]: rms 13 max 26 freq +26005 +/- 29 delay 488 +/- 1 ptp4l[1051.899]: rms 14 max 50 freq +25895 +/- 21 delay 488 +/- 1 ptp4l[1115.901]: rms 11 max 27 freq +25878 +/- 17 delay 488 +/- 1 ptp4l[1179.904]: rms 10 max 27 freq +25857 +/- 12 delay 488 +/- 1 ptp4l[1243.906]: rms 14 max 37 freq +25851 +/- 15 delay 488 +/- 1 ptp4l[1307.909]: rms 12 max 33 freq +25835 +/- 15 delay 488 +/- 1 ptp4l[1371.911]: rms 11 max 27 freq +25832 +/- 14 delay 488 +/- 1 ptp4l[1435.914]: rms 11 max 26 freq +25823 +/- 11 delay 488 +/- 1 ptp4l[1499.916]: rms 10 max 29 freq +25829 +/- 11 delay 489 +/- 1 ptp4l[1563.919]: rms 11 max 27 freq +25827 +/- 12 delay 488 +/- 1 - 10M connection ptp4l[51.955]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED ptp4l[112.957]: rms 279468848453933920 max 1580914542977391360 freq +25390 +/- 3207 delay 8222 +/- 36 ptp4l[176.960]: rms 254 max 522 freq +25809 +/- 219 delay 8271 +/- 30 ptp4l[240.962]: rms 271 max 684 freq +25868 +/- 234 delay 8249 +/- 22 ptp4l[304.965]: rms 263 max 556 freq +25894 +/- 227 delay 8225 +/- 47 ptp4l[368.967]: rms 238 max 648 freq +25908 +/- 204 delay 8234 +/- 40 ptp4l[432.970]: rms 274 max 658 freq +25932 +/- 237 delay 8241 +/- 22 ptp4l[496.972]: rms 247 max 557 freq +25943 +/- 213 delay 8223 +/- 26 ptp4l[560.974]: rms 291 max 756 freq +25968 +/- 251 delay 8244 +/- 41 ptp4l[624.977]: rms 249 max 697 freq +25975 +/- 216 delay 8258 +/- 22 Changes in v5: - fixed build issue Changes in v4: - fixed comments from Richard Cochran - dropped patch "net: ethernet: ti: cpts: move rx timestamp processing to ptp worker only" - added "Acked-by" from Richard Cochran <richardcochran@gmail.com> - dependencies resolved, patch merged Changes in v3: - fixed rebase mess - fixed build issues Changes in v2 (broken): - fixed (formatting) comments from David Miller <davem@davemloft.net> v4: https://patchwork.ozlabs.org/project/netdev/cover/20200422201254.15232-1-grygorii.strashko@ti.com/ v3: https://patchwork.ozlabs.org/project/netdev/cover/20200320194244.4703-1-grygorii.strashko@ti.com/ v2: https://patchwork.ozlabs.org/cover/1258339/ v1: https://patchwork.ozlabs.org/cover/1254708/ [1] https://lore.kernel.org/patchwork/cover/799251/ [2] https://usermanual.wiki/Document/SetupGuide.632280828.pdf https://github.com/t-tibor/msc_thesis [3] https://patchwork.kernel.org/cover/11421329/ [4] https://patchwork.kernel.org/cover/11433197/ [5] https://sourceforge.net/p/linuxptp/mailman/message/36943248/ ==================== Signed-off-by: -
Grygorii Strashko authored
The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This patch adds corresponding support to CPSW driver. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Grygorii Strashko authored
Hence CPTS IRQ support is in place the W_TS_PUSH events can be added. PWM capable DmTimers can be used to generete input signals for CPTS on TI AM335x/AM437x/DRA7 SoCs to be timestamped: AM335x/AM437x: timer4 - timer7 DRA7/AM57xx: timer13 - timer16 Signed-off-by:
-
Grygorii Strashko authored
Add CPTS IRQ support, but do not enable it. By default, the CPTS driver will continue working using polling mode which is required for CPTS to continue working on platforms other than CPSW, like Keystone 2. The CPTS IRQ support is required to enable support for HW_TS_PUSH events. The CPSW CPTS IRQ and HW_TS_PUSH events support will be enabled in follow up patches. Signed-off-by:
-
Grygorii Strashko authored
Now spinlock is used to synchronize everything which is not required. Add mutex and use to sync access to PTP interface and PTP worker and use spinlock only to sync FIFO/events processing. Signed-off-by:
-
Grygorii Strashko authored
Now the tx timestamp processing happens from different contexts - softirq and thread/PTP worker. Enabling IRQ will add one more hard_irq context. This makes over all defered TX timestamp processing and locking overcomplicated. Move tx timestamp processing to PTP worker always instead. napi_rx->cpts_tx_timestamp if ptp_packet then push to txq ptp_schedule_worker() do_aux_work->cpts_overflow_check cpts_process_events() Signed-off-by: -
Grygorii Strashko authored
Now the CPTS driver performs packet (skb) parsing every time when it needs to match packet to CPTS event (including ptp_classify_raw() calls). This patch optimizes matching process by parsing packet only once upon arrival and stores PTP specific data in skb->cb using the same fromat as in CPTS HW event. As result, all future matching reduces to comparing two u32 values. Signed-off-by:
-
Grygorii Strashko authored
The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH write to actually reach HW. Hence switch CPTS driver to implement new .gettimex64() callback for more precise measurement of the offset between a PHC and the system clock which is measured as time between write(CPSW_CPTS_PUSH) read(CPSW_CPTS_PUSH) Signed-off-by:
-
Grygorii Strashko authored
Now CPTS driver .adjfreq() generates request to read CPTS current time (CPTS_EV_PUSH) with intention to process all pending event using previous frequency adjustment values before switching to the new ones. So CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment values. Current code assumes that all job is done in .adjfreq(), but after enabling IRQ this will not be true any more. Hence save new frequency adjustment values (mult) and perform actual freq adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received. Signed-off-by:
-
Grygorii Strashko authored
Now CPTS HW time reading code is implemented in timecounter->cyclecounter .read() callback and performs following operations: timecounter_read() ->cc.read() -> cpts_systim_read() - request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1 - poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp This approach need to be changed for the future switch to PTP PHC .gettimex64() callback, which require to separate requesting current CPTS HW time and processing CPTS FIFO. And for the follow up patch, which improves .adjfreq() implementation. This patch moves code accessing CPTS HW out of timecounter code as following: - convert HW timestamp of every CPTS event to PTP time (us) and store it as part struct cpts_event; - add CPTS context field to store current CPTS HW time (counter) value and update it on CPTS_EV_PUSH reception; - move code accessing CPTS HW out of timecounter code and use current CPTS HW time (counter) from CPTS context instead; - ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception. After this change CPTS timecounter will only perform timekeeper role without actually accessing CPTS HW. Signed-off-by:
-
Grygorii Strashko authored
Use dev_yy() API instead of pr_yy() for log outputs. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== net: napi: addition of napi_defer_hard_irqs This patch series augments gro_glush_timeout feature with napi_defer_hard_irqs As extensively described in first patch changelog, this can suppresss the chit-chat traffic between NIC and host to signal interrupts and re-arming them, since this can be an issue on high speed NIC with many queues. The last patch in this series converts mlx4 TX completion to napi_complete_done(), to enable this new mechanism. ==================== Signed-off-by:
-
