Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled.  This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock.  Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.

This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Intermittent Kernel crash has been observed on probe in
bcm_qspi_mspi_l2_isr() handler when the MSPI spifie interrupt bit
has not been cleared before registering for interrupts.
Fix the driver to move SoC specific custom interrupt handling code
before we register IRQ in probe. Also clear MSPI interrupt status
resgiter prior to registering IRQ handlers.

Fixes: cc20a386 ("spi: iproc-qspi: Add Broadcom iProc SoCs support")
Signed-off-by: Kamal Dasu <kdasu@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211008203603.40915-3-kdasu.kdev@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In commit 7e71b854 ("arm64: dts: ls1028a: fix node name for the
sysclk") the sysclk node name was renamed and broke the erratum
workaround because it tries to fetch a device tree node by its name,
which is very fragile in general. We don't even need the sysclk node
because the only possible sysclk frequency input is 100MHz. In fact, the
erratum says it applies if SYS_PLL_RAT is 3, not that the platform clock
is 300 MHz. Make the workaround more reliable and just drop the unneeded
sysclk lookup.

For reference, the error during the bootup is the following:
[    4.898400] nxp-fspi 20c0000.spi: Errata cannot be executed. Read via IP bus may not work

Fixes: 82ce7d0e ("spi: spi-nxp-fspi: Implement errata workaround for LS1028A")
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211001212726.159437-1-michael@walle.ccSigned-off-by: Mark Brown <broonie@kernel.org>

In the function 'mtk_spi_set_hw_cs_timing'
the 'setup', 'hold' and 'inactive' delays are configured.
In case those values are 0 it causes errors on mt8173:

cros-ec-i2c-tunnel 1100a000.spi:ec@0:i2c-tunnel0:
	Error transferring EC i2c message -71
cros-ec-spi spi0.0: EC failed to respond in time.

This patch fixes that issues by setting only the values
that are not 0.

Fixes: 04e6bb0d ("spi: modify set_cs_timing parameter")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Link: https://lore.kernel.org/r/20211001152153.4604-1-dafna.hirschfeld@collabora.comSigned-off-by: Mark Brown <broonie@kernel.org>

atmel_spi_dma_map_xfer to never be called in PDC mode. This causes the
driver to silently fail.

This patch changes the conditional to match the behaviour of the
previous commit before the refactor.

Fixes: 5fa5e6de ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Ville Baillie <villeb@bytesnap.co.uk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210921072132.21831-1-villeb@bytesnap.co.ukSigned-off-by: Mark Brown <broonie@kernel.org>

Linux 5.15-rc3

Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.

Fixes: 96c8395e ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210923170023.1683-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Pull ksmbd fixes from Steve French:
 "Five fixes for the ksmbd kernel server, including three security
  fixes:

   - remove follow symlinks support

   - use LOOKUP_BENEATH to prevent out of share access

   - SMB3 compounding security fix

   - fix for returning the default streams correctly, fixing a bug when
     writing ppt or doc files from some clients

   - logging more clearly that ksmbd is experimental (at module load
     time)"

* tag '5.15-rc2-ksmbd-fixes' of git://git.samba.org/ksmbd:
  ksmbd: use LOOKUP_BENEATH to prevent the out of share access
  ksmbd: remove follow symlinks support
  ksmbd: check protocol id in ksmbd_verify_smb_message()
  ksmbd: add default data stream name in FILE_STREAM_INFORMATION
  ksmbd: log that server is experimental at module load

Pull EDAC fixes from Borislav Petkov:
 "Fix two EDAC drivers using the wrong value type for the DIMM mode"

* tag 'edac_urgent_for_v5.15_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/dmc520: Assign the proper type to dimm->edac_mode
  EDAC/synopsys: Fix wrong value type assignment for edac_mode

Pull thermal fixes from Daniel Lezcano:

 - Fix thermal shutdown after a suspend/resume due to a wrong TCC value
   restored on Intel platform (Antoine Tenart)

 - Fix potential buffer overflow when building the list of policies. The
   buffer size is not updated after writing to it (Dan Carpenter)

 - Fix wrong check against IS_ERR instead of NULL (Ansuel Smith)

* tag 'thermal-v5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
  thermal/drivers/tsens: Fix wrong check for tzd in irq handlers
  thermal/core: Potential buffer overflow in thermal_build_list_of_policies()
  thermal/drivers/int340x: Do not set a wrong tcc offset on resume

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Prevent sending the wrong signal when protection keys are enabled
     and the kernel handles a fault in the vsyscall emulation.

   - Invoke early_reserve_memory() before invoking e820_memory_setup()
     which is required to make the Xen dom0 e820 hooks work correctly.

   - Use the correct data type for the SETZ operand in the EMQCMDS
     instruction wrapper.

   - Prevent undefined behaviour to the potential unaligned accesss in
     the instruction decoder library"

* tag 'x86-urgent-2021-09-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/insn, tools/x86: Fix undefined behavior due to potential unaligned accesses
  x86/asm: Fix SETZ size enqcmds() build failure
  x86/setup: Call early_reserve_memory() earlier
  x86/fault: Fix wrong signal when vsyscall fails with pkey

Pull timer fix from Thomas Gleixner:
 "A single fix for the recently introduced regression in posix CPU
  timers which failed to stop the timer when requested. That caused
  unexpected signals to be sent to the process/thread causing
  malfunction"

* tag 'timers-urgent-2021-09-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Prevent spuriously armed 0-value itimer

Pull irq fixes from Thomas Gleixner:
 "A set of fixes for interrupt chip drivers:

   - Work around a bad GIC integration on a Renesas platform which can't
     handle byte-sized MMIO access

   - Plug a potential memory leak in the GICv4 driver

   - Fix a regression in the Armada 370-XP IPI code which was caused by
     issuing EOI instack of ACK.

   - A couple of small fixes here and there"

* tag 'irq-urgent-2021-09-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic: Work around broken Renesas integration
  irqchip/renesas-rza1: Use semicolons instead of commas
  irqchip/gic-v3-its: Fix potential VPE leak on error
  irqchip/goldfish-pic: Select GENERIC_IRQ_CHIP to fix build
  irqchip/mbigen: Repair non-kernel-doc notation
  irqdomain: Change the type of 'size' in __irq_domain_add() to be consistent
  irqchip/armada-370-xp: Fix ack/eoi breakage
  Documentation: Fix irq-domain.rst build warning

Merge misc fixes from Andrew Morton:
 "16 patches.

  Subsystems affected by this patch series: xtensa, sh, ocfs2, scripts,
  lib, and mm (memory-failure, kasan, damon, shmem, tools, pagecache,
  debug, and pagemap)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: fix uninitialized use in overcommit_policy_handler
  mm/memory_failure: fix the missing pte_unmap() call
  kasan: always respect CONFIG_KASAN_STACK
  sh: pgtable-3level: fix cast to pointer from integer of different size
  mm/debug: sync up latest migrate_reason to migrate_reason_names
  mm/debug: sync up MR_CONTIG_RANGE and MR_LONGTERM_PIN
  mm: fs: invalidate bh_lrus for only cold path
  lib/zlib_inflate/inffast: check config in C to avoid unused function warning
  tools/vm/page-types: remove dependency on opt_file for idle page tracking
  scripts/sorttable: riscv: fix undeclared identifier 'EM_RISCV' error
  ocfs2: drop acl cache for directories too
  mm/shmem.c: fix judgment error in shmem_is_huge()
  xtensa: increase size of gcc stack frame check
  mm/damon: don't use strnlen() with known-bogus source length
  kasan: fix Kconfig check of CC_HAS_WORKING_NOSANITIZE_ADDRESS
  mm, hwpoison: add is_free_buddy_page() in HWPoisonHandlable()

Pull SCSI fixes from James Bottomley:
 "Thirty-three fixes, I'm afraid.

  Essentially the build up from the last couple of weeks while I've been
  dealling with Linux Plumbers conference infrastructure issues. It's
  mostly the usual assortment of spelling fixes and minor corrections.

  The only core relevant changes are to the sd driver to reduce the spin
  up message spew and fix a small memory leak on the freeing path"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (33 commits)
  scsi: ses: Retry failed Send/Receive Diagnostic commands
  scsi: target: Fix spelling mistake "CONFLIFT" -> "CONFLICT"
  scsi: lpfc: Fix gcc -Wstringop-overread warning, again
  scsi: lpfc: Use correct scnprintf() limit
  scsi: lpfc: Fix sprintf() overflow in lpfc_display_fpin_wwpn()
  scsi: core: Remove 'current_tag'
  scsi: acornscsi: Remove tagged queuing vestiges
  scsi: fas216: Kill scmd->tag
  scsi: qla2xxx: Restore initiator in dual mode
  scsi: ufs: core: Unbreak the reset handler
  scsi: sd_zbc: Support disks with more than 2**32 logical blocks
  scsi: ufs: core: Revert "scsi: ufs: Synchronize SCSI and UFS error handling"
  scsi: bsg: Fix device unregistration
  scsi: sd: Make sd_spinup_disk() less noisy
  scsi: ufs: ufs-pci: Fix Intel LKF link stability
  scsi: mpt3sas: Clean up some inconsistent indenting
  scsi: megaraid: Clean up some inconsistent indenting
  scsi: sr: Fix spelling mistake "does'nt" -> "doesn't"
  scsi: Remove SCSI CDROM MAINTAINERS entry
  scsi: megaraid: Fix Coccinelle warning
  ...

Pull io_uring fixes from Jens Axboe:
 "This one looks a bit bigger than it is, but that's mainly because 2/3
  of it is enabling IORING_OP_CLOSE to close direct file descriptors.

  We've had a few folks using them and finding it confusing that the way
  to close them is through using -1 for file update, this just brings
  API symmetry for direct descriptors. Hence I think we should just do
  this now and have a better API for 5.15 release. There's some room for
  de-duplicating the close code, but we're leaving that for the next
  merge window.

  Outside of that, just small fixes:

   - Poll race fixes (Hao)

   - io-wq core dump exit fix (me)

   - Reschedule around potentially intensive tctx and buffer iterators
     on teardown (me)

   - Fix for always ending up punting files update to io-wq (me)

   - Put the provided buffer meta data under memcg accounting (me)

   - Tweak for io_write(), removing dead code that was added with the
     iterator changes in this release (Pavel)"

* tag 'io_uring-5.15-2021-09-25' of git://git.kernel.dk/linux-block:
  io_uring: make OP_CLOSE consistent with direct open
  io_uring: kill extra checks in io_write()
  io_uring: don't punt files update to io-wq unconditionally
  io_uring: put provided buffer meta data under memcg accounting
  io_uring: allow conditional reschedule for intensive iterators
  io_uring: fix potential req refcount underflow
  io_uring: fix missing set of EPOLLONESHOT for CQ ring overflow
  io_uring: fix race between poll completion and cancel_hash insertion
  io-wq: ensure we exit if thread group is exiting

Pull block fixes from Jens Axboe:

 - NVMe pull request via Christoph:
      - keep ctrl->namespaces ordered (Christoph Hellwig)
      - fix incorrect h2cdata pdu offset accounting in nvme-tcp (Sagi
        Grimberg)
      - handled updated hw_queues in nvme-fc more carefully (Daniel
        Wagner, James Smart)

 - md lock order fix (Christoph)

 - fallocate locking fix (Ming)

 - blktrace UAF fix (Zhihao)

 - rq-qos bio tracking fix (Ming)

* tag 'block-5.15-2021-09-25' of git://git.kernel.dk/linux-block:
  block: hold ->invalidate_lock in blkdev_fallocate
  blktrace: Fix uaf in blk_trace access after removing by sysfs
  block: don't call rq_qos_ops->done_bio if the bio isn't tracked
  md: fix a lock order reversal in md_alloc
  nvme: keep ctrl->namespaces ordered
  nvme-tcp: fix incorrect h2cdata pdu offset accounting
  nvme-fc: remove freeze/unfreeze around update_nr_hw_queues
  nvme-fc: avoid race between time out and tear down
  nvme-fc: update hardware queues before using them

Pull xen fixes from Juergen Gross:
 "Some minor cleanups and fixes of some theoretical bugs, as well as a
  fix of a bug introduced in 5.15-rc1"

* tag 'for-linus-5.15b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/x86: fix PV trap handling on secondary processors
  xen/balloon: fix balloon kthread freezing
  swiotlb-xen: this is PV-only on x86
  xen/pci-swiotlb: reduce visibility of symbols
  PCI: only build xen-pcifront in PV-enabled environments
  swiotlb-xen: ensure to issue well-formed XENMEM_exchange requests
  Xen/gntdev: don't ignore kernel unmapping error
  xen/x86: drop redundant zeroing from cpu_initialize_context()

Merge tag 'linux-kselftest-fixes-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:

 - fix to Kselftest common framework header install to run before other
   targets for it work correctly in parallel build case.

 - fixes to kvm test to not ignore fscanf() returns which could result
   in inconsistent test behavior and failures.

* tag 'linux-kselftest-fixes-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: kvm: fix get_run_delay() ignoring fscanf() return warn
  selftests: kvm: move get_run_delay() into lib/test_util
  selftests:kvm: fix get_trans_hugepagesz() ignoring fscanf() return warn
  selftests:kvm: fix get_warnings_count() ignoring fscanf() return warn
  selftests: be sure to make khdr before other targets

Pull erofs fixes from Gao Xiang:
 "Two bugfixes to fix the 4KiB blockmap chunk format availability and a
  dangling pointer usage. There is also a trivial cleanup to clarify
  compacted_2b if compacted_4b_initial > totalidx.

  Summary:

   - fix the dangling pointer use in erofs_lookup tracepoint

   - fix unsupported chunk format check

   - zero out compacted_2b if compacted_4b_initial > totalidx"

* tag 'erofs-for-5.15-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: clear compacted_2b if compacted_4b_initial > totalidx
  erofs: fix misbehavior of unsupported chunk format check
  erofs: fix up erofs_lookup tracepoint

Pull cifs fixes from Steve French:
 "Six small cifs/smb3 fixes, two for stable:

   - important fix for deferred close (found by a git functional test)
     related to attribute caching on close.

   - four (two cosmetic, two more serious) small fixes for problems
     pointed out by smatch via Dan Carpenter

   - fix for comment formatting problems pointed out by W=1"

* tag '5.15-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix incorrect check for null pointer in header_assemble
  smb3: correct server pointer dereferencing check to be more consistent
  smb3: correct smb3 ACL security descriptor
  cifs: Clear modified attribute bit from inode flags
  cifs: Deal with some warnings from W=1
  cifs: fix a sign extension bug

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.15-rc3.

  Nothing huge in here, just fixes for a number of small issues that
  have been reported. These include:

   - habanalabs race conditions and other bugs fixed

   - binder driver fixes

   - fpga driver fixes

   - coresight build warning fix

   - nvmem driver fix

   - comedi memory leak fix

   - bcm-vk tty race fix

   - other tiny driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  comedi: Fix memory leak in compat_insnlist()
  nvmem: NVMEM_NINTENDO_OTP should depend on WII
  misc: bcm-vk: fix tty registration race
  fpga: dfl: Avoid reads to AFU CSRs during enumeration
  fpga: machxo2-spi: Fix missing error code in machxo2_write_complete()
  fpga: machxo2-spi: Return an error on failure
  habanalabs: expose a single cs seq in staged submissions
  habanalabs: fix wait offset handling
  habanalabs: rate limit multi CS completion errors
  habanalabs/gaudi: fix LBW RR configuration
  habanalabs: Fix spelling mistake "FEADBACK" -> "FEEDBACK"
  habanalabs: fail collective wait when not supported
  habanalabs/gaudi: use direct MSI in single mode
  habanalabs: fix kernel OOPs related to staged cs
  habanalabs: fix potential race in interrupt wait ioctl
  mcb: fix error handling in mcb_alloc_bus()
  misc: genwqe: Fixes DMA mask setting
  coresight: syscfg: Fix compiler warning
  nvmem: core: Add stubs for nvmem_cell_read_variable_le_u32/64 if !CONFIG_NVMEM
  binder: make sure fd closes complete
  ...

Pull staging driver fixes from Greg KH:
 "Here are two small staging driver fixes for 5.15-rc3:

   - greybus tty use-after-free bugfix

   - r8188eu ioctl overlap build warning fix

  Note, the r8188eu ioctl has been entirely removed for 5.16-rc1, but
  it's good to get this fixed now for people using this in 5.15.

  Both of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: fix -Wrestrict warnings
  staging: greybus: uart: fix tty use after free

Pull tty/serial fixes from Greg KH:
 "Here are four small tty/serial driver fixes for 5.15-rc3. They
  include:

   - remove an export now that no one is using it anymore

   - mvebu-uart tx_empty callback fix

   - 8250_omap bugfix

   - synclink_gt build fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: unexport tty_ldisc_release
  tty: synclink_gt: rename a conflicting function name
  serial: mvebu-uart: fix driver's tx_empty callback
  serial: 8250: 8250_omap: Fix RX_LVL register offset

Pull USB driver fixes from Greg KH:
 "Here are some USB driver fixes and new device ids for 5.15-rc3.

  They include:

   - usb-storage quirk additions

   - usb-serial new device ids

   - usb-serial driver fixes

   - USB roothub registration bugfix to resolve a long-reported issue

   - usb gadget driver fixes for a large number of small things

   - dwc2 driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits)
  USB: serial: option: add device id for Foxconn T99W265
  USB: serial: cp210x: add ID for GW Instek GDM-834x Digital Multimeter
  USB: serial: cp210x: add part-number debug printk
  USB: serial: cp210x: fix dropped characters with CP2102
  MAINTAINERS: usb, update Peter Korsgaard's entries
  usb: musb: tusb6010: uninitialized data in tusb_fifo_write_unaligned()
  usb-storage: Add quirk for ScanLogic SL11R-IDE older than 2.6c
  Re-enable UAS for LaCie Rugged USB3-FW with fk quirk
  USB: serial: option: remove duplicate USB device ID
  USB: serial: mos7840: remove duplicated 0xac24 device ID
  arm64: dts: qcom: ipq8074: remove USB tx-fifo-resize property
  usb: gadget: f_uac2: Populate SS descriptors' wBytesPerInterval
  usb: gadget: f_uac2: Add missing companion descriptor for feedback EP
  usb: dwc2: gadget: Fix ISOC transfer complete handling for DDMA
  usb: core: hcd: Modularize HCD stop configuration in usb_stop_hcd()
  xhci: Set HCD flag to defer primary roothub registration
  usb: core: hcd: Add support for deferring roothub registration
  usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave
  usb: dwc3: core: balance phy init and exit
  Revert "USB: bcma: Add a check for devm_gpiod_get"
  ...

instead of removing '..' in a given path, call
kern_path with LOOKUP_BENEATH flag to prevent
the out of share access.

ran various test on this:
smb2-cat-async smb://127.0.0.1/homes/../out_of_share
smb2-cat-async smb://127.0.0.1/homes/foo/../../out_of_share
smbclient //127.0.0.1/homes -c "mkdir ../foo2"
smbclient //127.0.0.1/homes -c "rename bar ../bar"

Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Ralph Boehme <slow@samba.org>
Tested-by: Steve French <smfrench@gmail.com>
Tested-by: Namjae Jeon <linkinjeon@kernel.org>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

We get an unexpected value of /proc/sys/vm/overcommit_memory after
running the following program:

  int main()
  {
      int fd = open("/proc/sys/vm/overcommit_memory", O_RDWR);
      write(fd, "1", 1);
      write(fd, "2", 1);
      close(fd);
  }

write(fd, "2", 1) will pass *ppos = 1 to proc_dointvec_minmax.
proc_dointvec_minmax will return 0 without setting new_policy.

  t.data = &new_policy;
  ret = proc_dointvec_minmax(&t, write, buffer, lenp, ppos)
      -->do_proc_dointvec
         -->__do_proc_dointvec
              if (write) {
                if (proc_first_pos_non_zero_ignore(ppos, table))
                  goto out;

  sysctl_overcommit_memory = new_policy;

so sysctl_overcommit_memory will be set to an uninitialized value.

Check whether new_policy has been changed by proc_dointvec_minmax.

Link: https://lkml.kernel.org/r/20210923020524.13289-1-chenjun102@huawei.com
Fixes: 56f3547b ("mm: adjust vm_committed_as_batch according to vm overcommit policy")
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Feng Tang <feng.tang@intel.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Rui Xiang <rui.xiang@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The paired pte_unmap() call is missing before the
dev_pagemap_mapping_shift() returns.  So fix it.

David says:
 "I guess this code never runs on 32bit / highmem, that's why we didn't
  notice so far".

[akpm@linux-foundation.org: cleanup]

Link: https://lkml.kernel.org/r/20210923122642.4999-1-zhengqi.arch@bytedance.comSigned-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, the asan-stack parameter is only passed along if
CFLAGS_KASAN_SHADOW is not empty, which requires KASAN_SHADOW_OFFSET to
be defined in Kconfig so that the value can be checked.  In RISC-V's
case, KASAN_SHADOW_OFFSET is not defined in Kconfig, which means that
asan-stack does not get disabled with clang even when CONFIG_KASAN_STACK
is disabled, resulting in large stack warnings with allmodconfig:

  drivers/video/fbdev/omap2/omapfb/displays/panel-lgphilips-lb035q02.c:117:12: error: stack frame size (14400) exceeds limit (2048) in function 'lb035q02_connect' [-Werror,-Wframe-larger-than]
  static int lb035q02_connect(struct omap_dss_device *dssdev)
             ^
  1 error generated.

Ensure that the value of CONFIG_KASAN_STACK is always passed along to
the compiler so that these warnings do not happen when
CONFIG_KASAN_STACK is disabled.

Link: https://github.com/ClangBuiltLinux/linux/issues/1453
References: 6baec880 ("kasan: turn off asan-stack for clang-8 and earlier")
Link: https://lkml.kernel.org/r/20210922205525.570068-1-nathan@kernel.orgSigned-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If X2TLB=y (CPU_SHX2=y or CPU_SHX3=y, e.g. migor_defconfig), pgd_t.pgd
is "unsigned long long", causing:

    In file included from arch/sh/include/asm/pgtable.h:13,
		     from include/linux/pgtable.h:6,
		     from include/linux/mm.h:33,
		     from arch/sh/kernel/asm-offsets.c:14:
    arch/sh/include/asm/pgtable-3level.h: In function `pud_pgtable':
    arch/sh/include/asm/pgtable-3level.h:37:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
       37 |  return (pmd_t *)pud_val(pud);
	  |         ^

Fix this by adding an intermediate cast to "unsigned long", which is
basically what the old code did before.

Link: https://lkml.kernel.org/r/2c2eef3c9a2f57e5609100a4864715ccf253d30f.1631713483.git.geert+renesas@glider.be
Fixes: 9cf6fa24 ("mm: rename pud_page_vaddr to pud_pgtable and make it return pmd_t *")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Daniel Palmer <daniel@thingy.jp>
Acked-by: Rob Landley <rob@landley.net>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Cc: Rich Felker <dalias@libc.org>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sync up MR_DEMOTION to migrate_reason_names and add a synch prompt.

Link: https://lkml.kernel.org/r/20210921064553.293905-3-o451686892@gmail.com
Fixes: 26aa2d19 ("mm/migrate: demote pages during reclaim")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mina Almasry <almasrymina@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Wei Xu <weixugc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sync up MR_CONTIG_RANGE and MR_LONGTERM_PIN to migrate_reason_names.

Link: https://lkml.kernel.org/r/20210921064553.293905-2-o451686892@gmail.com
Fixes: 31025351 ("mm/migrate: rename migration reason MR_CMA to MR_CONTIG_RANGE")
Fixes: d1e153fe ("mm/gup: migrate pinned pages out of movable zone")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mina Almasry <almasrymina@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Wei Xu <weixugc@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kernel test robot reported the regression of fio.write_iops[1] with
commit 8cc621d2 ("mm: fs: invalidate BH LRU during page migration").

Since lru_add_drain is called frequently, invalidate bh_lrus there could
increase bh_lrus cache miss ratio, which needs more IO in the end.

This patch moves the bh_lrus invalidation from the hot path( e.g.,
zap_page_range, pagevec_release) to cold path(i.e., lru_add_drain_all,
lru_cache_disable).

Zhengjun Xing confirmed
 "I test the patch, the regression reduced to -2.9%"

[1] https://lore.kernel.org/lkml/20210520083144.GD14190@xsang-OptiPlex-9020/
[2] 8cc621d2, mm: fs: invalidate BH LRU during page migration

Link: https://lkml.kernel.org/r/20210907212347.1977686-1-minchan@kernel.orgSigned-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: kernel test robot <oliver.sang@intel.com>
Reviewed-by: Chris Goldsworthy <cgoldswo@codeaurora.org>
Tested-by: "Xing, Zhengjun" <zhengjun.xing@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Building Linux for ppc64le with Ubuntu clang version
12.0.0-3ubuntu1~21.04.1 shows the warning below.

    arch/powerpc/boot/inffast.c:20:1: warning: unused function 'get_unaligned16' [-Wunused-function]
    get_unaligned16(const unsigned short *p)
    ^
    1 warning generated.

Fix it by moving the check from the preprocessor to C, so the compiler
sees the use.

Link: https://lkml.kernel.org/r/20210920084332.5752-1-pmenzel@molgen.mpg.deSigned-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Idle page tracking can also be used for process address space, not only
file mappings.

Without this change, using with '-i' option for process address space
encounters below errors reported.

  $ sudo ./page-types -p $(pidof bash) -i
  mark page idle: Bad file descriptor
  mark page idle: Bad file descriptor
  mark page idle: Bad file descriptor
  mark page idle: Bad file descriptor
  ...

Link: https://lkml.kernel.org/r/20210917032826.10669-1-changbin.du@gmail.comSigned-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the following build failure reported in [1] by adding a conditional
definition of EM_RISCV in order to allow cross-compilation on machines
which do not have EM_RISCV definition in their host.

   scripts/sorttable.c:352:7: error: use of undeclared identifier 'EM_RISCV'

EM_RISCV was added to <elf.h> in glibc 2.24 so builds on systems with
glibc headers < 2.24 should show this error.

[mkubecek@suse.cz: changelog addition]
Link: https://lore.kernel.org/lkml/e8965b25-f15b-c7b4-748c-d207dda9c8e8@i2se.com/ [1]
Link: https://lkml.kernel.org/r/20210913030625.4525-1-miles.chen@mediatek.com
Fixes: 54fed35f ("riscv: Enable BUILDTIME_TABLE_SORT")
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Cc: Michal Kubecek <mkubecek@suse.cz>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ocfs2_data_convert_worker() is currently dropping any cached acl info
for FILE before down-converting meta lock.  It should also drop for
DIRECTORY.  Otherwise the second acl lookup returns the cached one (from
VFS layer) which could be already stale.

The problem we are seeing is that the acl changes on one node doesn't
get refreshed on other nodes in the following case:

  Node 1                    Node 2
  --------------            ----------------
  getfacl dir1

                            getfacl dir1    <-- this is OK

  setfacl -m u:user1:rwX dir1
  getfacl dir1   <-- see the change for user1

                            getfacl dir1    <-- can't see change for user1

Link: https://lkml.kernel.org/r/20210903012631.6099-1-wen.gang.wang@oracle.comSigned-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In the case of SHMEM_HUGE_WITHIN_SIZE, the page index is not rounded up
correctly.  When the page index points to the first page in a huge page,
round_up() cannot bring it to the end of the huge page, but to the end
of the previous one.

An example:

HPAGE_PMD_NR on my machine is 512(2 MB huge page size).  After
allcoating a 3000 KB buffer, I access it at location 2050 KB.  In
shmem_is_huge(), the corresponding index happens to be 512.  After
rounded up by HPAGE_PMD_NR, it will still be 512 which is smaller than
i_size, and shmem_is_huge() will return true.  As a result, my buffer
takes an additional huge page, and that shouldn't happen when
shmem_enabled is set to within_size.

Link: https://lkml.kernel.org/r/20210909032007.18353-1-liuyuntao10@huawei.com
Fixes: f3f0e1d2 ("khugepaged: add support of collapse for tmpfs/shmem pages")
Signed-off-by: Liu Yuntao <liuyuntao10@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: wuxu.wu <wuxu.wu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

xtensa frame size is larger than the frame size for almost all other
architectures.  This results in more than 50 "the frame size of <n> is
larger than 1024 bytes" errors when trying to build xtensa:allmodconfig.

Increase frame size for xtensa to 1536 bytes to avoid compile errors due
to frame size limits.

Link: https://lkml.kernel.org/r/20210912025235.3514761-1-linux@roeck-us.netSigned-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>