- 05 May, 2007 40 commits
-
-
Sergei Shtylyov authored
Fix the multiword DMA and drop the single-word DMA support (which nobody will miss, I think). In order to do it, a number of changes was necessary: - rename program_drive_counts() to program_cycle_times(), pass to it cycle's total/active times instead of the clock counts, and convert them into the active/recovery clocks there instead of cmd64x_tune_pio() -- this causes quantize_timing() to also move; - contrarywise, move all the code handling the address setup timing into cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup; - remove from the speedproc() method the bogus code pretending to set the DMA timings by twiddling bits in the BMIDE status register, handle setting MWDMA by just calling program_cycle_times(); while at it, improve the style of that whole switch statement; - stop fiddling with the DMA capable bits in the speedproc() method -- they do not enable DMA, and are properly dealt with by the dma_host_{on,off} methods; - don't set hwif->swdma_mask in the init_hwif() method anymore. In addition to those changes, do the following: - in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt status bit, eliminate local_irq_{save|restore}() around this code as there's *no* actual race with the interrupt handler, and move cmdprintk() to a more fitting place -- after ide_get_best_pio_mode() call; - make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn; - rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[]; - in the speedproc() method, get rid of the duplicate reads/writes from/to the UDIDETCRx registers and of the extra variable used to store the transfer mode value after filtering, use another method of determining master/slave drive, and cleanup useless parens; - beautify cmdprintk() output here and there. While at it, remove meaningless comment about the driver being used only on UltraSPARC and long non-relevant RCS tag. :-) Signed-off-by:Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Sergei Shtylyov authored
Fold the now equivalent code in the ide_dma_check() method into a mere call to ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set and call it from the ide_dma_check() method instead of ide_dma_on(). Defer writing the DMA timings to the chip registers until DMA is really turned on (and do not enable IORDY for DMA). Remove unneeded code from the init_hwif() method, improve its overall looks. Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and also use more proper hwif->dma_command, fix printk() and comment in the latter one as well. While at it, cleanup style in several places. Signed-off-by:
-
Sergei Shtylyov authored
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this driver by storing the PIO mode timings in the 'drive_data' instead -- this allows us to greatly simplify the process of "reloading" of the chip's timing register and do it right in sl82c150_dma_off_quietly() and to get rid of two extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio() and now returns a PIO mode selected, with ide_config_drive_speed() call moved into the tuneproc() method, now called sl82c105_tune_drive() with the code to set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place in the init_hwif() method. Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get rid of the code in it clamping cycle counts to 32 which was both incorrect and never executed anyway... Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmcLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (46 commits) mmc-omap: Clean up omap set_ios and make MMC_POWER_ON work mmc-omap: Fix omap to use MMC_POWER_ON mmc-omap: add missing '\n' mmc: make tifm_sd_set_dma_data() static mmc: remove old card states mmc: support unsafe resume of cards mmc: separate out reading EXT_CSD mmc: break apart switch function MMC: Fix handling of low-voltage cards MMC: Consolidate voltage definitions mmc: add bus handler wbsd: check for data opcode earlier mmc: Separate out protocol ops mmc: Move core functions to subdir mmc: deprecate mmc bus topology mmc: remove card upon suspend mmc: allow suspended block driver to be removed mmc: Flush pending detects on host removal mmc: Move host and card drivers to subdirs mmc: Move queue functions to mmc_block ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: ocfs2: Force use of GFP_NOFS in ocfs2_write() ocfs2: fix sparse warnings in fs/ocfs2/cluster ocfs2: fix sparse warnings in fs/ocfs2/dlm ocfs2: fix sparse warnings in fs/ocfs2 [PATCH] Copy i_flags to ocfs2 inode flags on write [PATCH] ocfs2: use __set_current_state() ocfs2: Wrap access of directory allocations with ip_alloc_sem. [PATCH] fs/ocfs2/: make 3 functions static ocfs2: Implement compat_ioctl()
-
Linus Torvalds authored
We used to BUG_ON() for a badly mapped IO port, which is certainly correct, but actually made it harder to debug the case where the ATA drivers had incorrectly mapped a nonconnected ATA port. So make badly mapped ports trigger a WARN_ON(), and throw the IO away instead (and return all ones for reads). For things like broken driver initialization - which is the most likely cause anyway - that should mean that the machine comes up and is usable (at least that was the case for the ATA breakage that triggered this patch). It tends to be a whole lot easier to do a "dmesg" on a working machine than to try to capture logs off a dead one. Signed-off-by:Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.linux-nfs.org/pub/linux/nfs-2.6Linus Torvalds authored
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (28 commits) NFS: Fix a compile glitch on 64-bit systems NFS: Clean up nfs_create_request comments spkm3: initialize hash spkm3: remove bad kfree, unnecessary export spkm3: fix spkm3's use of hmac NFS4: invalidate cached acl on setacl NFS: Fix directory caching problem - with test case and patch. NFS: Set meaningful value for fattr->time_start in readdirplus results. NFS: Added support to turn off the NFSv3 READDIRPLUS RPC. SUNRPC: RPC client should retry with different versions of rpcbind SUNRPC: remove old portmapper NFS: switch NFSROOT to use new rpcbind client SUNRPC: switch the RPC server to use the new rpcbind registration API SUNRPC: switch socket-based RPC transports to use rpcbind SUNRPC: introduce rpcbind: replacement for in-kernel portmapper SUNRPC: Eliminate side effects from rpc_malloc SUNRPC: RPC buffer size estimates are too large NLM: Shrink the maximum request size of NLM4 requests NFS: Use pgoff_t in structures and functions that pass page cache offsets NFS: Clean up nfs_sync_mapping_wait() ...
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits) [SCTP]: Set assoc_id correctly during INIT collision. [SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv() [SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP. [SCTP]: Verify all destination ports in sctp_connectx. [XFRM] SPD info TLV aggregation [XFRM] SAD info TLV aggregationx [AF_RXRPC]: Sort out MTU handling. [AF_IUCV/IUCV] : Add missing section annotations [AF_IUCV]: Implementation of a skb backlog queue [NETLINK]: Remove bogus BUG_ON [IPV6]: Some cleanups in include/net/ipv6.h [TCP]: zero out rx_opt in tcp_disconnect() [BNX2]: Fix TSO problem with small MSS. [NET]: Rework dev_base via list_head (v3) [TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start [BNX2]: Update version and reldate. [BNX2]: Print bus information for PCIE devices. [BNX2]: Add 1-shot MSI handler for 5709. [BNX2]: Restructure PHY event handling. [BNX2]: Add indirect spinlock. ...
-
Linus Torvalds authored
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits) Input: gpio_keys - add support for switches (EV_SW) Input: cobalt_btns - convert to use polldev library Input: add skeleton for simple polled devices Input: update some documentation Input: wistron - fix typo in keymap for Acer TM610 Input: add input_set_capability() helper Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs Input: i8042 - add Panasonic CF-29 to nomux list Input: lifebook - split into 2 devices Input: lifebook - add signature of Panasonic CF-29 Input: lifebook - activate 6-byte protocol on select models Input: lifebook - work properly on Panasonic CF-18 Input: cobalt buttons - separate device and driver registration Input: ati_remote - make button repeat sensitivity configurable Input: pxa27x - do not use deprecated SA_INTERRUPT flag Input: ucb1400 - make delays configurable Input: misc devices - switch to using input_dev->dev.parent Input: joysticks - switch to using input_dev->dev.parent Input: touchscreens - switch to using input_dev->dev.parent Input: mice - switch to using input_dev->dev.parent ... Fixed up conflicts with core device model removal of "struct subsystem" manually. Signed-off-by: -
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: remove "struct subsystem" as it is no longer needed sysfs: printk format warning DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt platform: reorder platform_device_del Driver core: fix show_uevent from taking up way too much stack
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits) PCI: Free resource files in error path of pci_create_sysfs_dev_files() pci-quirks: disable MSI on RS400-200 and RS480 PCI hotplug: Use menuconfig objects PCI: ZT5550 CPCI Hotplug driver fix PCI: rpaphp: Remove semaphores PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically PCI: rpaphp: Document is_php_dn() PCI: rpaphp: Document find_php_slot() PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot() PCI: rpaphp: refactor tail call to rpaphp_register_slot() PCI: rpaphp: remove rpaphp_set_attention_status() PCI: rpaphp: remove print_slot_pci_funcs() PCI: rpaphp: Remove setup_pci_slot() PCI: rpaphp: remove a call that does nothing but a pointer lookup PCI: rpaphp: Remove another wrappered function PCI: rpaphp: Remve another call that is a wrapper PCI: rpaphp: remove a function that does nothing but wrap debug printks PCI: rpaphp: Remove un-needed goto PCI: rpaphp: Fix a memleak; slot->location string was never freed ...
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6: [CRYPTO] padlock: Remove pointless padlock module [CRYPTO] api: Add ablkcipher_request_set_tfm [CRYPTO] cryptd: Add software async crypto daemon [CRYPTO] api: Do not remove users unless new algorithm matches [CRYPTO] cryptomgr: Fix parsing of nested templates [CRYPTO] api: Add async blkcipher type [CRYPTO] templates: Pass type/mask when creating instances [CRYPTO] tcrypt: Use async blkcipher interface [CRYPTO] api: Add async block cipher interface [CRYPTO] api: Proc functions should be marked as unused
-
Geert Uytterhoeven authored
ps3av: Replace GNU extension `__FUNCTION__' by C99 `__func__' Signed-off-by:
Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by:
-
Geert Uytterhoeven authored
ps3fb: Replace GNU extension `__FUNCTION__' by C99 `__func__' Signed-off-by:
-
Masashi Kimoto authored
ps3: Make `ps3videomode -v 0' (auto mode) work again Signed-off-by:
-
Geert Uytterhoeven authored
ps3av: - Move the definition of struct ps3av to ps3av.c, as it's locally used only. - Kill ps3av.sem, use the existing ps3av.mutex instead. - Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage. Its use is protected by a semaphore anyway. Signed-off-by: -
Geert Uytterhoeven authored
ps3fb: kill superfluous zero initializations Signed-off-by:
-
Geert Uytterhoeven authored
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread workqueue and a completion. Signed-off-by:
-
Geert Uytterhoeven authored
ps3fb: Use atomic_dec_if_positive() instead of bogus atomic_read()/atomic_dec() combinations Signed-off-by:
-
Geert Uytterhoeven authored
ps3fb: Replace the kernel_thread and the semaphore by a proper kthread, which is simply woken up when the screen must be updated Signed-off-by:
-
Geert Uytterhoeven authored
Convert kmap_atomic() in the non-highmem case from a macro to a static inline function, for better type-checking and the ability to pass void pointers instead of struct page pointers. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Geert Uytterhoeven authored
net/rxrpc/af-rxrpc.ko needs csum_partial_copy_from_user Signed-off-by:
-
Geert Uytterhoeven authored
The recent conversion from `memcpy' to `skb_copy_from_linear_data' removed a few casts, which were needed to silence compiler warnings. Re-add them. Signed-off-by:
-
Geert Uytterhoeven authored
Kill resource_size_t warnings by casting resource_size_t to unsigned long when formatting Zorro bus resources, as they are always 32-bit. Signed-off-by:
-
Finn Thain authored
Install the built-in macsonic interrupt handler on both IRQs when using via_alt_mapping. Otherwise the rare interrupt that still comes from the nubus slot will wedge the nubus. $ cat /proc/interrupts auto 2: 89176 via2 auto 3: 744367 sonic auto 4: 0 scc auto 6: 318363 via1 auto 7: 0 NMI mac 9: 119413 framebuffer vbl mac 10: 1971 ADB mac 14: 198517 timer mac 17: 89104 nubus mac 19: 72 Mac ESP SCSI mac 56: 629 sonic mac 62: 1142593 ide0 Version 1 of this patch had a bug where a nubus sonic card would register two interrupt handlers. Only a built-in sonic needs both. Versions 2 and 3 needed some cleanups, as Raylynn Knight and Christoph Hellwig pointed out (thanks). Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Finn Thain authored
Fix a potential problem in the timeout handling: don't free the DMA buffers before resetting the chip. Also a trivial cleanup. Bring macsonic and jazzsonic into sync. Signed-off-by:
-
Finn Thain authored
Fix a race condition in the transmit code, where the dma interrupt could update the free tx buffer count concurrently and wedge the tx queue. Fix the misuse of the rx frame status and rx frame length registers: no more "fifo overrun" errors caused by the OFLOW bit being tested in the frame length register (instead of the status register), and no more missed packets due to incorrect length taken from status register (instead of the frame length register). Fix a panic (skb_over_panic BUG) caused by allocating and then copying an incoming packet while the packet length register was changing. Cut-and-paste the reset code from the powermac mace driver (mace.c), so the NIC functions when MacOS does not initialise it (important for anyone wanting to use the Emile boot loader). Cut-and-paste the error counting and timeout recovery code from mace.c. Fix over allocation of rx buffer memory (it's page order, not page count). Converted to driver model. Converted to DMA API. Since I've run out of ways to make it fail, and since it performs well now, promote the driver from EXPERIMENTAL status. Tested on both quadra 840av and 660av. Signed-off-by:
-
Finn Thain authored
Fix the flakiness in the CUDA ADB driver on m68k macs (keypresses getting wedged down or ADB just going AWOL altogether). The only IRQ used by this driver is the VIA shift register IRQ. The PowerMac conditional code disables the other VIA IRQ sources, so don't mess with the other IRQ flags in the common code -- m68k macs need them. When polling, don't disable local interrupts when we only need to disable the CUDA interrupt. Unless polling, don't clear the shift register IRQ flag. On m68k macs this creates a race that often breaks CUDA ADB. Tested on Quadra 840av and LC630 (both m68k); also Beige G3 (powerpc). Signed-off-by:
-
Finn Thain authored
Fix a crash caused by requests placed in the queue with the completed flag already set. This lead to some ADB_SYNC requests returning early and their request structs being popped off the stack while still queued. Stack corruption ensued or an invalid request callback pointer was invoked or both. Eliminate macii_retransmit() and its buggy implementation of macii_write(). Have macii_queue_poll() fully initialise the request queues. Fix a bug in macii_queue_poll() where the last_req pointer was not being set. This caused some requests to leave the queue before being completed (and would also corrupt the stack under certain conditions). Fix a race in macii_start that could set the state machine to "reading" while current_req was null. No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused the replies to be stored in the request buffer where they were forgotten about. Don't autopoll by continuously sending new Talk commands. Get the controller to do that for us. This reduces the ADB interrupt rate on an idle bus to about 5 per second. Only autopoll the devices that were probed. Explicitly clear the interrupt flag when polling. Use disable_irq rather than local_irq_save when polling. Remove excess local_irq_save/restore pairs. Improve bus timeout and service request detection. Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len, first_byte etc). Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and ST_ODD). Add some commentry. Add a generous quantity of sanity checks (BUG_ONs). Let m68k macs use the adb_sync boot param too. Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc. Signed-off-by:
-
Finn Thain authored
There are no slow IRQs on Macs since Roman Zippel's IRQ reorganisation that went into 2.6.16 and removed mac_irq_list[] and the do_mac_irq_list() dispatcher. (They were implemented in do_mac_irq_list() by lowering the IPL.) Hence there's no more use for mutual exclusion in the Mac interrupt dispatchers. Remove it. Signed-off-by:
-
Finn Thain authored
Some Macs lack a slot interrupt enable register. So the existing code makes disabled and unregistered slot IRQ lines outputs set high. This seems to work on quadras, but does not work on genuine VIAs (perhaps the card still succeeds in pulling the line low, or perhaps because this increases the settle time on the port A input, meaning that the CA1 IRQ could fire before the slot line reads active). Because of this, the nubus_active flags were used to mask IRQs, which is actually worse than the problem it tries to solve. Any interrupt masked by nubus_active will remain asserted and prevent further transitions on CA1. And so the nubus gets wedged regardless of hardware (emulated VIA ASIC, real VIA chip or RBV). The best solution to this hardware limitation of genuine VIAs is to disable the umbrella SLOTS IRQ when disabling a slot on those machines. Unfortunately, this means all slot IRQs get disabled when any slot IRQ is disabled. But it is only a problem when there's more than 1 device using nubus interrupts. Another potential problem for genuine VIAs is an unregistered nubus IRQ. Eventually it will be possible to enable the CA1 interrupt by installing its handler only _after_ all nubus drivers have loaded but _before_ the kernel needs them, at which time this last problem can be fixed. For now it can be worked around: - disable MacOS extensions - don't boot MacOS (use the Emile bootloader instead) - get the bootloaders to disable ROM drivers (Penguin does this for video cards already, don't know about Emile) - physically remove unsupported cards Signed-off-by: -
Finn Thain authored
Make sure that there are no slot IRQs asserted before leaving the nubus handler. If there are and we don't then the nubus gets wedged because this prevents a CA1 transition, which means no more nubus IRQs. Make the interrupt dispatch loops terminate sooner. Explicitly initialise the VIA latches to make the code more easily understood. Also some cleanups. Signed-off-by:
-
Finn Thain authored
Reverse the last of a monumental brown-paper-bag commit that went into the 2.3 kernel. Signed-off-by:
-
Finn Thain authored
Fix the support for C/NET nubus ethernet cards etc. Sync up the DP8390 driver with the latest code in the mac68k repo. Signed-off-by:
-
Finn Thain authored
Sync the nubus defines with the latest code in the mac68k repo. Some of these are needed for DP8390 driver update in the next patch. Signed-off-by:
-
Finn Thain authored
Add some more machines that support A/UX interrupt priorities. There are probably others as well, but I've only tested these ones so far. Signed-off-by:
-
Finn Thain authored
The asm-m68k/adb.h header is unused. Some definitions are wrong and the rest are duplicated in linux/adb.h. Remove it. Signed-off-by:
-
Geert Uytterhoeven authored
Add missing code to the Amiga A2065 and Ariadne drivers to update net_device_stats.tx_bytes. Signed-off-by:
-
Finn Thain authored
Fixes a "static qualifier follows non-static qualifier" error from gcc 4. Signed-off-by:
Roman Zippel <zippel@linux-m68k.org> Signed-off-by:
-
Geert Uytterhoeven authored
Workqueue updates for the Atari SCSI driver Signed-off-by:
-
