- 09 Nov, 2011 40 commits
-
-
Franky Lin authored
Use SSB macros in order to clean up brcmfmac code Reviewed-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
Franky Lin <frankyl@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
Prepare for adding backplane interconnect type support Reviewed-by:
-
Franky Lin authored
Prepare for adding backplane interconnect type support Reviewed-by:
-
Franky Lin authored
Merged brcmf_sdbrcm_chip_attach into brcmf_sdio_chip_attach for better readability. Reviewed-by:
-
Franky Lin authored
Same register writes have been done in brcmf_sdbrcm_probe_init which is earlier in the same code path. Reviewed-by:
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
This will provide a better code flow that fits the logic Reviewed-by:
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
This patch is part of the abstracting chip backplane handle code series. Reviewed-by:
Roland Vossen <rvossen@broadcom.com> Signed-off-by:
-
Franky Lin authored
This patch is part of abstracting chip backplane handle code series. Reviewed-by:
-
Franky Lin authored
Currently backplane handle code is scatterd around dhd_sdio.c which is not good for maintenance and adding new backplane interconnect type support. This patch and the follow up patches are going to abstract all chip backplane control code specific for sdio bus into this new sdio_chip.c Reviewed-by:
-
Franky Lin authored
4329 with chiprev 0 can not be found on any product. The code can be removed. Reviewed-by:
-
Johannes Berg authored
For probe responses it can be useful to not wait for ACK to avoid retransmissions if the station that sent the probe is already on the next channel, so allow userspace to request not caring about the ACK with a new nl80211 flag. Since mac80211 needs to be updated for the new function prototype anyway implement it right away -- it's just a few lines of code. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
Implement the cfg80211 notification but only send one event per associated station to avoid having tons of events if the station thinks it should be allowed to use 4addr frames but it isn't. Signed-off-by:
-
Johannes Berg authored
The frames are used by AP/STA WDS mode, and hostapd needs to know when such a frame was received to set up the VLAN appropriately to allow using it. Signed-off-by:
-
Johannes Berg authored
If there's an interface in AP mode, OBSS beacons are needed by hostapd/wpa_s to implement logic to enable/disable protection etc. Report the frames and set the capability flag. Signed-off-by:
-
Johannes Berg authored
Add the ability to register to received beacon frames to allow implementing OLBC logic in userspace. The registration is per wiphy since there's no point in receiving the same frame multiple times. Signed-off-by:
-
Johannes Berg authored
Support probing clients with null data frames in AP mode. Signed-off-by:
-
Johannes Berg authored
When the AP SME in hostapd is used it wants to probe the clients when they have been idle for some time. Add explicit API to support this. Signed-off-by:
-
Johannes Berg authored
Add the ability to advertise that the device contains the AP SME and what features it can support. There are currently no features in the bitmap -- probe response offload will be advertised by a few patches Arik is working on now (who took over from Guy Eilam) and a device with AP SME will typically implement and require response offload. Signed-off-by:
-
Johannes Berg authored
Add support for the spurious class3 frame event to mac80211 to enable AP w/o monitor mode. Signed-off-by:
-
Johannes Berg authored
To implement AP mode without monitor interfaces we need to be able to send a deauth to stations that send frames without being associated. Enable this by adding a new nl80211 event for such frames that an application can subscribe to. Signed-off-by:
-
Johannes Berg authored
This will allow us to support dynamic WEP with 802.1X properly in mac80211 by not encrypting outgoing and accepting unencrypted incoming frames. Signed-off-by:
-
Johannes Berg authored
Drivers that need to drop a frame before it can be transmitted will usually simply free that frame. This is currently fine, but in the future it'll be needed to tell mac80211 about this case, so add a new routine that frees a TX skb. Signed-off-by:
-
Javier Cardona authored
We only need to set the skb queue twice: 1. by the netdev, on local TX. 2. when forwarding a mesh frame. We only need to set the qos header twice: 1. by mac80211, on local TX. 2. when putting a frame on the mpath->frame_queue We also don't need the RA in order to set the proper queue mapping since all mesh STAs are QoS, indicate this and do it once when the frame is received. Also fixes an issue where the QoS header and queue mapping was not set for unicast forwarded frames. Signed-off-by:
Javier Cardona <javier@cozybit.com> Signed-off-by:
Thomas Pedersen <thomas@cozybit.com> Signed-off-by:
-
Thomas Pedersen authored
There was an an implicit assumption that any QoS data frame received from a STA/TID with an active BA session was sent to this vif as part of a BA. This is not true if IFF_PROMISC is enabled and the frame was destined for a different peer, for example. Don't treat these frames as part of a BA from the sending STA. Signed-off-by:
-
Thomas Pedersen authored
Previously QoS multicast frames had the Normal Acknowledgment QoS control bits set. This would cause broadcast frames to be discarded by peers with which we have a BA session, since their sequence number would fall outside the allowed range. Set No Ack QoS control bits on multicast QoS frames and filter these in de-aggregation code. Signed-off-by:
-
Javier Cardona authored
Don't accept redundant PREQs for a given destination. This fixes a problem under high load: kernel: [20386.250913] mesh_queue_preq: 235 callbacks suppressed kernel: [20386.253335] Mesh HWMP (mesh0): PREQ node queue full kernel: [20386.253352] Mesh HWMP (mesh0): PREQ node queue full (...) The 802.11s protocol has a provision to limit the rate of path requests (PREQs) are transmitted (dot11MeshHWMPpreqMinInterval) but there was no limit on the rate at which PREQs were being queued up. There is a valid reason for queuing PREQs: this way we can even out PREQ bursts. But queueing multiple PREQs for the same destination is useless. Reported-by:
Pedro Larbig <pedro.larbig@carhs.de> Signed-off-by:
-
Ben Greear authored
Add interface address so it can be mapped to a local interface. Add max-ampdu and mpdu-density. Print out the tid->baw_size Signed-off-by:
Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Johannes Berg authored
The driver is never informed about monitor or AP_VLAN interfaces, so whenever we pass those to it later this is a bug. Verify we don't as there are some cases where this could happen. Signed-off-by:
-
Johannes Berg authored
The 802.1X EAPOL handshake hostapd does requires knowing whether the frame was ack'ed by the peer. Currently, we fudge this pretty badly by not even transmitting the frame as a normal data frame but injecting it with radiotap and getting the status out of radiotap monitor as well. This is rather complex, confuses users (mon.wlan0 presence) and doesn't work with all hardware. To get rid of that hack, introduce a real wifi TX status option for data frame transmissions. This works similar to the existing TX timestamping in that it reflects the SKB back to the socket's error queue with a SCM_WIFI_STATUS cmsg that has an int indicating ACK status (0/1). Since it is possible that at some point we will want to have TX timestamping and wifi status in a single errqueue SKB (there's little point in not doing that), redefine SO_EE_ORIGIN_TIMESTAMPING to SO_EE_ORIGIN_TXSTATUS which can collect more than just the timestamp; keep the old constant as an alias of course. Currently the internal APIs don't make that possible, but it wouldn't be hard to split them up in a way that makes it possible. Thanks to Neil Horman for helping me figure out the functions that add the control messages. Signed-off-by:
-
Stanislaw Gruszka authored
Since local->tmp_channel is always NULL in one branch, some code paths will newer be taken in that branch, so remove them. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Johannes Berg authored
Janusz reported that the EOSP bit in mac80211 was getting cleared all the time. I had not found this since I tested uAPSD with a device that always set the bit itself. Preserve the bit when building the QoS header. Reported-by:
Janusz Dziedzic <janusz.dziedzic@gmail.com> Tested-by:
-
Jouni Malinen authored
WPI-SMS4 uses 16-octet PN field, so we need to allow longer key sequence values to be configured. Signed-off-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
-
Jouni Malinen authored
This value is used for WPI-SMS4 in ISO/IEC JTC 1 N 9880. Signed-off-by:
-
