While releasing memory during error path exit, invalid memory pointer
was used for dapm_routes. Use a valid one.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

While mapping control id to define DAPM routes, invalid control index
may cause kernel oops. Add extra check to validate index while mapping
names to control_id.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In the beginning, module side can control the vibrator timeout value,
it can disable vibrator until timeout. But after Runtime PM control added
in, AP side didn't know when module can be suspended, the vibrator
task will be interrupted by suspending event.

Because of this problem, the module can not be in charge of counting down
the timeout value, it is now up to the AP to manage this. So add workqueue
to handle the vibrator timeout.
Signed-off-by: Ann Chen <chen_ann@projectara.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

In case a bulk-in transfer-buffer allocation failed during probe, we'd
currently leak the corresponding URB.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove support for module implementing legacy version of camera bandwidth
requirements specifications, now that all available camera modules have
been updated to use the new version
Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The firmware file name's maximum length is set to 56 right now, but it
isn't very much readable how we got to that value (unless someone reads
that line).

Update the comment to show calculations.
Reported-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Replace 'should' with 'must' to clear the expectation a bit more.
Reported-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Alex Elder pointed out that the macros also count the trailing NULL
('\0') character and so it should be using SIZE instead of LEN.

This patch makes that change.
Reported-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove the unnecessary parenthesis.
Reported-by: Alex Elder <alex.elder@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

s/shall be used the user/shall be used by the user/
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

We already have another direct pointer for this, use that instead.

Testing Done: Compiled.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make the control-protocol disconnecting operation a "core" operation.

This is needed to be able to use the operation in the new connection
tear-down sequence of control connections, which moves disconnecting
after the flush barrier.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add a host-device cport_shutdown callback which will be called as part
of the new connection tear-down sequence for offloaded connection in
order to do a cport_shutdown operation on behalf of the AP.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add a host-device cport_clear callback, which will be called as part
of the new connection tear-down sequence to reset the CPort state.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add a host-device cport_quiesce callback, which will be called as part
of the new connection tear-down sequence to disable flow control after
first making sure that enough peer buffer space is available for the
next messages about to be sent.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add a host-device cport_connected callback, which will be called after a
connection has been created and that can be used by the host-device
driver to make sure its internal state is updated to match the CPort
attributes set by the SVC.

This callback will eventually replace the cport_features_enable
callback.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

I got them wrong, Johan was right, my fault.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

A backport (commit 79c4de08c0e5a26b04a4ac9e6543dad6379f0b40) was
applied in kernel which adding attribute-group support in led-class.
Remove the LED_HAVE_GROUPS flag check entirely that allow led
drivers to create custom attributes like color/fade_in/fade_out.

Testing Done: Compiled and verified on EVT2 and gpbridge-test module
              with device class daughter board.
Signed-off-by: Kris Huang <huang_kris@projectara.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add intf_oops operation to SVC Protocol. This
operation will notify the AP about a fatal error
in a module. The request has two arguments:
    -u8 intf - the interface in question
    -u8 reason - reason of the error
The response has no payload.
Upon receiving the Request, the driver disables
the Interface.
Signed-off-by: Georgi Dobrev <gdobrev@mm-sol.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ashwin Chaugule <ashwinch@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove last occurrence of "ara" term in camera driver.
Replace reference to "ara subdevice" with "gmp subdevice"
Signed-off-by: Jacopo Mondi <jacopo.mondi@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Move the ARPC definitions to their own header.

ARPC is not part of greybus, but is rather an implementation-specific
means of communicating with a certain class of host-device hardware.

Note that the same is true for the APBA USB vendor requests, but we keep
them in the greybus header for the time being.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to use the common GB_APB prefix for all APBA USB vendor
requests.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Fix copy-paste error in an APBA USB vendor-request comment.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Adjust maximum segment size of the sg list to meet the maximum request
size, this will allow to have less segments which increase the
performance of data movement during transfer operations.

Test Done: using mmc_test with best-case read/write performance and see
that only one segment is used and that the results are better (288KiB vs
300KiB in read operation).
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Order of the field of the sdio get caps operation response were wrong,
that influence later the frequencies used by core, during normal
operation.

Tested: verified that the values inserted by the fw are the correct ones
for the field.
Suggested-by: Jackson Chang <jacksonc@bsquare.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

When enabling an interface, control device should be registered after
having successfully added the timesync. Similarly for the interface
disable path, control device should be removed first before removing
timesync.

Testing Done:
 - Enable and disable the interface
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Suggested-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: David Lin <dtwlin@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

For GB module with jack slot supported, headset/headphone can still
be inserted at the time of module removal. In this case, above layer is
unaware about jack removal event which happened due to module removal.
This may lead to inconsistent state in above HAL layer.  Fix this by
reporting jack removal event explicitly.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Modify Lights greybus driver to support runtime PM framework.
The suspend and resume function have been tested with gpbridge-test
image by sysfs. Lights functions work well on suspend/resume.

Testing Done: Compiled and verified on EVT2 and gpbridge-test module
              with device class daughter board.
Signed-off-by: Kris Huang <huang_kris@projectara.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Modify SDIO greybus driver to support runtime PM framework.
To enable SDIO runtime PM, it needs to remove MMC_CAP_NEEDS_POLL
and add MMC_CAP2_CORE_RUNTIME_PM in set_host_caps().
The suspend function and resume function have been tested
with micron-sdio image by sysfs. SDIO functions work well
on suspend/resume.

Testing Done: Compiled and verified on EVT2.0 + Micron ARA
              SD module with USB connector
Signed-off-by: Jackson Chang <chang_jackson@projectara.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

For SPK module, each data connection corresponds to codec DAI. Now
stream state is maintained for each DAI. So, need to maintain stream
state for each DAI/data connection for individual module as well.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Runtime streams are required while configuring GB module plugged-in
during active stream. Currently, it is maintained for single stream.
However, this should be maintained for a stream corresponding to each
DAI. Fix this!
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Ensure pm runtime get_sync/put protection in codec_dai ops callback
functions before accessing apbridge.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Audio codec driver internally maintains a struct containing info about
module's data connection. Remove unused field from this struct.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently we are using dai->name to identify data connection from list
for a module. Now since we are enabling data path based on widget,
dai->name might be invalid by the time driver receives disable request
for a widget. So, use id fetched from AIF widget->sname to identify data
connection for a module.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Added id field to data connection struct. This is used to identify which
data connection to use while enabling interface between module & APB.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently, SPK Amp switch is used to identify when to enable data path
between module and APB. With headset, other switch controls added, it is
not possible to use this switch to control data path. Instead path
should be established based on AIF widget.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Earlier, module path was enabled based on module's control switch e.g.
'SPK Amp switch'.  Thus widget's name was sufficient to parse and
identify the direction. Now individual modules' path will be enabled
based on AIF widget status. So, it is required to get complete widget
details, say w->type is used to identify direction (playback/capture)
and w->sname is used to identify module's DATA connection used for
communication via greybus.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently, the stream name for the DAI driver is generically set to "GB
Audio Playback" and "GB Audio Capture". This is OK since we use a single
interface on APB1 but that could change in the future.  Update the DAI
driver table entries to properly reflect the interface used.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Now, module is enabled/disabled based on widget event only and not
during startup/shutdown callbacks. Thus, we needn't compare codec_state
in enable/disable module helper APIs. Also, these can be further
simplified based on stream direction.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

As per current implementation, audio data is played from each individual
SPK module connected to endo frame. This is not a valid requirement in
case of capture/headset path. So, provide a mechanism to enable
individual module path based on it's control switch state.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>