- 19 Apr, 2023 5 commits
-
-
Pradeep Kumar Chitrapu authored
ieee80211_tx_status() treats packets in 802.11 frame format and tries to extract sta address from packet header. When tx encap offload is enabled, this becomes invalid operation. Hence, switch to using ieee80211_tx_status_ext() after filling in station address for handling both 802.11 and 802.3 frames. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230403195738.25367-2-quic_pradeepc@quicinc.com
-
Harshitha Prem authored
During reo command failure, the peer mac detail for which the reo command was not successful is unknown. Hence, to improve the debuggability, add the peer mac information in the failure cases which would be useful during multi client cases. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Sathishkumar Muruganandam <quic_murugana@quicinc.com> Signed-off-by:
Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by:
-
Harshitha Prem authored
Prevent REO cmd failures causing double free by increasing REO cmd ring size and moving REO status ring mask to IRQ group 3 from group 0 to separate from tx completion ring on IRQ group 0 which may delay reo status processing. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Harshitha Prem authored
Peer rx_tid is locally copied thrice during peer_rx_tid_cleanup to send REO_CMD_UPDATE_RX_QUEUE followed by REO_CMD_FLUSH_CACHE to flush all aged REO descriptors from HW cache. When sending REO_CMD_FLUSH_CACHE fails, we do dma unmap of already mapped rx_tid->vaddr and free it. This is not checked during reo_cmd_list_cleanup() and dp_reo_cmd_free() before trying to free and unmap again. Fix this by setting rx_tid->vaddr NULL in rx tid delete and also wherever freeing it to check in reo_cmd_list_cleanup() and reo_cmd_free() before trying to free again. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Konrad Dybcio authored
Convert the ath10k bindings to YAML. Dropped properties that are absent at the current state of mainline: - qcom,msi_addr - qcom,msi_base Somewhat based on the ath11k bindings. Signed-off-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
- 17 Apr, 2023 7 commits
-
-
Jonas Jelonek authored
Fix incorrect usage of plain rate_idx as index into the max (power) per rate lookup table. For transmit power control (TPC), the ath9k driver maintains internal tables (in struct ath_hw) to store the max allowed power level per rate. They are used to limit a given TX-power according to regulatory and user limits in the TX-path per packet. The tables are filled in a predefined order, starting with values for CCK + OFDM rates and followed by the values for MCS rates. Thus, the maximum power levels for MCS do not start at index 0 in the table but are shifted by a fixed value. The TX-power limiting in ath_get_rate_txpower currently does not apply this shift, thus retrieves the incorrect maximum power level for a given rate. In particular for MCS rates, the maximum power levels for CCK/OFDM rates were used, e.g. maximum power for OFDM 0 was used for MCS 0. If STBC is used, the power is mostly limited to 0 because the STBC table is zeroed for legacy CCK/OFDM rates. Encountered this during testing of our work-in-progress TPC per packet for ath9k. This only has an effect when TPC is enabled in ath9k (tpc_enabled in struct ath_hw) which defaults to false. In this case it has a significant impact on the used TX-power, throughput + RSSI. Otherwise the affected code is just skipped and TX-power is limited with the hardware registers only. This patch fixes this table lookup. Tested on OpenWrt (kernel 5.15.98, but backported ath9k driver) with small desk setup using ath9k chips AR9280 and AR9580. Cap of TX-power is working properly for all rates now, throughput and RSSI as expected, equal to as if TPC was disabled. Compile-tested with latest 6.3 kernel + allyesconfig. Signed-off-by:
Jonas Jelonek <jelonek.jonas@gmail.com> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
Harshitha Prem authored
"__fls" would have an undefined behavior if the argument is passed as "0". Hence, added changes to handle the same. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Nagarajan Maran <quic_nmaran@quicinc.com> Signed-off-by:
-
Harshitha Prem authored
When max virtual ap interfaces are configured in all the bands with ACS and hostapd restart is done every 60s, a crash is observed at random times. In this certain scenario, a fragmented packet is received for self peer, for which rx_tid and rx_frags are not initialized in datapath. While handling this fragment, crash is observed as the rx_frag list is uninitialised and when we walk in ath11k_dp_rx_h_sort_frags, skb null leads to exception. To address this, before processing received fragments we check dp_setup_done flag is set to ensure that peer has completed its dp peer setup for fragment queue, else ignore processing the fragments. Call trace: ath11k_dp_process_rx_err+0x550/0x1084 [ath11k] ath11k_dp_service_srng+0x70/0x370 [ath11k] 0xffffffc009693a04 __napi_poll+0x30/0xa4 net_rx_action+0x118/0x270 __do_softirq+0x10c/0x244 irq_exit+0x64/0xb4 __handle_domain_irq+0x88/0xac gic_handle_irq+0x74/0xbc el1_irq+0xf0/0x1c0 arch_cpu_idle+0x10/0x18 do_idle+0x104/0x248 cpu_startup_entry+0x20/0x64 rest_init+0xd0/0xdc arch_call_rest_init+0xc/0x14 start_kernel+0x480/0x4b8 Code: f9400281 f94066a2 91405021 b94a0023 (f9406401) Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Kalle Valo authored
Christoph reported that ath11k failed to initialise when michael_mic.ko module was not installed. To make it easier to notice that case print a warning when crypto_alloc_shash() fails. Compile tested only. Reported-by:
Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/all/20221130133016.GC3055@lst.de/Signed-off-by:
-
Takashi Iwai authored
As there are a few more models supported by the driver, let's add the missing MODULE_FIRMWARE() entries for them. The lack of them resulted in the missing device enablement on some systems, such as the installation image of openSUSE. While we are at it, use the wildcard instead of listing each firmware files individually for each. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Youghandhar Chintala authored
Currently, SAR is enabled only on WCN6855, enable this for WCN6750 too. This functionality gets triggered, when the user space application calls NL80211_CMD_SET_SAR_SPECS. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
Youghandhar Chintala <quic_youghand@quicinc.com> Signed-off-by:
-
Tamizh Chelvam Raja authored
Host might receive spectral events during interface down sequence and this might create below errors. failed to handle dma buf release event -22 failed to handle dma buf release event -22 Fix this by disabling spectral config during remove interface. Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Tamizh Chelvam Raja <quic_tamizhr@quicinc.com> Signed-off-by:
-
- 12 Apr, 2023 9 commits
-
-
Cai Huoqing authored
Remove pci_clear_master to simplify the code, the bus-mastering is also cleared in do_pci_disable_device, like this: ./drivers/pci/pci.c:2197 static void do_pci_disable_device(struct pci_dev *dev) { u16 pci_command; pci_read_config_word(dev, PCI_COMMAND, &pci_command); if (pci_command & PCI_COMMAND_MASTER) { pci_command &= ~PCI_COMMAND_MASTER; pci_write_config_word(dev, PCI_COMMAND, pci_command); } pcibios_disable_device(dev); }. And dev->is_busmaster is set to 0 in pci_disable_device. Signed-off-by:Cai Huoqing <cai.huoqing@linux.dev> Signed-off-by:
-
Cai Huoqing authored
Remove pci_clear_master to simplify the code, the bus-mastering is also cleared in do_pci_disable_device, like this: ./drivers/pci/pci.c:2197 static void do_pci_disable_device(struct pci_dev *dev) { u16 pci_command; pci_read_config_word(dev, PCI_COMMAND, &pci_command); if (pci_command & PCI_COMMAND_MASTER) { pci_command &= ~PCI_COMMAND_MASTER; pci_write_config_word(dev, PCI_COMMAND, pci_command); } pcibios_disable_device(dev); }. And dev->is_busmaster is set to 0 in pci_disable_device. Signed-off-by: -
Cai Huoqing authored
Remove pci_clear_master to simplify the code, the bus-mastering is also cleared in do_pci_disable_device, like this: ./drivers/pci/pci.c:2197 static void do_pci_disable_device(struct pci_dev *dev) { u16 pci_command; pci_read_config_word(dev, PCI_COMMAND, &pci_command); if (pci_command & PCI_COMMAND_MASTER) { pci_command &= ~PCI_COMMAND_MASTER; pci_write_config_word(dev, PCI_COMMAND, pci_command); } pcibios_disable_device(dev); }. And dev->is_busmaster is set to 0 in pci_disable_device. Signed-off-by: -
Manikanta Pubbisetty authored
Firmwares advertising the support of triggering 11d algorithm on the scan results of a regular scan expects driver to send WMI_11D_SCAN_START_CMDID before sending WMI_START_SCAN_CMDID. Triggering 11d algorithm on the scan results of a normal scan helps in completely avoiding a separate 11d scan for determining regdomain. This indirectly helps in speeding up connections on station interfaces on the chipsets supporting 11D scan. To enable this feature, send WMI_11D_SCAN_START_CMDID just before sending WMI_START_SCAN_CMDID if the firmware advertises WMI_TLV_SERVICE_SUPPORT_11D_FOR_HOST_SCAN service flag. WCN6750 & WCN6855 supports this feature. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
-
P Praneesh authored
While initializing spectral, the magic value is getting written to the invalid memory address leading to random boot-up crash. This occurs due to the incorrect index increment in ath11k_dbring_fill_magic_value function. Fix it by replacing the existing logic with memset32 to ensure there is no invalid memory access. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Fixes: d3d358ef ("ath11k: add spectral/CFR buffer validation support") Signed-off-by:
P Praneesh <quic_ppranees@quicinc.com> Signed-off-by:
-
Bhagavathi Perumal S authored
The WMI management rx event has multiple arrays of TLVs, however the common WMI TLV parser won't handle multiple TLV tags of same type. So the multiple array tags of WMI management rx TLV is parsed incorrectly and the length calculated becomes wrong when the target sends multiple array tags. Add separate TLV parser to handle multiple arrays for WMI management rx TLV. This fixes invalid length issue when the target sends multiple array tags. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Bhagavathi Perumal S <quic_bperumal@quicinc.com> Co-developed-by:
-
P Praneesh authored
In QCN9074, station dump signal values display default value which is -95 dbm, since there is firmware header change for HAL_RX_MPDU_START between QCN9074 and IPQ8074 which cause wrong peer_id fetch from msdu. Fix this by updating hal_rx_mpdu_info with corresponding QCN9074 tlv format. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Ganesh Babu Jothiram authored
Fine Time Measurement(FTM) is offloaded feature to firmware. Hence, the configuration of FTM responder role is done using firmware capability flag instead of hw param. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Ganesh Babu Jothiram <quic_gjothira@quicinc.com> Signed-off-by:
-
Manikanta Pubbisetty authored
Currently, time taken to scan all supported channels on WCN6750 is ~8 seconds and connection time is almost 10 seconds. WCN6750 supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of channels for scan come around ~100 channels (default case). Since the chip doesn't have support for DBS (Dual Band Simultaneous), scans cannot be parallelized resulting in longer scan times. Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore, optimizing the scan for 6 GHz channels will bring down the overall scan time. WCN6750 firmware has support to scan a 6 GHz channel based on co-located AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan results. When a scan request with all supported channel list is enqueued to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND scan channel flag, firmware will scan only those 6 GHz channels for which RNR IEs are found in the legacy scan results. In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag for non-PSC channels. Since there is high probability to find 6 GHz APs on PSC channels, these channels are always scanned. Only non-PSC channels are selectively scanned based on cached RNR information from the legacy scan results. If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags, then scan will happen on all supported channels (default behavior). With these optimizations, scan time is improved by 1.5-1.8 seconds on WCN6750. Similar savings have been observed on WCN6855. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16 Signed-off-by:
-
- 24 Mar, 2023 8 commits
-
-
Gustavo A. R. Silva authored
Zero-length arrays as fake flexible arrays are deprecated and we are moving towards adopting C99 flexible-array members instead. Address the following warnings found with GCC-13 and -fstrict-flex-arrays=3 enabled: drivers/net/wireless/ath/carl9170/tx.c:702:61: warning: array subscript i is outside array bounds of ‘const struct _carl9170_tx_status[0]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/tx.c:701:65: warning: array subscript i is outside array bounds of ‘const struct _carl9170_tx_status[0]’ [-Warray-bounds=] This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/21 Link: https://github.com/KSPP/linux/issues/267 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by:
Christian Lamparter <chunkeey@gmail.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Gustavo A. R. Silva authored
GCC (and Clang)[1] does not like having a partially allocated object, since it cannot reason about it for bounds checking. Instead, fully allocate struct carl9170_cmd. Fix the following warnings Seen under GCC 13: drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[4]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[4]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:161:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:162:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:163:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:164:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[20]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:125:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:126:30: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=] drivers/net/wireless/ath/carl9170/cmd.c:220:12: warning: array subscript ‘struct carl9170_cmd[0]’ is partly outside array bounds of ‘unsigned char[8]’ [-Warray-bounds=] Link: https://github.com/KSPP/linux/issues/268 Link: godbolt.org/z/KP97sxh3T [1] Signed-off-by:
-
Tom Rix authored
clang with W=1 reports: drivers/net/wireless/ath/ath10k/ce.c:88:1: error: unused function 'ath10k_get_ring_byte' [-Werror,-Wunused-function] ath10k_get_ring_byte(unsigned int offset, ^ This function is not used so remove it. Signed-off-by:
Tom Rix <trix@redhat.com> Signed-off-by:
-
Johan Hovold authored
Add devicetree bindings for Qualcomm ath11k PCIe devices such as WCN6855 for which the calibration data variant may need to be described. Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Reviewed-by:
-
Harshitha Prem authored
When underlying hardware supports more than one band, then wiphy is aware of all the frequency bands present. Example, say wiphy0 is aware of 2 GHz, 5 GHz and 6 GHz band information. Hence, when an virtual AP interface is brought up in auto channel selection on each band. Survey is initiated from the userspace application for all the virtual AP interfaces simultaneously. For survey dump collection, freq_to_idx() api is used to map the index of particular frequency to populate its survey. When the dump was collected, the index fetched was incorrect. Example, in case of multi-hardware, the index of channel 36 was reported as 14, because wiphy0 had index 0-13 for 2 GHz channels, instead of 0 for that ar which resulted in invalid survey sent to userspace application. The incorrect index was because of the mapping did not consider whether the freq band is present in its radio structure (ar) or not. To handle this, the freq_to_idx() api should map index for the particular band in the ar structure. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Harshitha Prem authored
When a data traffic with size greater than 1500 is initiated, say size 65500, it is sent as a set of AMSDUs (3 MSDUs) in a MPDU. These AMSDUs are incorrectly classified as multicast and peer id gets changed, except for first msdu, because of mcast_bcast bit derived from rx_desc for every msdu received. The mcast_bcast bit in rx_desc is only valid for first msdu. Hence, add changes to derive mcast_bcast only if it is a first msdu. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
Aaradhana Sahu authored
Currently, if we set raw mode as encap type, packets are sent in native wifi mode which is default mode. This is caused by no check being present for raw mode in ath12k_dp_tx_get_encap_type function, so it's always going in native wifi mode. Fix, this issue by adding check condition for raw mode. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Aaradhana Sahu <quic_aarasahu@quicinc.com> Signed-off-by:
-
P Praneesh authored
Firmware expects physical address in the reo entrance ring when MLO is enabled and peer meta data in the queue_addr_lo for the non MLO cases. Current implementation fills the physical address for the non MLO cases and firmware decodes it differently which leads to SOC CSR region access which is not related to firmware/MAC operation. Fix this by sending only peer_meta data and destination indication bit during non MLO case. This prevents firmware from invalid decoding. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manish Dharanenthiran <quic_mdharane@quicinc.com> Signed-off-by:
-
- 22 Mar, 2023 5 commits
-
-
Baochen Qiang authored
To reduce power consumption, change idle_ps to true to enable Idle Mode Power Save (IMPS) for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by:
Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
-
Baochen Qiang authored
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel included in scan channel list. Without it, firmware will not send a probe request frame which is needed in connection to an AP configured with hidden SSID/network_id. So fix this to allow probe request frames to be sent in cases where a beacon frame has been seen on the channel first. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by:
-
Aditya Kumar Singh authored
Currently, during change in bandwidth for peer sta, host sends the new value of channel width via WMI_PEER_CHWIDTH set peer param command alone. This can lead to firmware assert in some scenario since before the command, firmware was having value of channel width and its corresponding phymode. After the command, host tries to set the new value of channel width alone which can become incompatible when compared with its phymode. For example: Bandwidth Upgrade ~~~~~~~~~~~~~~~~~~ After association, sta is in 40 MHz bandwidth in 11ax-HE40 phymode. After bandwidth upgrades, sta moves to 80 MHz but as per phymode, max bandwidth is still 40 MHz. Hence, firmware assert is seen. So in this case first phymode should be moved to 11ax-HE80 followed by bandwidth change. Bandwidth Downgrade ~~~~~~~~~~~~~~~~~~ Similarly, reverse of above is also possible when sta is in 40 MHz bandwidth in 11ax-HE40 phymode. Bandwidth should be changed to 20 MHz and if host sends phymode first then, phymode will become 11ax-HE20 and will be incompatible with bandwidth value and hence firmware assert will be seen. Hence, in this case first channel width should be set followed by phymode. Fix this issue by sending WMI set peer param command for phymode as well as bandwidth based on the type of bandwidth change i.e upgrade or downgrade. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Aditya Kumar Singh <quic_adisi@quicinc.com> Signed-off-by:
-
Rajat Soni authored
Currently the buffer pointed by event is not freed in case ATH12K_FLAG_UNREGISTERING bit is set, this causes memory leak. Add a goto skip instead of return, to ensure event and all the list entries are freed properly. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Rajat Soni <quic_rajson@quicinc.com> Signed-off-by:
-
Harshitha Prem authored
Perform dma_sync_single_for_cpu() on monitor ring rx buffer before reading BUFFER_DONE tag and do dma_unmap_single() only after device had set BUFFER_DONE tag to the buffer. Also when BUFFER_DONE tag is not set, allow the buffer to get read next time without freeing skb. This helps to fix AP+Monitor VAP with flood traffic scenario to see monitor ring rx buffer overrun missing BUFFER_DONE tag to be set. Also remove redundant rx dma buf free performed on DP rx_mon_status_refill_ring. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by:
-
- 15 Mar, 2023 5 commits
-
-
Aditya Kumar Singh authored
Currently, in ath11k_ahb_fw_resources_init(), iommu domain mapping is done only for the chipsets having fixed firmware memory. Also, for such chipsets, mapping is done only if it does not have TrustZone support. During deinitialization, only if TrustZone support is not there, iommu is unmapped back. However, for non fixed firmware memory chipsets, TrustZone support is not there and this makes the condition check to true and it tries to unmap the memory which was not mapped during initialization. This leads to the following trace - [ 83.198790] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008 [ 83.259537] Modules linked in: ath11k_ahb ath11k qmi_helpers .. snip .. [ 83.280286] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 83.287228] pc : __iommu_unmap+0x30/0x140 [ 83.293907] lr : iommu_unmap+0x5c/0xa4 [ 83.298072] sp : ffff80000b3abad0 .. snip .. [ 83.369175] Call trace: [ 83.376282] __iommu_unmap+0x30/0x140 [ 83.378541] iommu_unmap+0x5c/0xa4 [ 83.382360] ath11k_ahb_fw_resource_deinit.part.12+0x2c/0xac [ath11k_ahb] [ 83.385666] ath11k_ahb_free_resources+0x140/0x17c [ath11k_ahb] [ 83.392521] ath11k_ahb_shutdown+0x34/0x40 [ath11k_ahb] [ 83.398248] platform_shutdown+0x20/0x2c [ 83.403455] device_shutdown+0x16c/0x1c4 [ 83.407621] kernel_restart_prepare+0x34/0x3c [ 83.411529] kernel_restart+0x14/0x74 [ 83.415781] __do_sys_reboot+0x1c4/0x22c [ 83.419427] __arm64_sys_reboot+0x1c/0x24 [ 83.423420] invoke_syscall+0x44/0xfc [ 83.427326] el0_svc_common.constprop.3+0xac/0xe8 [ 83.430974] do_el0_svc+0xa0/0xa8 [ 83.435659] el0_svc+0x1c/0x44 [ 83.438957] el0t_64_sync_handler+0x60/0x144 [ 83.441910] el0t_64_sync+0x15c/0x160 [ 83.446343] Code: aa0103f4 f9400001 f90027a1 d2800001 (f94006a0) [ 83.449903] ---[ end trace 0000000000000000 ]--- This can be reproduced by probing an AHB chipset which is not having a fixed memory region. During reboot (or rmmod) trace can be seen. Fix this issue by adding a condition check on firmware fixed memory hw_param as done in the counter initialization function. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Fixes: f9eec494 ("ath11k: Add support for targets without trustzone") Signed-off-by:
-
Gustavo A. R. Silva authored
Zero-length arrays as fake flexible arrays are deprecated and we are moving towards adopting C99 flexible-array members instead. Address 25 of the following warnings found with GCC-13 and -fstrict-flex-arrays=3 enabled: drivers/net/wireless/ath/ath11k/debugfs_htt_stats.c:30:51: warning: array subscript <unknown> is outside array bounds of ‘const u32[0]’ {aka ‘const unsigned int[]’} [-Warray-bounds=] This helps with the ongoing efforts to tighten the FORTIFY_SOURCE routines on memcpy() and help us make progress towards globally enabling -fstrict-flex-arrays=3 [1]. Link: https://github.com/KSPP/linux/issues/21 Link: https://github.com/KSPP/linux/issues/266 Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1] Signed-off-by: -
Harshit Mogalapalli authored
Smatch Warns: drivers/net/wireless/ath/ath12k/pci.c:1198 ath12k_pci_probe() warn: missing unwind goto? Store the error value in ret and use correct label with a goto. Only Compile tested, found with Smatch. Fixes: d8899132 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Reported-by:
Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/all/Y+426q6cfkEdb5Bv@kili/Suggested-by:
Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Reviewed-by:
-
Vladimir Lypak authored
Pronto v3 has a different DXE address than prior Pronto versions. This patch changes the macro to return the correct register address based on the pronto version. Signed-off-by:
Vladimir Lypak <vladimir.lypak@gmail.com> Signed-off-by:
Sireesh Kodali <sireeshkodali1@gmail.com> Signed-off-by:
-
Bastian Germann authored
The USB device 1668:1200 is Qwest/Actiontec 802AIN which is also correctly claimed to be supported by carl9170. Supposedly, the successor 802AIN2 has an ath9k compatible chip whose USB ID (unknown) could be inserted instead. Drop the ID from the wrong driver. I happened to find this by chance while packaging the ath9k and carl9170 firmware for Debian. Signed-off-by:
Bastian Germann <bage@debian.org> Acked-by:
-
- 13 Mar, 2023 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v6.4. Major changes: ath10k * enable threaded napi on WCN3990 ath11k * push MU-MIMO params from hostapd to hardware * tx ack signal support for management packets
-
