dev_get_drvdata() on iio_dev->dev no longer returns the iio_dev.
Use dev_to_iio_dev() to get iio_dev struct.

Fixes: 8b7651f2 ("iio: iio_device_alloc(): Remove unnecessary self drvdata")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1645702191-9400-1-git-send-email-haibo.chen@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Document the LTC2688 devicetree properties.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220225130129.69-4-nuno.sa@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Define the sysfs interface for toggle or dither capable channels. Dither
capable channels will have the extended interface:

 * out_voltageY_dither_en
 * out_voltageY_dither_raw
 * out_voltageY_dither_offset
 * out_voltageY_dither_raw_available
 * out_voltageY_dither_frequency
 * out_voltageY_dither_frequency_available
 * out_voltageY_dither_phase
 * out_voltageY_dither_phase_available

Toggle enabled channels will have:

 * out_voltageY_toggle_en
 * out_voltageY_raw0
 * out_voltageY_raw1
 * out_voltageY_symbol

The common interface present in all channels is:

 * out_voltageY_raw (not present in toggle enabled channels)
 * out_voltageY_raw_available
 * out_voltageY_powerdown
 * out_voltageY_scale
 * out_voltageY_offset
 * out_voltageY_calibbias
 * out_voltageY_calibscale
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220225130129.69-3-nuno.sa@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The LTC2688 is a 16 channel, 16 bit, +-15V DAC with an integrated
precision reference. It is guaranteed monotonic and has built in
rail-to-rail output buffers that can source or sink up to 20 mA.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220225130129.69-2-nuno.sa@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

An ADC is often used to measure other quantities indirectly.
This binding describe one case, the measurement of a temperature
through a temperature transducer (either voltage or current).
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-11-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

An ADC is often used to measure other quantities indirectly. This
binding describe one case, the measurement of a temperature through the
voltage across an RTD resistor such as a PT1000.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-10-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

A temperature transducer is a device that converts a thermal quantity
into any other physical quantity. This patch adds support for
temperature to voltage (like the LTC2997) and temperature to current
(like the AD590) linear transducers.
In both cases these are assumed to be connected to a voltage ADC.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-9-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

An RTD (Resistance Temperature Detector) is a kind of temperature
sensor used to get a linear voltage to temperature reading within a
give range (usually 0 to 100 degrees Celsius). Common types of RTDs
include PT100, PT500, and PT1000.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-8-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The iio-rescale driver supports various combinations of scale types and
offsets. These can often result in large integer multiplications. Make
sure these calculations are done right by adding a set of kunit test
cases that build on top of iio-test-format.

To run these tests, add the following to .kunitconfig
	$ cat .kunitconfig
	CONFIG_IIO=y
	CONFIG_IIO_RESCALE_KUNIT_TEST=y
	CONFIG_KUNIT=y

Then run:
	$ ./tools/testing/kunit/kunit.py run --kunitconfig .kunitconfig
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-7-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Reduce the risk of integer overflow by doing the scale calculation on
a 64-bit integer. Since the rescaling is only performed on *val, reuse
the IIO_VAL_FRACTIONAL_LOG2 case.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-6-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The approximation caused by integer divisions can be costly on smaller
scale values since the decimal part is significant compared to the
integer part. Switch to an IIO_VAL_INT_PLUS_NANO scale type in such
cases to maintain accuracy.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-5-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This is a preparatory change required for the addition of temperature
sensing front ends.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-4-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Some ADCs use IIO_VAL_INT_PLUS_{NANO,MICRO} scale types.
Add support for these to allow using the iio-rescaler with them.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-3-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In preparation for the addition of kunit tests, expose the logic
responsible for combining channel scales.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-2-liambeguin@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add support for K Band Downconverter with Integrated
Fractional-N PLL and VCO.
More info:
https://www.analog.com/en/products/admv4420.htmlSigned-off-by: Cristian Pop <cristian.pop@analog.com>
Link: https://lore.kernel.org/r/20220223130808.13352-2-cristian.pop@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add device tree bindings for the ADMV4420 K band downconverter.
Signed-off-by: Cristian Pop <cristian.pop@analog.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220223130808.13352-1-cristian.pop@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add myself as maintainer for the ADA4250 driver.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220223120112.8067-3-antoniu.miclaus@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADA4250 is an instrumentation amplifier with SPI/pin-strap
progammable gains that is optimized for ultra-low power systems.
With a minimum supply voltage of 1.7V, 26uA of quiescent current,
a shutdown mode, a sleep mode, and a fast wake up settling time,
ADA4250 can be power cycled on a battery powered system for even
futher savings.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220223120112.8067-2-antoniu.miclaus@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add device tree bindings for the ADA4250 driver.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220223120112.8067-1-antoniu.miclaus@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Remove unneeded blank lines where they separate the data type definitions
and the macros which are using them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-8-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Terminator entries are by definition should terminate the array.
Dropping comma make this enforced at compile time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-7-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

For the sake of symmetry and possible reuse in the future
extract adxl435_powerup() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-6-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

x86 boards may use ACPI HID "ADS0345" for adxl345 device.

Analog replied:
"ADS034X is not a valid PNP ID. ADS0345 would be.
I'm not aware that this ID is already taken.
Feel free to submit a mainline Linux input mailing list patch."

So add an ACPI match table for that accordingly.

Since ACPI device may not match to any I2C ID, use the name and type
directly from ACPI ID table in absence of I2C ID.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220222090009.2060-5-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-4-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

As a preparation to switch to use device properties, get rid of name
parameter in adxl345_core_probe(). Instead, choose it based on the type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-3-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In order to enable this driver on mode platforms, assign driver_data
field in the OF device ID table.

While at it, make sure that device type is not 0 which may be wrongly
interpreted by device property APIs in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-2-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220222090009.2060-1-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value and return
error if fails.

Fixes: fa659a40 ("iio: adc: twl6030-gpadc: Use devm_* API family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220224062849.3280966-1-jiasheng@iscas.ac.cnSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Maxim DS3502 is a 7 bit nonvolatile digital potentiometer.
Add DS3502 binding into trivial-devices.yaml.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-8-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The DS3502 is a 7-bit, nonvolatile digital potentiometer featuring
an output voltage range of up to 15.5V. DS3502 support is added
into existing DS1803 driver.

Datasheet: https://datasheets.maximintegrated.com/en/ds/DS3502.pdfSigned-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-7-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Added function pointer in the device specific structure to
call the appropriate device read_raw function, so that the
other type of devices with different read method can be
handled.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-6-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Using firmware provided data to get the device specific
structure if not available fall back to id->driver_data.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-5-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Adding each device wiper count and channel information into
device private data.
Utilizing addr member of struct iio_chan_spec to get the
wiper register address so that the value can be read or write
to the same address.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-4-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Adding available functionality for DS1803 driver which
will show the minimum, step and maximum values that the
driver can accepts through sysfs entry.
Now using the max value present in avail array instead of chip
type specific macro to make the driver flexible to add other
type of potentiometer with different max position value.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-3-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix following checkpatch.pl check by removing blank space.
CHECK: Alignment should match open parenthesis.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220223163525.13399-2-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Clang warns:

  drivers/iio/accel/adxl367.c:887:2: error: variable 'handled' is uninitialized when used here [-Werror,-Wuninitialized]
          handled |= adxl367_push_event(indio_dev, status);
          ^~~~~~~
  drivers/iio/accel/adxl367.c:879:14: note: initialize the variable 'handled' to silence this warning
          bool handled;
                      ^
                       = 0
  1 error generated.

This should have used '=' instead of '|='; make that change to resolve
the warning.

Fixes: cbab791c ("iio: accel: add ADXL367 driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1605Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220224211034.625130-1-nathan@kernel.orgSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This error path needs to call the mutex_unlock(&st->lock) before
returning.

Fixes: cbab791c ("iio: accel: add ADXL367 driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220224150228.GB6856@kiliSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use devm_delayed_work_autocancel() instead of hand writing it. This is
less verbose and saves a few lines of code.

devm_delayed_work_autocancel() uses devm_add_action() instead of
devm_add_action_or_reset(). This is fine, because if the underlying memory
allocation fails, no work has been scheduled yet. So there is nothing to
undo.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2626e6a057e40cd2271ef0e5f81d12e607bad5b4.1644776929.git.christophe.jaillet@wanadoo.frSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add myself as maintainer for the ADMV1014 driver.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220215081216.67706-4-antoniu.miclaus@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add documentation for the use of the Digital Attenuator gain.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220215081216.67706-3-antoniu.miclaus@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>