DPU runtime resume will request for a min vote on the AXI bus as
it is a necessary step before turning ON the AXI clock.

The change does below
1) Move the icc path set before requesting runtime get_sync.
2) remove the dependency of hw catalog for min ib vote
as it is initialized at a later point.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

When putting iMX5 into suspend, the following flow is
observed:

[   70.023427] [<c07755f0>] (msm_atomic_commit_tail) from [<c06e7218>]
(commit_tail+0x9c/0x18c)
[   70.031890] [<c06e7218>] (commit_tail) from [<c0e2920c>]
(drm_atomic_helper_commit+0x1a0/0x1d4)
[   70.040627] [<c0e2920c>] (drm_atomic_helper_commit) from
[<c06e74d4>] (drm_atomic_helper_disable_all+0x1c4/0x1d4)
[   70.050913] [<c06e74d4>] (drm_atomic_helper_disable_all) from
[<c0e2943c>] (drm_atomic_helper_suspend+0xb8/0x170)
[   70.061198] [<c0e2943c>] (drm_atomic_helper_suspend) from
[<c06e84bc>] (drm_mode_config_helper_suspend+0x24/0x58)

In the i.MX5 case, priv->kms is not populated (as i.MX5 does not use any
of the Qualcomm display controllers), causing a NULL pointer
dereference in msm_atomic_commit_tail():

[   24.268964] 8<--- cut here ---
[   24.274602] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
[   24.283434] pgd = (ptrval)
[   24.286387] [00000000] *pgd=ca212831
[   24.290788] Internal error: Oops: 17 [#1] SMP ARM
[   24.295609] Modules linked in:
[   24.298777] CPU: 0 PID: 197 Comm: init Not tainted 5.11.0-rc2-next-20210111 #333
[   24.306276] Hardware name: Freescale i.MX53 (Device Tree Support)
[   24.312442] PC is at msm_atomic_commit_tail+0x54/0xb9c
[   24.317743] LR is at commit_tail+0xa4/0x1b0

Fix the problem by calling drm_mode_config_helper_suspend/resume()
only when priv->kms is available.

Fixes: ca8199f1 ("drm/msm/dpu: ensure device suspend happens during PM sleep")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

If GPU components have failed to bind, shutdown callback would fail with
the following backtrace. Add safeguard check to stop that oops from
happening and allow the board to reboot.

[   66.617046] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[   66.626066] Mem abort info:
[   66.628939]   ESR = 0x96000006
[   66.632088]   EC = 0x25: DABT (current EL), IL = 32 bits
[   66.637542]   SET = 0, FnV = 0
[   66.640688]   EA = 0, S1PTW = 0
[   66.643924] Data abort info:
[   66.646889]   ISV = 0, ISS = 0x00000006
[   66.650832]   CM = 0, WnR = 0
[   66.653890] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000107f81000
[   66.660505] [0000000000000000] pgd=0000000100bb2003, p4d=0000000100bb2003, pud=0000000100897003, pmd=0000000000000000
[   66.671398] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[   66.677115] Modules linked in:
[   66.680261] CPU: 6 PID: 352 Comm: reboot Not tainted 5.11.0-rc2-00309-g79e3faa7 #38
[   66.688473] Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
[   66.695347] pstate: 60400005 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[   66.701507] pc : msm_atomic_commit_tail+0x78/0x4e0
[   66.706437] lr : commit_tail+0xa4/0x184
[   66.710381] sp : ffff8000108f3af0
[   66.713791] x29: ffff8000108f3af0 x28: ffff418c44337000
[   66.719242] x27: 0000000000000000 x26: ffff418c40a24490
[   66.724693] x25: ffffd3a842a4f1a0 x24: 0000000000000008
[   66.730146] x23: ffffd3a84313f030 x22: ffff418c444ce000
[   66.735598] x21: ffff418c408a4980 x20: 0000000000000000
[   66.741049] x19: 0000000000000000 x18: ffff800010710fbc
[   66.746500] x17: 000000000000000c x16: 0000000000000001
[   66.751954] x15: 0000000000010008 x14: 0000000000000068
[   66.757405] x13: 0000000000000001 x12: 0000000000000000
[   66.762855] x11: 0000000000000001 x10: 00000000000009b0
[   66.768306] x9 : ffffd3a843192000 x8 : ffff418c44337000
[   66.773757] x7 : 0000000000000000 x6 : 00000000a401b34e
[   66.779210] x5 : 00ffffffffffffff x4 : 0000000000000000
[   66.784660] x3 : 0000000000000000 x2 : ffff418c444ce000
[   66.790111] x1 : ffffd3a841dce530 x0 : ffff418c444cf000
[   66.795563] Call trace:
[   66.798075]  msm_atomic_commit_tail+0x78/0x4e0
[   66.802633]  commit_tail+0xa4/0x184
[   66.806217]  drm_atomic_helper_commit+0x160/0x390
[   66.811051]  drm_atomic_commit+0x4c/0x60
[   66.815082]  drm_atomic_helper_disable_all+0x1f4/0x210
[   66.820355]  drm_atomic_helper_shutdown+0x80/0x130
[   66.825276]  msm_pdev_shutdown+0x14/0x20
[   66.829303]  platform_shutdown+0x28/0x40
[   66.833330]  device_shutdown+0x158/0x330
[   66.837357]  kernel_restart+0x40/0xa0
[   66.841122]  __do_sys_reboot+0x228/0x250
[   66.845148]  __arm64_sys_reboot+0x28/0x34
[   66.849264]  el0_svc_common.constprop.0+0x74/0x190
[   66.854187]  do_el0_svc+0x24/0x90
[   66.857595]  el0_svc+0x14/0x20
[   66.860739]  el0_sync_handler+0x1a4/0x1b0
[   66.864858]  el0_sync+0x174/0x180
[   66.868269] Code: 1ac020a0 2a000273 eb02007f 54ffff01 (f9400285)
[   66.874525] ---[ end trace 20dedb2a3229fec8 ]---

Fixes: 9d5cbf5f ("drm/msm: add shutdown support for display platform_driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We have seen a couple cases where low memory situations cause something
bad to happen, followed by a flood of these messages obscuring the root
cause.  Lets ratelimit the dmesg spam so that next time it happens we
don't lose the kernel traces leading up to this.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

While passing the A530-specific lm_setup func to A530 and A540
to !A530 was fine back when only these two were supported, it
certainly is not a good idea to send A540 specifics to smaller
GPUs like A508 and friends.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

In commit 9fc41843 ("drm/msm/dp: unplug interrupt missed after
irq_hpd handler") we dropped a reset of the aux phy during aux transfers
because resetting the phy during active communication caused us to miss
an hpd irq in some cases. Unfortunately, we also dropped the part of the
code that changes the aux phy tuning when an aux transfer fails due to a
timeout. That part of the code was calling into the phy driver to
reconfigure the aux TX swing controls, working around poor channel
quality. Let's restore this phy setting code so that aux channel
communication is more reliable.

Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Fixes: 9fc41843 ("drm/msm/dp: unplug interrupt missed after irq_hpd handler")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!

Based on 362cadf3 ("drm/msm/dsi_pll_10nm: Fix variable usage for
pll_lockdet_rate")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 7nm:
remove the TODO by simply using that variable. This is a copy of
196145eb ("drm/msm/dsi_pll_10nm: Solve TODO for multiplier frac_bits
assignment").
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Fix setting min/max DSI PLL rate for the V4.1 7nm DSI PLL (used on
sm8250). Current code checks for pll->type before it is set (as it is
set in the msm_dsi_pll_init() after calling device-specific functions.

Cc: Jonathan Marek <jonathan@marek.ca>
Fixes: 1ef7c99d ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

When running the latest kernel on an sc7180 with KASAN I got this
splat:
  BUG: KASAN: slab-out-of-bounds in a6xx_gpu_init+0x618/0x644
  Read of size 4 at addr ffffff8088f36100 by task kworker/7:1/58
  CPU: 7 PID: 58 Comm: kworker/7:1 Not tainted 5.11.0+ #3
  Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
  Workqueue: events deferred_probe_work_func
  Call trace:
   dump_backtrace+0x0/0x3a8
   show_stack+0x24/0x30
   dump_stack+0x174/0x1e0
   print_address_description+0x70/0x2e4
   kasan_report+0x178/0x1bc
   __asan_report_load4_noabort+0x44/0x50
   a6xx_gpu_init+0x618/0x644
   adreno_bind+0x26c/0x438

This is because the speed bin is defined like this:
  gpu_speed_bin: gpu_speed_bin@1d2 {
    reg = <0x1d2 0x2>;
    bits = <5 8>;
  };

As you can see the "length" is 2 bytes. That means that the nvmem
subsystem allocates only 2 bytes. The GPU code, however, was casting
the pointer allocated by nvmem to a (u32 *) and dereferencing. That's
not so good.

Let's fix this to just use the nvmem_cell_read_u16() accessor function
which simplifies things and also gets rid of the splat.

Let's also put an explicit conversion from little endian in place just
to make things clear. The nvmem subsystem today is assuming little
endian and this makes it clear. Specifically, the way the above sc7180
cell is interpreted:

NVMEM:
 +--------+--------+--------+--------+--------+
 | ...... | 0x1d3  | 0x1d2  | ...... | 0x000  |
 +--------+--------+--------+--------+--------+
              ^       ^
             msb     lsb

You can see that the least significant data is at the lower address
which is little endian.

NOTE: someone who is truly paying attention might wonder about me
picking the "u16" version of this accessor instead of the "u8" (since
the value is 8 bits big) or the u32 version (just for fun). At the
moment you need to pick the accessor that exactly matches the length
the cell was specified as in the device tree. Hopefully future
patches to the nvmem subsystem will fix this.

Fixes: fe7952c6 ("drm/msm: Add speed-bin support to a618 gpu")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Most a6xx targets have security issues that were fixed with new versions
of the microcode(s). Make sure that we are booting with a safe version of
the microcode for the target and print a message and error if not.

v2: Add more informative error messages and fix typos
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The cleanup patch broke a6xx_gmu_clear_oob, fix it by adding the missing
bitshift operation.

Fixes: 555c50a4 ("drm/msm: Clean up GMU OOB set/clear handling")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We don't need to make up custom lock classes here, we can simply use
mutex_lock_nested() and pass in the index of the crtc to the locking
APIs instead. This helps lockdep understand that these are really
different locks while avoiding having to allocate custom lockdep
classes.

Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Fixes: b3d91800 ("drm/msm: Fix race condition in msm driver with async layer updates")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

A missing semicolon here causes my external display to stop working.
Indeed, missing the semicolon on the return statement leads to
dp_panel_update_tu_timings() not existing because the compiler thinks
it's part of the return statement of a void function, so it must not be
important.

  $ ./scripts/bloat-o-meter before.o after.o
  add/remove: 1/1 grow/shrink: 0/1 up/down: 7400/-7540 (-140)
  Function                                     old     new   delta
  dp_panel_update_tu_timings                     -    7400   +7400
  _dp_ctrl_calc_tu.constprop                 18024   17900    -124
  dp_panel_update_tu_timings.constprop        7416       -   -7416
  Total: Before=54440, After=54300, chg -0.26%

Add a semicolon so this function works like it used to.

Cc: Sean Paul <sean@poorly.run>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: freedreno@lists.freedesktop.org
Cc: Lee Jones <lee.jones@linaro.org>
Fixes: cc9014bf ("drm/msm/dp/dp_ctrl: Move 'tu' from the stack to the heap")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

DP_SW_RESET is the global SW reset that is used to initialize DP
controller. If DP_SW_RESET executed during connection setup,
two HPD related side effects may occurred,
1) pending HPD interrupts cleared unexpected
2) re start debounce logic which trigger another interrupt
This patch only issue DP_SW_RESET at boot up and pm_resume.
This patch also reinit video_comp before configure dp controller
to avoid missing VIDEO_READY interrupt.

Fixes: 9fc41843 ("drm/msm/dp: unplug interrupt missed after irq_hpd handler")
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

In moving code around, we ended up using the same pointer to
copy_from_user() the relocs tables as we used for the cmd table
entry, which is clearly not right.  This went unnoticed because
modern mesa on non-ancent kernels does not actually use relocs.
But this broke ancient mesa on modern kernels.
Reported-by: Emil Velikov <emil.velikov@collabora.com>
Fixes: 20224d71 ("drm/msm/submit: Move copy_from_user ahead of locking bos")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>

The maximum mdp clock rate on msm8974v2 is 320MHz. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

remove unneeded variable: "rc".
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

DRM_DEV_ERROR should be used across this entire source: convert the
pr_err prints to the first as a cleanup.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The PLL_LOCKDET_RATE_1 was being programmed with a hardcoded value
directly, but the same value was also being specified in the
dsi_pll_regs struct pll_lockdet_rate variable: let's use it!
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The number of fractional registers bits is known and already set in
the frac_bits variable of the dsi_pll_config struct here in 10nm:
remove the TODO by simply using that variable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

In function dsi_pll_calc_dec_frac we are calculating the decimal
div start parameter by dividing the decimal multiple by the
fractional multiplier: the remainder of that operation is stored
to then get programmed to the fractional divider registers of
the PLL.

It's useless to call div_u64_rem to get the remainder and *then*
call div_u64 to get the division result, as the first is already
giving that result: let's fix it by just caring about the result
of div_u64_rem.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

1. Trigger the unplug event in msm_dp_display_disable() to shutdown audio
   properly.
2. Reset the completion before signal the disconnect event.

Fixes: 158b9aa7 ("drm/msm/dp: wait for audio notification before disabling clocks")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

fix semicolon.cocci warnings:
drivers/gpu/drm/msm/dp/dp_ctrl.c:1161:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Rob Clark <robdclark@chromium.org>

fix semicolon.cocci warnings:
drivers/gpu/drm/msm/disp/dpu1/dpu_kms.c:752:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Fix below warnings reported by coccicheck:
./drivers/gpu/drm/msm/msm_gem.c:991:3-9: WARNING: NULL check before some
freeing functions is not needed.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Lockdep complains about an AA deadlock when rebooting the device.

base-commit: 19c329f6

============================================
WARNING: possible recursive locking detected
5.4.91 #1 Not tainted
--------------------------------------------
reboot/5213 is trying to acquire lock:
ffffff80d13391b0 (&kms->commit_lock[i]){+.+.}, at: lock_crtcs+0x60/0xa4

but task is already holding lock:
ffffff80d1339110 (&kms->commit_lock[i]){+.+.}, at: lock_crtcs+0x60/0xa4

other info that might help us debug this:
Possible unsafe locking scenario:

CPU0
----
lock(&kms->commit_lock[i]);
lock(&kms->commit_lock[i]);

*** DEADLOCK ***

May be due to missing lock nesting notation

6 locks held by reboot/5213:
__arm64_sys_reboot+0x148/0x2a0
device_shutdown+0x10c/0x2c4
drm_atomic_helper_shutdown+0x48/0xfc
modeset_lock+0x120/0x24c
lock_crtcs+0x60/0xa4

stack backtrace:
CPU: 4 PID: 5213 Comm: reboot Not tainted 5.4.91 #1
Hardware name: Google Pompom (rev1) with LTE (DT)
Call trace:
dump_backtrace+0x0/0x1dc
show_stack+0x24/0x30
dump_stack+0xfc/0x1a8
__lock_acquire+0xcd0/0x22b8
lock_acquire+0x1ec/0x240
__mutex_lock_common+0xe0/0xc84
mutex_lock_nested+0x48/0x58
lock_crtcs+0x60/0xa4
msm_atomic_commit_tail+0x348/0x570
commit_tail+0xdc/0x178
drm_atomic_helper_commit+0x160/0x168
drm_atomic_commit+0x68/0x80

This is because lockdep thinks all the locks taken in lock_crtcs() are
the same lock, when they actually aren't. That's because we call
mutex_init() in msm_kms_init() and that assigns one static key for every
lock initialized in this loop. Let's allocate a dynamic number of
lock_class_keys and assign them to each lock so that lockdep can figure
out an AA deadlock isn't possible here.

Fixes: b3d91800 ("drm/msm: Fix race condition in msm driver with async layer updates")
Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that the bug is fixed in the minimal way for stable, go make the
code table-driven.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that we're not racing with GPU setup, also fix races of timestamps
against other timestamps.  In freedreno CI, we were seeing this path trigger
timeouts on setting the GMU bit, producing:

[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0

and this triggered especially on the first set of tests right after
boot (it's probably easier to lose the race than one might think,
given that we start many tests in parallel, and waiting for NFS to
page in code probably means that lots of tests hit the same point of
screen init at the same time).  As of this patch, the message seems to
have completely gone away.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5 ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

We were using the same force-poweron bit in the two codepaths, so they
could race to have one of them lose GPU power early.

freedreno CI was seeing intermittent errors like:
[drm:_a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set GPU_SET: 0x0
and this issue could have contributed to it.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 4b565ca5 ("drm/msm: Add A6XX device support")
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Before the offending commit in msm_atomic_commit_tail wait_flush was
called once per frame, after the commit was submitted. After it
wait_flush is also called at the beginning to ensure previous
potentially async commits are done.

For cmd panels the source of wait_flush is a ping-pong irq notifying
a completion. The completion needs to be notified with complete_all so
multiple waiting parties (new async committers) can proceed.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Suggested-by: Rob Clark <robdclark@gmail.com>
Fixes: 2d99ced7 ("drm/msm: async commit support")
Signed-off-by: Rob Clark <robdclark@chromium.org>

The previous registers were *almost* correct, but instead of
PHYs, they were pointing at DSI PLLs, resulting in the PHY id
autodetection failing miserably.

Fixes: dcefc117 ("drm/msm/dsi: Add support for msm8x94")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

SM8250 has quite unique qseed lut type: qseed3lite, which is a
lightweight version of qseed3 scaler.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

There is HPD unplug interrupts missed at scenario of an irq_hpd
followed by unplug interrupts with around 10 ms in between.
Since both AUX_SW_RESET and DP_SW_RESET clear pending HPD interrupts,
irq_hpd handler should not issues either aux or sw reset to avoid
following unplug interrupt be cleared accidentally. This patch
also postpone handling of irq_hpd until connected state if it
happened at connection pending state.

Changes in V2:
-- add postpone handling of irq_hpd until connected state
-- check DP_TRAINING_1 instead of DP_TRAINING_NONE
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The call to dpu_encoder_phys_cmd_prepare_for_kickoff is useless as
it's unused because the serialize_wait4pp variable is never set to
true by .. anything, literally: remove the call.
While at it, also reduce indentation by inverting the check for
dpu_encoder_phys_cmd_is_master.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

When configuring the tearcheck, the parameters for the engine were
being set mostly as they should've been, but then it wasn't getting
configured to get the vsync indication from the TE GPIO input
because it was assumed that autorefresh could be enabled:
since a previous commit makes sure to disable the autorefresh bit
when committing to the cmd engine, it is now safe to just enable
the vsync pin input at tearcheck setup time (instead of erroneously
never enabling it).

Also, set the right sync_cfg_height to enable the DPU auto-generated
TE signal in order to avoid stalls in the event that we miss one
external TE signal: this will still trigger recovery mechanisms in
case the display is really unreachable.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

When a command mode display is used, it may be retaining the bootloader
configuration which, in most of the cases, enables the autorefresh
feature in order to keep the splash up.

Since there is no autorefresh management in this driver, wire up the
autorefresh ops in the dpu_hw_pingpong and disable the feature when
preparing for cmd commit: instead of disabling it when initializing
the command mode, this road was chosen as to open future possibility
of enabling and managing the autorefresh feature in the driver.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The DSPP_BLK macro was ad-hoc made for SC7180, but this is wrong
because not all of the DPU DSPP versions can use the same DSPP block
configuration, and not all of them have got the same features.

For this reason, add two more params to the DSPP_BLK macro, so that
it is possible to specify the feature mask and the sblk config for
each DSPP.

Fixes: 4259ff7a ("drm/msm/dpu: add support for pcc color block in dpu driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Not all DPU interface sub-block versions need the same value for
prog_fetch_lines_worst_case: add this to the INTF_BLK macro, so
that it becomes possible to vary it for other INTF versions.

For example, this is needed to implement support for older SoCs,
like MSM8998 and SDM630/660 and most probably will also be needed
for future SoCs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Not all DPU versions that are supported in this driver are supposed
to have a 8-Levels VIG QoS setting.
Move this flag to SDM845 and SC7180 specific masks.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>