Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Set GPIO bits to pull the pins connected to LEDs for lower power mode.
We want all LEDs off when devices are in suspend.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Amit Walambe <amit.walambe@eurotech.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:

1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
   non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>

The irq_chip is not yet registered, so no default irq_chip.mask_ack(),
which we have to handle it correctly manually here.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Since PMIC INT pin is a special pin of CPU, the status of PMIC INT pin needs
to be cleared after PMIC IRQ occured. Now append the clear operation in
irq chip handler.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Marvell MMP2 (aka ARMADA610) is a SoC based on PJ4 core. It's
ARMv6 compatible.  Support basic interrupt handler and timer,
and basic support for MMP2 based FLINT platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Gavin Gu <gavin.gu@marvell.com>
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Gavin Gu <gavin.gu@marvell.com>
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Also remove a trailing whitespace while being there.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Add some safety check for CONFIG_PM around zeus_power_off(). Without
it linking can fail like this:

arch/arm/mach-pxa/built-in.o: In function `zeus_power_off':
e800.c:(.text+0x2bc8): undefined reference to `pxa27x_cpu_suspend'
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This function gets only called from scoop_suspend() and scoop_resume() which are
only built in if we have CONFIG_PM set. Make it the same for check_scoop_reg().

This fixes the following warning:
arch/arm/common/scoop.c:143: warning: ‘check_scoop_reg’ defined but not used
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Edwin Peer <epeer@tmtservices.co.za>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The IRQs for card detect and status change are currently hardcoded in
SA1111 PCMCIA driver, which can be actually obtained from the .irq[]
from 'struct sa1111_dev' to keep it generic.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.

IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.

IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

These IRQ definitions related to LOCOMO are never referenced anywhere,
thus could be safely removed.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Now most (if not all) PXA platforms have been switched to the new MFP
API, it's rather safe to remove these unnecessary pxa_gpio_mode() calls
in pxa2xx-ac97-lib.c now.

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Missing AC97 pin configurations are added where pxa_set_ac97_info() are
called for all pxa25x/pxa27x platforms. Where no exact configuration is
provided, use the default as in sound/arm/pxa2xx-ac97-lib.c

Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>