The DRE controls on wm5110 should return a value of 1 if the DRE state
is actually changed, update to fix this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The preloader controls on ADSP should return a value of 1 if the
preloader value was changed, update to correct this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220621102041.1713504-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Javier Martinez Canillas <javierm@redhat.com>:

This series contains fixes for a few issues found while testing the recent
support for drivers to define bulk read/write callbacks in regmap_config.

I tested this with drivers/gpu/drm/solomon/ssd130x-spi.c, by converting it
to use this new API instead of defining its own regmap bus for bulk write.

Patch #1 and patch #2 are fixes for regresions introduced by that commit
and patch #3 adds regmap_config provided bulk write support to functions
regmap_noinc_write() and regmap_bulk_write(), that were missed.

Update Banajit's email address from codeaurora.org to quicinc.com, as
codeaurora.org is not in use anymore.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220617210230.7685-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.

In order to:
  1. prevent BCLK from turning on by other component.
  2. keep BCLK and LRCLK being present at the same time

This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.

Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20220615045643.3137287-1-judyhsiao@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There are some functions that were missed by commit d77e7456 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.

The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.

Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-4-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e7456 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.

But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.

Also is a fragile assumption to make so is better to make it fail earlier.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-3-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e7456 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.

Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.

Fixes: d77e7456 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220616073435.1988219-2-javierm@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

The enablement of IMR-based DSP boot helped reduce resume latency, but
unfortunately the context is not saved in S4 and S5 which leads to
multiple reports of boot failures.

This patchset forces a full firmware reload/reboot when resuming from
S4/S5 and restores functionality.

Commit 288fad2f ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
modified the PCM path only, but left the compressed data patch using an
obsolete option.
Move the functionality in a helper that can be called for both PCM and
compressed data.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Fixes: 288fad2f ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201953.130876-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.

Make sure regular boot with firmware download is used for S4 and S5.

BugLink: https://github.com/thesofproject/sof/issues/5892
Fixes: 5fb5f511 ("ASoC: SOF: Intel: hda-loader: add IMR restore support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The existing code only deals with S0 and S3, let's start adding S1 and S2.

No functional change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220616201818.130802-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This should return PTR_ERR() instead of IS_ERR().

Fixes: e0100bfd ("ASoC: SOF: mediatek: Add mt8186 ipc support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/YqmWIK8sTj578OJP@kiliSigned-off-by: Mark Brown <broonie@kernel.org>

The "wlf,spkvdd-ena" GPIO needed by the bytcr_wm5102 driver
is made available through a gpio-lookup table.

This gpio-lookup table is registered by drivers/mfd/arizona-spi.c, which
may get probed after the bytcr_wm5102 driver.

If the gpio-lookup table has not registered yet then the gpiod_get()
will return -ENOENT. Treat -ENOENT as -EPROBE_DEFER to still keep
things working in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220612155652.107310-1-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Keyon Jie was a key contributor to the Intel ASoC and SOF Intel
drivers, but he's moved on to a different role within Intel. We wish
him all the best in his new endeavors.

Bard Liao, Kai Vehmanen, Ranjani Sridharan and Peter Ujfalusi have
been involved in the Intel multi-maintainer team, it's time to update
the MAINTAINERS entry to reflect their contributions and clarify their
role.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220610214313.42903-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Currently wcd938x_*_put() unconditionally report that the value of the
control changed, resulting in spurious events being generated. Return 0 in
that case instead as we should. There is still an issue in the compander
control which is a bit more complex.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220603122526.3914942-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The slimbus mux put operation unconditionally reports a change in value
which means that spurious events are generated. Fix this by exiting early
in that case.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220603124609.4024666-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Currently in slim_rx_mux_put, an RX channel gets added to a new list
even if it is already in one. This can mess up links and make either
it, the new list head, or both, get linked to the wrong entries.
This can cause an entry to link to itself which in turn ends up
making list_for_each_entry in other functions loop infinitely.
To avoid issues, always remove the RX channel from any list it's in
before adding it to a new list.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20220606152226.149164-1-y.oudjana@protonmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

prepare callback can be called multiple times, so unprepare the stream
if its already prepared.

Without this DSP is not happy to setting the params on a already
prepared graph.

Fixes: 9b4fe0f1 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Reported-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220610144818.511797-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 81da8a0b ("ASoC: remove codec hw_write/control_data") removed
use of hw_write_t in struct snd_soc_codec, but it left type definition.
Fully clean it up.

Fixes: 81da8a0b ("ASoC: remove codec hw_write/control_data")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220610124420.4160986-1-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use correct type for parsing UUIDs, this eliminates warning present,
when compiling with W=1.

Fixes: 34ae2cd5 ("ASoC: Intel: avs: Add topology parsing infrastructure")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220610124257.4160658-1-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Move the size checks prior to allocating memory as these checks do not need
the data to be allocated and in case of an error we would not need to free
the allocation.

The max size must not be less than the size of
struct sof_ipc_ctrl_data + struct sof_abi_hdr as the ABI header needs to
be present under all circumstances.
The check was incorrectly used or between the two size checks.

Fixes: b5cee8fe ("ASoC: SOF: topology: Make control parsing IPC agnostic")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610084735.19397-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Update the comment for the cl_dsp_init() to clarify what is done by the
function and use the chip->init_core_mask instead of BIT(0) when
unstalling/running the init core.

Complements: 2a68ff84 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-4-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The hda_dsp_enable_core() is powering up _and_ unstall the core in one
call while the first step of the firmware loading  must not unstall the
core.
The core can be unstalled only after the set cpb_cfp and the configuration
of the IPC register for the ROM_CONTROL message.

Complements: 2a68ff84 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-3-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The hda_dsp_core_power_up() needs to be exposed so that it can be used in
hda-loader.c to correct the boot flow.
The first step must not unstall the core, it should only power up the
core(s).

Add sanity check for the core_mask while exposing it to be safe.

Complements: 2a68ff84 ("ASoC: SOF: Intel: hda: Revisit IMR boot sequence")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220609085949.29062-2-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Renesas is the only user of ak4613 on upstream for now, and
commit f28dbaa9 ("ASoC: ak4613: add TDM256 support")
added TDM256 support. Renesas tested part of it, because of
board connection.

It was assuming ak4613 is probed via Audio-Graph-Card, but it
might be probed via Simple-Audio-Card either.
It will indicates WARNING in such case. This patch fixup it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87h74v29f7.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

While testing fixes for SoundWire race conditions initially reported
in [1], I found additional issues in codec drivers. When the order in
which drivers are probed is changed, multiple errors are reported,
from unbalanced pm_runtime_enable() calls to invalid mutex lock magic
numbers, workqueues not initialized and missing resume sequences.

In 'nominal' usages, there is no change of functionality, this is just
a first step to test random device/driver bind/unbind sequences.

Important note: these changes only touch Intel-based platforms, I
don't have any background and ability to test on Qualcomm-based
devices.

[1] https://lore.kernel.org/alsa-devel/d0559e97-c4a0-b817-428c-d3e305390270@linux.intel.com/

Pierre-Louis Bossart (7):
  ASoC: Realtek/Maxim SoundWire codecs: disable pm_runtime on remove
  ASoC: rt711-sdca-sdw: fix calibrate mutex initialization
  ASoC: Intel: sof_sdw: handle errors on card registration
  ASoC: rt711: fix calibrate mutex initialization
  ASoC: rt7*-sdw: harden jack_detect_handler
  ASoC: codecs: rt700/rt711/rt711-sdca: initialize workqueues in probe
  ASoC: codecs: rt700/rt711/rt711-sdca: resume bus/codec in
    .set_jack_detect

 sound/soc/codecs/max98373-sdw.c   | 12 +++++++-
 sound/soc/codecs/rt1308-sdw.c     | 11 +++++++
 sound/soc/codecs/rt1316-sdw.c     | 11 +++++++
 sound/soc/codecs/rt5682-sdw.c     |  5 ++-
 sound/soc/codecs/rt700-sdw.c      |  6 +++-
 sound/soc/codecs/rt700.c          | 30 +++++++++++-------
 sound/soc/codecs/rt711-sdca-sdw.c |  9 +++++-
 sound/soc/codecs/rt711-sdca.c     | 40 ++++++++++++------------
 sound/soc/codecs/rt711-sdw.c      |  9 +++++-
 sound/soc/codecs/rt711.c          | 40 ++++++++++++------------
 sound/soc/codecs/rt715-sdca-sdw.c | 12 ++++++++
 sound/soc/codecs/rt715-sdw.c      | 12 ++++++++
 sound/soc/intel/boards/sof_sdw.c  | 51 ++++++++++++++++++-------------
 13 files changed, 169 insertions(+), 79 deletions(-)

--
2.34.1

We currently report that range controls accept a range of 0..(max-min) but
accept writes in the range 0..(max-min+1). Remove that extra +1.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220604105246.4055214-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The .set_jack_detect() codec component callback is invoked during card
registration, which happens when the machine driver is probed.

The issue is that this callback can race with the bus suspend/resume,
and IO timeouts can happen. This can be reproduced very easily if the
machine driver is 'blacklisted' and manually probed after the bus
suspends. The bus and codec need to be re-initialized using pm_runtime
helpers.

Previous contributions tried to make sure accesses to the bus during
the .set_jack_detect() component callback only happen when the bus is
active. This was done by changing the regcache status on a component
remove. This is however a layering violation, the regcache status
should only be modified on device probe, suspend and resume. The
component probe/remove should not modify how the device regcache is
handled. This solution also didn't handle all the possible race
conditions, and the RT700 headset codec was not handled.

This patch tries to resume the codec device before handling the jack
initializations. In case the codec has not yet been initialized,
pm_runtime may not be enabled yet, so we don't squelch the -EACCES
error code and only stop the jack information. When the codec reports
as attached, the jack initialization will proceed as usual.

BugLink: https://github.com/thesofproject/linux/issues/3643
Fixes: 7ad4d237 ('ASoC: rt711-sdca: Add RT711 SDCA vendor-specific driver')
Fixes: 899b1254 ('ASoC: rt711: add snd_soc_component remove callback')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The workqueues are initialized in the io_init functions, which isn't
quite right. In some tests, this leads to warnings throw from
__queue_delayed_work()

WARN_ON_FUNCTION_MISMATCH(timer->function, delayed_work_timer_fn);

Move all the initializations to the probe functions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Realtek headset codec drivers typically check if the card is
instantiated before proceeding with the jack detection.

The rt700, rt711 and rt711-sdca are however missing a check on the
card pointer, which can lead to NULL dereferences encountered in
driver bind/unbind tests.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Follow the same flow as rt711-sdca and initialize all mutexes at probe
time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

If the card registration fails, typically because of deferred probes,
the device properties added for headset codecs are not removed, which
leads to kernel oopses in driver bind/unbind tests.

We already clean-up the device properties when the card is removed,
this code can be moved as a helper and called upon card registration
errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In codec driver bind/unbind test, the following warning is thrown:

DEBUG_LOCKS_WARN_ON(lock->magic != lock)
...
[  699.182495]  rt711_sdca_jack_init+0x1b/0x1d0 [snd_soc_rt711_sdca]
[  699.182498]  rt711_sdca_set_jack_detect+0x3b/0x90 [snd_soc_rt711_sdca]
[  699.182500]  snd_soc_component_set_jack+0x24/0x50 [snd_soc_core]

A quick check in the code shows that the 'calibrate_mutex' used by
this driver are not initialized at probe time. Moving the
initialization to the probe removes the issue.

BugLink: https://github.com/thesofproject/linux/issues/3644Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When binding/unbinding codec drivers, the following warnings are
thrown:

[ 107.266879] rt715-sdca sdw:3:025d:0714:01: Unbalanced pm_runtime_enable!
[  306.879700] rt711-sdca sdw:0:025d:0711:01: Unbalanced pm_runtime_enable!

Add a remove callback for all Realtek/Maxim SoundWire codecs and remove this
warning.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220606203752.144159-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Linux 5.19-rc1

Currently wm_adsp_fw_put() returns 0 rather than 1 when updating the value
of the control, meaning that no event is generated to userspace. Fix this
by setting the default return value to 1, the code already exits early with
a return value of 0 if the value is unchanged.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220603115003.3865834-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Currently the put() method for the deemphasis control returns 0 when a new
value is written to the control even if the value changed, meaning events
are not generated. Fix this, skip the work of updating the value when it is
unchanged and then return 1 after having done so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220603123937.4013603-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

If the audio CODEC is playing sound when the system is suspended,
it can be left in a state which throws the following error:

wm8962 3-001a: ASoC: error at soc_component_read_no_lock on wm8962.3-001a: -16

Once this error has occurred, the audio will not work again until rebooted.

Fix this by configuring SET_SYSTEM_SLEEP_PM_OPS.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220526182129.538472-1-aford173@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>