- 10 Jul, 2019 19 commits
-
-
Sean Wang authored
[ Upstream commit 880c2d4b ] Should only enable HW RX_2BYTE_OFFSET function in the case NET_IP_ALIGN equals to 2. Signed-off-by:
Mark Lee <mark-mc.lee@mediatek.com> Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sean Wang authored
[ Upstream commit 9e4f56f1 ] Should hw_feature as hardware capability flags to check if hardware LRO got support. Signed-off-by:
-
Young Xiao authored
[ Upstream commit 56cd0aef ] The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the sample period of a running perf_event. Consequently, when calculating the next event period, the new period will only be considered after the previous one has overflowed. This patch changes the calculation of the remaining event ticks so that they are offset if the period has changed. See commit 3581fe0e ("ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD") for details. Signed-off-by:
Young Xiao <92siuyang@gmail.com> Signed-off-by:
-
Yonglong Liu authored
[ Upstream commit 2e1f1648 ] When doing a loopback test at copper ports, the serdes loopback and the phy loopback will fail, because of the adjust link had not finished, and phy not ready. Adds sleep between adjust link and test process to fix it. Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Nikita Yushchenko authored
[ Upstream commit 62394708 ] When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error message is logged: failed to kill vid 0081/0 for device eth_cu_1000_4 This is caused by call from __vlan_vid_del() with vin set to zero, over call chain this results into _mv88e6xxx_port_vlan_del() called with vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL. On symmetric path moving port up, call goes through mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan() that returns -EOPNOTSUPP for zero vid. This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for zero vid, then this error code is explicitly cleared in dsa_slave_vlan_rx_kill_vid() and error message is no longer logged. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit f532beee ] Fixes gcc '-Wunused-but-set-variable' warning: arch/mips/kernel/uprobes.c: In function 'arch_uprobe_pre_xol': arch/mips/kernel/uprobes.c:115:17: warning: variable 'epc' set but not used [-Wunused-but-set-variable] It's never used since introduction in commit 40e084a5 ("MIPS: Add uprobes support.") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Paul Burton <paul.burton@mips.com> Cc: <ralf@linux-mips.org> Cc: <jhogan@kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: <linux-mips@vger.kernel.org> Signed-off-by:
-
Mike Marciniszyn authored
[ Upstream commit 35164f52 ] The command 'ibv_devinfo -v' reports 0 for max_mr. Fix by assigning the query values after the mr lkey_table has been built rather than early on in the driver. Fixes: 7b1e2099 ("IB/rdmavt: Move memory registration into rdmavt") Reviewed-by:
Josh Collier <josh.d.collier@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Mike Marciniszyn authored
[ Upstream commit 6d517353 ] By code inspection, the freeze_work is never canceled. Fix by adding a cancel_work_sync in the shutdown path to insure it is no longer running. Fixes: 77241056 ("IB/hfi1: add driver files") Reviewed-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Reviewed-by:
-
Mike Marciniszyn authored
[ Upstream commit 2abae62a ] The qpn allocation logic has a WARN_ON() that intends to detect the use of an index that will introduce bits in the lower order bits of the QOS bits in the QPN. Unfortunately, it has the following bugs: - it misfires when wrapping QPN allocation for non-QOS - it doesn't correctly detect low order QOS bits (despite the comment) The WARN_ON() should not be applied to non-QOS (qos_shift == 1). Additionally, it SHOULD test the qpn bits per the table below: 2 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^ [ 0, 0, 0, 0, 0, 0, sc0], qp bit 1 always 0* 3-4 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^ [ 0, 0, 0, 0, 0, sc1, sc0], qp bits [21] always 0 5-8 data VLs: [qp7, qp6, qp5, qp4, qp3, qp2, qp1] ^ [ 0, 0, 0, 0, sc2, sc1, sc0] qp bits [321] always 0 Fix by qualifying the warning for qos_shift > 1 and producing the correct mask to insure the above bits are zero without generating a superfluous warning. Fixes: 501edc42 ("IB/rdmavt: Correct warning during QPN allocation") Reviewed-by:
Kaike Wan <kaike.wan@intel.com> Signed-off-by:
-
Helge Deller authored
[ Upstream commit 6b98d913 ] Avoid such compiler warnings: arch/parisc/math-emu/cnv_float.h:71:27: warning: ‘<<’ in boolean context, did you mean ‘<’ ? [-Wint-in-bool-context] ((Dintp1(dint_valueA) << 33 - SGL_EXP_LENGTH) || Dintp2(dint_valueB)) arch/parisc/math-emu/fcnvxf.c:257:6: note: in expansion of macro ‘Dint_isinexact_to_sgl’ if (Dint_isinexact_to_sgl(srcp1,srcp2)) { Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 1c7ebeab ] BUG: memory leak unreferenced object 0xffff8881df48cda0 (size 16): comm "syz-executor.0", pid 5077, jiffies 4295994670 (age 22.280s) hex dump (first 16 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000d2d0d5fe>] parport_register_dev_model+0x141/0x6e0 [parport] [<00000000782f6dab>] 0xffffffffc15d1196 [<00000000d2ca6ae4>] platform_drv_probe+0x7e/0x100 [<00000000628c2a94>] really_probe+0x342/0x4d0 [<000000006874f5da>] driver_probe_device+0x8c/0x170 [<00000000424de37a>] __device_attach_driver+0xda/0x100 [<000000002acab09a>] bus_for_each_drv+0xfe/0x170 [<000000003d9e5f31>] __device_attach+0x190/0x230 [<0000000035d32f80>] bus_probe_device+0x123/0x140 [<00000000a05ba627>] device_add+0x7cc/0xce0 [<000000003f7560bf>] platform_device_add+0x230/0x3c0 [<000000002a0be07d>] 0xffffffffc15d0949 [<000000007361d8d2>] port_check+0x3b/0x50 [parport] [<000000004d67200f>] bus_for_each_dev+0x115/0x180 [<000000003ccfd11c>] __parport_register_driver+0x1f0/0x210 [parport] [<00000000987f06fc>] 0xffffffffc15d803e After commit 4e5a74f1 ("parport: Revert "parport: fix memory leak""), free_pardevice do not free par_dev->state, we should free it in error path of parport_register_dev_model before return. Reported-by:
Hulk Robot <hulkci@huawei.com> Fixes: 4e5a74f1 ("parport: Revert "parport: fix memory leak"") Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Vineet Gupta authored
[ Upstream commit 4c6fabda ] | CC lib/nmi_backtrace.o | In file included from ../include/linux/kprobes.h:43:0, | from ../lib/nmi_backtrace.c:17: | ../arch/arc/include/asm/kprobes.h:57:13: warning: 'trap_is_kprobe' defined but not used [-Wunused-function] | static void trap_is_kprobe(unsigned long address, struct pt_regs *regs) | ^~~~~~~~~~~~~~ The warning started with 7d134b2c ("kprobes: move kprobe declarations to asm-generic/kprobes.h") which started including <asm/kprobes.h> unconditionally into <linux/kprobes.h> exposing a stub function for !CONFIG_KPROBES to rest of world. Fix that by making the stub a macro Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Jann Horn authored
commit 8404d7a6 upstream. A packed AppArmor policy contains null-terminated tag strings that are read by unpack_nameX(). However, unpack_nameX() uses string functions on them without ensuring that they are actually null-terminated, potentially leading to out-of-bounds accesses. Make sure that the tag string is null-terminated before passing it to strcmp(). Cc: stable@vger.kernel.org Fixes: 736ec752 ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
John Johansen <john.johansen@canonical.com> Signed-off-by:
-
Andrey Smirnov authored
commit 7c7da40d upstream. In the case of compat syscall ioctl numbers for UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD need to be adjusted before being passed on uinput_ioctl_handler() since code built with -m32 will be passing slightly different values. Extend the code already covering UI_SET_PHYS to cover UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD as well. Reported-by:
Pierre-Loup A. Griffais <pgriffais@valvesoftware.com> Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Mike Marciniszyn authored
commit 3230f4a8 upstream. The following warning can happen when a memory shortage occurs during txreq allocation: [10220.939246] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC) [10220.939246] Hardware name: Intel Corporation S2600WT2R/S2600WT2R, BIOS SE5C610.86B.01.01.0018.C4.072020161249 07/20/2016 [10220.939247] cache: mnt_cache, object size: 384, buffer size: 384, default order: 2, min order: 0 [10220.939260] Workqueue: hfi0_0 _hfi1_do_send [hfi1] [10220.939261] node 0: slabs: 1026568, objs: 43115856, free: 0 [10220.939262] Call Trace: [10220.939262] node 1: slabs: 820872, objs: 34476624, free: 0 [10220.939263] dump_stack+0x5a/0x73 [10220.939265] warn_alloc+0x103/0x190 [10220.939267] ? wake_all_kswapds+0x54/0x8b [10220.939268] __alloc_pages_slowpath+0x86c/0xa2e [10220.939270] ? __alloc_pages_nodemask+0x2fe/0x320 [10220.939271] __alloc_pages_nodemask+0x2fe/0x320 [10220.939273] new_slab+0x475/0x550 [10220.939275] ___slab_alloc+0x36c/0x520 [10220.939287] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939299] ? __get_txreq+0x54/0x160 [hfi1] [10220.939310] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939312] __slab_alloc+0x40/0x61 [10220.939323] ? hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939325] kmem_cache_alloc+0x181/0x1b0 [10220.939336] hfi1_make_rc_req+0x90/0x18b0 [hfi1] [10220.939348] ? hfi1_verbs_send_dma+0x386/0xa10 [hfi1] [10220.939359] ? find_prev_entry+0xb0/0xb0 [hfi1] [10220.939371] hfi1_do_send+0x1d9/0x3f0 [hfi1] [10220.939372] process_one_work+0x171/0x380 [10220.939374] worker_thread+0x49/0x3f0 [10220.939375] kthread+0xf8/0x130 [10220.939377] ? max_active_store+0x80/0x80 [10220.939378] ? kthread_bind+0x10/0x10 [10220.939379] ret_from_fork+0x35/0x40 [10220.939381] SLUB: Unable to allocate memory on node -1, gfp=0xa20(GFP_ATOMIC) The shortage is handled properly so the message isn't needed. Silence by adding the no warn option to the slab allocation. Fixes: 45842abb ("staging/rdma/hfi1: move txreq header code") Cc: <stable@vger.kernel.org> Reviewed-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Peter Chen authored
commit c19dffc0 upstream. An endpoint conflict occurs when the USB is working in device mode during an isochronous communication. When the endpointA IN direction is an isochronous IN endpoint, and the host sends an IN token to endpointA on another device, then the OUT transaction may be missed regardless the OUT endpoint number. Generally, this occurs when the device is connected to the host through a hub and other devices are connected to the same hub. The affected OUT endpoint can be either control, bulk, isochronous, or an interrupt endpoint. After the OUT endpoint is primed, if an IN token to the same endpoint number on another device is received, then the OUT endpoint may be unprimed (cannot be detected by software), which causes this endpoint to no longer respond to the host OUT token, and thus, no corresponding interrupt occurs. There is no good workaround for this issue, the only thing the software could do is numbering isochronous IN from the highest endpoint since we have observed most of device number endpoint from the lowest. Cc: <stable@vger.kernel.org> #v3.14+ Cc: Fabio Estevam <festevam@gmail.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Jun Li <jun.li@nxp.com> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Stanley Chu authored
commit 24e2e7a1 upstream. UFS runtime suspend can be triggered after pm_runtime_enable() is invoked in ufshcd_pltfrm_init(). However if the first runtime suspend is triggered before binding ufs_hba structure to ufs device structure via platform_set_drvdata(), then UFS runtime suspend will be no longer triggered in the future because its dev->power.runtime_error was set in the first triggering and does not have any chance to be cleared. To be more clear, dev->power.runtime_error is set if hba is NULL in ufshcd_runtime_suspend() which returns -EINVAL to rpm_callback() where dev->power.runtime_error is set as -EINVAL. In this case, any future rpm_suspend() for UFS device fails because rpm_check_suspend_allowed() fails due to non-zero dev->power.runtime_error. To resolve this issue, make sure the first UFS runtime suspend get valid "hba" in ufshcd_runtime_suspend(): Enable UFS runtime PM only after hba is successfully bound to UFS device structure. Fixes: 62694735 ([SCSI] ufs: Add runtime PM support for UFS host controller driver) Cc: stable@vger.kernel.org Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Linus Torvalds authored
commit 6f303d60 upstream. We already did this for clang, but now gcc has that warning too. Yes, yes, the address may be unaligned. And that's kind of the point. Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Miguel Ojeda authored
commit 0c97bf86 upstream. Starting with GCC 9, -Warray-bounds detects cases when memset is called starting on a member of a struct but the size to be cleared ends up writing over further members. Such a call happens in the trace code to clear, at once, all members after and including `seq` on struct trace_iterator: In function 'memset', inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3: ./include/linux/string.h:344:9: warning: '__builtin_memset' offset [8505, 8560] from the object at 'iter' is out of the bounds of referenced subobject 'seq' with type 'struct trace_seq' at offset 4368 [-Warray-bounds] 344 | return __builtin_memset(p, c, size); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ In order to avoid GCC complaining about it, we compute the address ourselves by adding the offsetof distance instead of referring directly to the member. Since there are two places doing this clear (trace.c and trace_kdb.c), take the chance to move the workaround into a single place in the internal header. Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.comSigned-off-by:
Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> [ Removed unnecessary parenthesis around "iter" ] Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
- 27 Jun, 2019 2 commits
-
-
Greg Kroah-Hartman authored
-
Eric Dumazet authored
commit b6653b36 upstream. tcp_fragment() might be called for skbs in the write queue. Memory limits might have been exceeded because tcp_sendmsg() only checks limits at full skb (64KB) boundaries. Therefore, we need to make sure tcp_fragment() wont punish applications that might have setup very low SO_SNDBUF values. Fixes: f070ef2a ("tcp: tcp_fragment() should apply sane memory limits") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Christoph Paasch <cpaasch@apple.com> Tested-by:
-
- 22 Jun, 2019 19 commits
-
-
Greg Kroah-Hartman authored
-
Alexander Lochmann authored
commit f69e749a upstream. file_remove_privs() might be called for non-regular files, e.g. blkdev inode. There is no reason to do its job on things like blkdev inodes, pipes, or cdevs. Hence, abort if file does not refer to a regular inode. AV: more to the point, for devices there might be any number of inodes refering to given device. Which one to strip the permissions from, even if that made any sense in the first place? All of them will be observed with contents modified, after all. Found by LockDoc (Alexander Lochmann, Horst Schirmeier and Olaf Spinczyk) Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Alexander Lochmann <alexander.lochmann@tu-dortmund.de> Signed-off-by:
Horst Schirmeier <horst.schirmeier@tu-dortmund.de> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by:
-
Amit Cohen authored
[ Upstream commit 275e928f ] Force of 56G is not supported by hardware in Ethernet devices. This configuration fails with a bad parameter error from firmware. Add check of this case. Instead of trying to set 56G with autoneg off, return a meaningful error. Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC") Signed-off-by:
Amit Cohen <amitc@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Jason Yan authored
[ Upstream commit 3b054179 ] The sas_port(phy->port) allocated in sas_ex_discover_expander() will not be deleted when the expander failed to discover. This will cause resource leak and a further issue of kernel BUG like below: [159785.843156] port-2:17:29: trying to add phy phy-2:17:29 fails: it's already part of another port [159785.852144] ------------[ cut here ]------------ [159785.856833] kernel BUG at drivers/scsi/scsi_transport_sas.c:1086! [159785.863000] Internal error: Oops - BUG: 0 [#1] SMP [159785.867866] CPU: 39 PID: 16993 Comm: kworker/u96:2 Tainted: G W OE 4.19.25-vhulk1901.1.0.h111.aarch64 #1 [159785.878458] Hardware name: Huawei Technologies Co., Ltd. Hi1620EVBCS/Hi1620EVBCS, BIOS Hi1620 CS B070 1P TA 03/21/2019 [159785.889231] Workqueue: 0000:74:02.0_disco_q sas_discover_domain [159785.895224] pstate: 40c00009 (nZcv daif +PAN +UAO) [159785.900094] pc : sas_port_add_phy+0x188/0x1b8 [159785.904524] lr : sas_port_add_phy+0x188/0x1b8 [159785.908952] sp : ffff0001120e3b80 [159785.912341] x29: ffff0001120e3b80 x28: 0000000000000000 [159785.917727] x27: ffff802ade8f5400 x26: ffff0000681b7560 [159785.923111] x25: ffff802adf11a800 x24: ffff0000680e8000 [159785.928496] x23: ffff802ade8f5728 x22: ffff802ade8f5708 [159785.933880] x21: ffff802adea2db40 x20: ffff802ade8f5400 [159785.939264] x19: ffff802adea2d800 x18: 0000000000000010 [159785.944649] x17: 00000000821bf734 x16: ffff00006714faa0 [159785.950033] x15: ffff0000e8ab4ecf x14: 7261702079646165 [159785.955417] x13: 726c612073277469 x12: ffff00006887b830 [159785.960802] x11: ffff00006773eaa0 x10: 7968702079687020 [159785.966186] x9 : 0000000000002453 x8 : 726f702072656874 [159785.971570] x7 : 6f6e6120666f2074 x6 : ffff802bcfb21290 [159785.976955] x5 : ffff802bcfb21290 x4 : 0000000000000000 [159785.982339] x3 : ffff802bcfb298c8 x2 : 337752b234c2ab00 [159785.987723] x1 : 337752b234c2ab00 x0 : 0000000000000000 [159785.993108] Process kworker/u96:2 (pid: 16993, stack limit = 0x0000000072dae094) [159786.000576] Call trace: [159786.003097] sas_port_add_phy+0x188/0x1b8 [159786.007179] sas_ex_get_linkrate.isra.5+0x134/0x140 [159786.012130] sas_ex_discover_expander+0x128/0x408 [159786.016906] sas_ex_discover_dev+0x218/0x4c8 [159786.021249] sas_ex_discover_devices+0x9c/0x1a8 [159786.025852] sas_discover_root_expander+0x134/0x160 [159786.030802] sas_discover_domain+0x1b8/0x1e8 [159786.035148] process_one_work+0x1b4/0x3f8 [159786.039230] worker_thread+0x54/0x470 [159786.042967] kthread+0x134/0x138 [159786.046269] ret_from_fork+0x10/0x18 [159786.049918] Code: 91322300 f0004402 91178042 97fe4c9b (d4210000) [159786.056083] Modules linked in: hns3_enet_ut(OE) hclge(OE) hnae3(OE) hisi_sas_test_hw(OE) hisi_sas_test_main(OE) serdes(OE) [159786.067202] ---[ end trace 03622b9e2d99e196 ]--- [159786.071893] Kernel panic - not syncing: Fatal exception [159786.077190] SMP: stopping secondary CPUs [159786.081192] Kernel Offset: disabled [159786.084753] CPU features: 0x2,a2a00a38 Fixes: 2908d778 ("[SCSI] aic94xx: new driver") Reported-by:
Jian Luo <luojian5@huawei.com> Signed-off-by:
Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> Signed-off-by:
-
Lianbo Jiang authored
[ Upstream commit 1d94f06e ] When SME is enabled, the smartpqi driver won't work on the HP DL385 G10 machine, which causes the failure of kernel boot because it fails to allocate pqi error buffer. Please refer to the kernel log: .... [ 9.431749] usbcore: registered new interface driver uas [ 9.441524] Microsemi PQI Driver (v1.1.4-130) [ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5 [ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found Starting dracut initqueue hook... [ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1 en. [ OK ] Started Forward Password Requests to Plymouth Directory Watch. [[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer .... [ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts [ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts Basically, the fact that the coherent DMA mask value wasn't set caused the driver to fall back to SWIOTLB when SME is active. For correct operation, lets call the dma_set_mask_and_coherent() to properly set the mask for both streaming and coherent, in order to inform the kernel about the devices DMA addressing capabilities. Signed-off-by:
Lianbo Jiang <lijiang@redhat.com> Acked-by:
Don Brace <don.brace@microsemi.com> Tested-by:
-
Varun Prakash authored
[ Upstream commit cc555759 ] ip_dev_find() can return NULL so add a check for NULL pointer. Signed-off-by:
Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Yoshihiro Shimoda authored
[ Upstream commit 315ca92d ] The sh_eth_close() resets the MAC and then calls phy_stop() so that mdio read access result is incorrect without any error according to kernel trace like below: ifconfig-216 [003] .n.. 109.133124: mdio_access: ee700000.ethernet-ffffffff read phy:0x01 reg:0x00 val:0xffff According to the hardware manual, the RMII mode should be set to 1 before operation the Ethernet MAC. However, the previous code was not set to 1 after the driver issued the soft_reset in sh_eth_dev_exit() so that the mdio read access result seemed incorrect. To fix the issue, this patch adds a condition and set the RMII mode register in sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs. Note that when I have tried to move the sh_eth_dev_exit() calling after phy_stop() on sh_eth_close(), but it gets worse (kernel panic happened and it seems that a register is accessed while the clock is off). Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 5a3f4936 ] Currently the HV KVM code takes the kvm->lock around calls to kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call kvm_for_each_vcpu() internally). However, that leads to a lock order inversion problem, because these are called in contexts where the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock according to Documentation/virtual/kvm/locking.txt. Hence there is a possibility of deadlock. To fix this, we simply don't take the kvm->lock mutex around these calls. This is safe because the implementations of kvm_for_each_vcpu() and kvm_get_vcpu_by_id() have been designed to be able to be called locklessly. Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Reviewed-by:
Cédric Le Goater <clg@kaod.org> Signed-off-by:
-
Paul Mackerras authored
[ Upstream commit 1659e27d ] Currently the Book 3S KVM code uses kvm->lock to synchronize access to the kvm->arch.rtas_tokens list. Because this list is scanned inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held, taking kvm->lock cause a lock inversion problem, which could lead to a deadlock. To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests inside the vcpu mutexes, and use that instead of kvm->lock when accessing the rtas token list. This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free(). At this point we don't hold the new mutex, but that is OK because kvmppc_rtas_tokens_free() is only called when the whole VM is being destroyed, and at that point nothing can be looking up a token in the list. Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit 9a626c4a ] Fix build errors on ia64 when DISCONTIGMEM=y and NUMA=y by exporting paddr_to_nid(). Fixes these build errors: ERROR: "paddr_to_nid" [sound/core/snd-pcm.ko] undefined! ERROR: "paddr_to_nid" [net/sunrpc/sunrpc.ko] undefined! ERROR: "paddr_to_nid" [fs/cifs/cifs.ko] undefined! ERROR: "paddr_to_nid" [drivers/video/fbdev/core/fb.ko] undefined! ERROR: "paddr_to_nid" [drivers/usb/mon/usbmon.ko] undefined! ERROR: "paddr_to_nid" [drivers/usb/core/usbcore.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/raid1.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-mod.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-crypt.ko] undefined! ERROR: "paddr_to_nid" [drivers/md/dm-bufio.ko] undefined! ERROR: "paddr_to_nid" [drivers/ide/ide-core.ko] undefined! ERROR: "paddr_to_nid" [drivers/ide/ide-cd_mod.ko] undefined! ERROR: "paddr_to_nid" [drivers/gpu/drm/drm.ko] undefined! ERROR: "paddr_to_nid" [drivers/char/agp/agpgart.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/nbd.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/loop.ko] undefined! ERROR: "paddr_to_nid" [drivers/block/brd.ko] undefined! ERROR: "paddr_to_nid" [crypto/ccm.ko] undefined! Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: linux-ia64@vger.kernel.org Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
-
Thomas Richter authored
[ Upstream commit 6738028d ] Command 'perf record' and 'perf report' on a system without kernel debuginfo packages uses /proc/kallsyms and /proc/modules to find addresses for kernel and module symbols. On x86 this works for root and non-root users. On s390, when invoked as non-root user, many of the following warnings are shown and module symbols are missing: proc/{kallsyms,modules} inconsistency while looking for "[sha1_s390]" module! Command 'perf record' creates a list of module start addresses by parsing the output of /proc/modules and creates a PERF_RECORD_MMAP record for the kernel and each module. The following function call sequence is executed: machine__create_kernel_maps machine__create_module modules__parse machine__create_module --> for each line in /proc/modules arch__fix_module_text_start Function arch__fix_module_text_start() is s390 specific. It opens file /sys/module/<name>/sections/.text to extract the module's .text section start address. On s390 the module loader prepends a header before the first section, whereas on x86 the module's text section address is identical the the module's load address. However module section files are root readable only. For non-root the read operation fails and machine__create_module() returns an error. Command perf record does not generate any PERF_RECORD_MMAP record for loaded modules. Later command perf report complains about missing module maps. To fix this function arch__fix_module_text_start() always returns success. For root users there is no change, for non-root users the module's load address is used as module's text start address (the prepended header then counts as part of the text section). This enable non-root users to use module symbols and avoid the warning when perf report is executed. Output before: [tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP 0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text Output after: [tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP 0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text 0 0x1b8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../autofs4.ko.xz 0 0x250 [0xa8]: PERF_RECORD_MMAP ... x /lib/modules/.../sha_common.ko.xz 0 0x2f8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../des_generic.ko.xz Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Reviewed-by:
Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Link: http://lkml.kernel.org/r/20190522144601.50763-4-tmricht@linux.ibm.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Shawn Landden authored
[ Upstream commit 97acec7d ] This strncat() is safe because the buffer was allocated with zalloc(), however gcc doesn't know that. Since the string always has 4 non-null bytes, just use memcpy() here. CC /home/shawn/linux/tools/perf/util/data-convert-bt.o In file included from /usr/include/string.h:494, from /home/shawn/linux/tools/lib/traceevent/event-parse.h:27, from util/data-convert-bt.c:22: In function ‘strncat’, inlined from ‘string_set_value’ at util/data-convert-bt.c:274:4: /usr/include/powerpc64le-linux-gnu/bits/string_fortified.h:136:10: error: ‘__builtin_strncat’ output may be truncated copying 4 bytes from a string of length 4 [-Werror=stringop-truncation] 136 | return __builtin___strncat_chk (__dest, __src, __len, __bos (__dest)); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by:
Shawn Landden <shawn@git.icu> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> LPU-Reference: 20190518183238.10954-1-shawn@git.icu Link: https://lkml.kernel.org/n/tip-289f1jice17ta7tr3tstm9jm@git.kernel.orgSigned-off-by:
-
Sahitya Tummala authored
[ Upstream commit f6122ed2 ] In the vfs_statx() context, during path lookup, the dentry gets added to sd->s_dentry via configfs_attach_attr(). In the end, vfs_statx() kills the dentry by calling path_put(), which invokes configfs_d_iput(). Ideally, this dentry must be removed from sd->s_dentry but it doesn't if the sd->s_count >= 3. As a result, sd->s_dentry is holding reference to a stale dentry pointer whose memory is already freed up. This results in use-after-free issue, when this stale sd->s_dentry is accessed later in configfs_readdir() path. This issue can be easily reproduced, by running the LTP test case - sh fs_racer_file_list.sh /config (https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/fs/racer/fs_racer_file_list.sh) Fixes: 76ae281f ('configfs: fix race between dentry put and lookup') Signed-off-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Yingjoe Chen authored
[ Upstream commit a0692f0e ] If I2C_M_RECV_LEN check failed, msgs[i].buf allocated by memdup_user will not be freed. Pump index up so it will be freed. Fixes: 838bfa60 ("i2c-dev: Add support for I2C_M_RECV_LEN") Signed-off-by:
Yingjoe Chen <yingjoe.chen@mediatek.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Kees Cook authored
[ Upstream commit 3e66b7cc ] Building with Clang reports the redundant use of MODULE_DEVICE_TABLE(): drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table' MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:90:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids); ^ ./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE' extern typeof(name) __mod_##type##__##name##_device_table \ ^ <scratch space>:85:1: note: expanded from here __mod_eisa__de4x5_eisa_ids_device_table ^ This drops the one further from the table definition to match the common use of MODULE_DEVICE_TABLE(). Fixes: 07563c71 ("EISA bus MODALIAS attributes support") Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit e9646f0f ] The gpio-adp5588 driver uses interfaces that are provided by GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry. Fixes these build errors: ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’: ../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’ dev->gpio_chip.irq.domain, gpio)); ^ ../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’: ../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration] ret = gpiochip_irqchip_add_nested(&dev->gpio_chip, ^ ../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration] gpiochip_set_nested_irqchip(&dev->gpio_chip, ^ Fixes: 459773ae ("gpio: adp5588-gpio: support interrupt controller") Reported-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 3f9fbe9b ] Similar to how decrementing rb->next too early can cause data_head to (temporarily) be observed to go backward, so too can this happen when we increment too late. This barrier() ensures the rb->head load happens after the increment, both the one in the 'goto again' path, as the one from perf_output_get_handle() -- albeit very unlikely to matter for the latter. Suggested-by:
Yabin Cui <yabinc@google.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: mark.rutland@arm.com Cc: namhyung@kernel.org Fixes: ef60777c ("perf: Optimize the perf_output() path by removing IRQ-disables") Link: http://lkml.kernel.org/r/20190517115418.309516009@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Yabin Cui authored
[ Upstream commit 1b038c6e ] In perf_output_put_handle(), an IRQ/NMI can happen in below location and write records to the same ring buffer: ... local_dec_and_test(&rb->nest) ... <-- an IRQ/NMI can happen here rb->user_page->data_head = head; ... In this case, a value A is written to data_head in the IRQ, then a value B is written to data_head after the IRQ. And A > B. As a result, data_head is temporarily decreased from A to B. And a reader may see data_head < data_tail if it read the buffer frequently enough, which creates unexpected behaviors. This can be fixed by moving dec(&rb->nest) to after updating data_head, which prevents the IRQ/NMI above from updating data_head. [ Split up by peterz. ] Signed-off-by:
-
Frank van der Linden authored
[ Upstream commit 2ac44ab6 ] For F17h AMD CPUs, the CPB capability ('Core Performance Boost') is forcibly set, because some versions of that chip incorrectly report that they do not have it. However, a hypervisor may filter out the CPB capability, for good reasons. For example, KVM currently does not emulate setting the CPB bit in MSR_K7_HWCR, and unchecked MSR access errors will be thrown when trying to set it as a guest: unchecked MSR access error: WRMSR to 0xc0010015 (tried to write 0x0000000001000011) at rIP: 0xffffffff890638f4 (native_write_msr+0x4/0x20) Call Trace: boost_set_msr+0x50/0x80 [acpi_cpufreq] cpuhp_invoke_callback+0x86/0x560 sort_range+0x20/0x20 cpuhp_thread_fun+0xb0/0x110 smpboot_thread_fn+0xef/0x160 kthread+0x113/0x130 kthread_create_worker_on_cpu+0x70/0x70 ret_from_fork+0x35/0x40 To avoid this issue, don't forcibly set the CPB capability for a CPU when running under a hypervisor. Signed-off-by:
Frank van der Linden <fllinden@amazon.com> Acked-by:
Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: jiaxun.yang@flygoat.com Fixes: 02371991 ("x86/CPU/AMD: Set the CPB bit unconditionally on F17h") Link: http://lkml.kernel.org/r/20190522221745.GA15789@dev-dsk-fllinden-2c-c1893d73.us-west-2.amazon.com [ Minor edits to the changelog. ] Signed-off-by:
-
