The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
	idVendor	0x0572
	idProduct	0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.

USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.

If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.

The hub thread will notice the connect change and resume the bus,
moving the port back to U0

This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted

Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().

Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

For now only 5 small fixes. Most importantly, we have a fix for the TRB
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.

* tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
  Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
  usb: dwc2: pci: Fix an error code in probe
  usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
  usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
  usb: dwc3: core: Clean up ULPI device

When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.

Fixes: c6267a51 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit b4194da3f9087dd38d91b40f9bec42d59ce589a8
since it causes list corruption followed by kernel panic:

Workqueue: adb ffs_aio_cancel_worker
RIP: 0010:__list_add_valid+0x4d/0x70
Call Trace:
insert_work+0x47/0xb0
__queue_work+0xf6/0x400
queue_work_on+0x65/0x70
dwc3_gadget_giveback+0x44/0x50 [dwc3]
dwc3_gadget_ep_dequeue+0x83/0x2d0 [dwc3]
? finish_wait+0x80/0x80
usb_ep_dequeue+0x1e/0x90
process_one_work+0x18c/0x3b0
worker_thread+0x3c/0x390
? process_one_work+0x3b0/0x3b0
kthread+0x11e/0x140
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x3a/0x50

This issue is seen with warm reboot stability testing.
Signed-off-by: Shen Jing <jingx.shen@intel.com>
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We added some error handling to this function but forgot to set the
error code on this path.

Fixes: ecd29dab ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.

Fixes: 5741022c ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.

Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.

Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().

Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.

Verified on Sunrise Point-LP and Cannon Lake.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.

Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.

Restrict the USB2 resume status check in USB2 roothub to fix hang issue.

Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.

Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.

[1] ade2e3a1 xhci: handle transfer events without TRB pointer

Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing  NULL pointer dereference.

Check if xhci->shared_hcd is still valid before handing USB3 port events

Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()

The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)

Afer commit fe190ed0 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.

shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.

xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087 ("usb: xhci: plat: Create both
HCDs before adding them")

Fixes: fe190ed0 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-toolsSigned-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[  206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[  206.143691] usb 3-2.4: device descriptor read/64, error -32
[  206.351671] usb 3-2.4: device descriptor read/64, error -32

Info for this hub:
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev=01.11
S:  Product=USB 2.0 Hub
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.

Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.

To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.

Fixes: c6267a51 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with

sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'

To avoid this failure, clean up ULPI device.

Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation

With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.

Fixed: 051f3ca0 ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes who have come in near or during the merge window:

   - Removal of a VLA usage in Marvell mpp platform code

   - Enable some IPMI options for ARM64 servers by default, helps
     testing

   - Enable PREEMPT on 32-bit ARMv7 defconfig

   - Minor fix for stm32 DT (removal of an unused DMA property)

   - Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
  ARM: orion: avoid VLA in orion_mpp_conf
  ARM: defconfig: Update multi_v7 to use PREEMPT
  arm64: defconfig: Enable some IPMI configs
  soc: ti: QMSS: Fix usage of irq_set_affinity_hint
  ARM: OMAP1: ams-delta: Fix impossible .irq < 0

Pull more arm64 updates from Catalin Marinas:

 - fix W+X page (mark RO) allocated by the arm64 kprobes code

 - Makefile fix for .i files in out of tree modules

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kprobe: make page to RO mode when allocate it
  arm64: kdump: fix small typo
  arm64: makefile fix build of .i file in external module case

Pull dma-mapping fix from Christoph Hellwig:
 "Avoid compile warnings on non-default arm64 configs"

* tag 'dma-mapping-4.20-2' of git://git.infradead.org/users/hch/dma-mapping:
  arm64: fix warnings without CONFIG_IOMMU_DMA

Pull Kbuild updates from Masahiro Yamada:

 - clean-up leftovers in Kconfig files

 - remove stale oldnoconfig and silentoldconfig targets

 - remove unneeded cc-fullversion and cc-name variables

 - improve merge_config script to allow overriding option prefix

* tag 'kbuild-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: remove cc-name variable
  kbuild: replace cc-name test with CONFIG_CC_IS_CLANG
  merge_config.sh: Allow to define config prefix
  kbuild: remove unused cc-fullversion variable
  kconfig: remove silentoldconfig target
  kconfig: remove oldnoconfig target
  powerpc: PCI_MSI needs PCI
  powerpc: remove CONFIG_MCA leftovers
  powerpc: remove CONFIG_PCI_QSPAN
  scsi: aha152x: rename the PCMCIA define

Pull cifs fixes and updates from Steve French:
 "Three small fixes (one Kerberos related, one for stable, and another
  fixes an oops in xfstest 377), two helpful debugging improvements,
  three patches for cifs directio and some minor cleanup"

* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix signed/unsigned mismatch on aio_read patch
  cifs: don't dereference smb_file_target before null check
  CIFS: Add direct I/O functions to file_operations
  CIFS: Add support for direct I/O write
  CIFS: Add support for direct I/O read
  smb3: missing defines and structs for reparse point handling
  smb3: allow more detailed protocol info on open files for debugging
  smb3: on kerberos mount if server doesn't specify auth type use krb5
  smb3: add trace point for tree connection
  cifs: fix spelling mistake, EACCESS -> EACCES
  cifs: fix return value for cifs_listxattr

Pull 9p fix from Al Viro:
 "Regression fix for net/9p handling of iov_iter; broken by braino when
  switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"

* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  iov_iter: Fix 9p virtio breakage

Pull more SCSI updates from James Bottomley:
 "This is a set of minor small (and safe changes) that didn't make the
  initial pull request plus some bug fixes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mvsas: Remove set but not used variable 'id'
  scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
  scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
  scsi: qla2xxx: Remove a set-but-not-used variable
  scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
  scsi: qla2xxx: Declare local functions 'static'
  scsi: qla2xxx: Improve several kernel-doc headers
  scsi: qla2xxx: Modify fall-through annotations
  scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
  scsi: mvsas: Use dma_pool_zalloc
  scsi: target: Don't request modules that aren't even built
  scsi: target: Set response length for REPORT TARGET PORT GROUPS

Merge more updates from Andrew Morton:

 - more ocfs2 work

 - various leftovers

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  memory_hotplug: cond_resched in __remove_pages
  bfs: add sanity check at bfs_fill_super()
  kernel/sysctl.c: remove duplicated include
  kernel/kexec_file.c: remove some duplicated includes
  mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
  ocfs2: fix clusters leak in ocfs2_defrag_extent()
  ocfs2: dlmglue: clean up timestamp handling
  ocfs2: don't put and assigning null to bh allocated outside
  ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
  ocfs2: don't use iocb when EIOCBQUEUED returns
  ocfs2: without quota support, avoid calling quota recovery
  ocfs2: remove ocfs2_is_o2cb_active()
  mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
  include/linux/notifier.h: SRCU: fix ctags
  mm: handle no memcg case in memcg_kmem_charge() properly

We have received a bug report that unbinding a large pmem (>1TB) can
result in a soft lockup:

  NMI watchdog: BUG: soft lockup - CPU#9 stuck for 23s! [ndctl:4365]
  [...]
  Supported: Yes
  CPU: 9 PID: 4365 Comm: ndctl Not tainted 4.12.14-94.40-default #1 SLE12-SP4
  Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.01.00.0833.051120182255 05/11/2018
  task: ffff9cce7d4410c0 task.stack: ffffbe9eb1bc4000
  RIP: 0010:__put_page+0x62/0x80
  Call Trace:
   devm_memremap_pages_release+0x152/0x260
   release_nodes+0x18d/0x1d0
   device_release_driver_internal+0x160/0x210
   unbind_store+0xb3/0xe0
   kernfs_fop_write+0x102/0x180
   __vfs_write+0x26/0x150
   vfs_write+0xad/0x1a0
   SyS_write+0x42/0x90
   do_syscall_64+0x74/0x150
   entry_SYSCALL_64_after_hwframe+0x3d/0xa2
  RIP: 0033:0x7fd13166b3d0

It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large.  Fix the issue by calling
cond_resched once per memory section.

Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>