- 23 Jan, 2022 40 commits
-
-
Yunfei Dong authored
Use the dma_set_mask_and_coherent helper to set vdec DMA bit mask to support 34bits iova space(16GB) that the mt8192 iommu HW support. Whole the iova range separate to 0~4G/4G~8G/8G~12G/12G~16G, regarding which iova range VDEC actually locate, it depends on the dma-ranges property of vdec dtsi node. Signed-off-by:
Yunfei Dong <yunfei.dong@mediatek.com> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab@kernel.org>
-
Yunfei Dong authored
Add work queue to process core hardware information. First, get lat_buf from message queue, then call core hardware of each codec(H264/VP9/AV1) to decode, finally puts lat_buf back to the message. Signed-off-by:
Steve Cho <stevecho@chromium.org> Signed-off-by:
-
Yunfei Dong authored
For add new hardware, not only need to lock lat hardware, also need to lock core hardware in case of different instance start to decoder at the same time. Signed-off-by:
-
Yunfei Dong authored
Generalizes power and clock on/off interfaces to support different hardware. Signed-off-by:
-
Yunfei Dong authored
For lat and core architecture, lat thread will send message to core thread when lat decode done. Core hardware will use the message from lat to decode, then free message to lat thread when decode done. Signed-off-by:
-
Yunfei Dong authored
Adds irq interface for multi hardware. Signed-off-by:
-
Yunfei Dong authored
Separates different architecture for hardware: pure_sin_core and lat_sin_core. MT8183 is pure single core. Uses .hw_arch to distinguish. Signed-off-by:
-
Yunfei Dong authored
There are more than two hardwares for decoder: LAT0, LAT1 and CORE. In order to manage these hardwares, register each hardware as independent platform device for the larbs are different. Each hardware module controls its own information which includes interrupt/power/clocks/registers. Calling of_platform_populate in parent device, and use subdev_bitmap to record whether the hardwares are registered. Signed-off-by:
-
Yunfei Dong authored
Adds MT8192's compatible "mediatek,mt8192-vcodec-dec". Adds MT8192's device private data mtk_lat_sig_core_pdata. Signed-off-by:
-
Yunfei Dong authored
Adds decoder dt-bindings for mt8192. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Yunfei Dong authored
Separate decoder and encoder document for the dts are big difference. Signed-off-by:
-
Yunfei Dong authored
When mtk vcodec decoder is build as a module, we need to export mtk-vcodec-dec pm functions to make them visible by the other components. Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@collabora.com> Signed-off-by:
-
Yunfei Dong authored
Using the needed params for pm init/release function and remove unused param mtkdev in 'struct mtk_vcodec_pm'. Signed-off-by:
Tzung-Bi Shih <tzungbi@google.com> Reviewed-by:
-
Yunfei Dong authored
Vdec and venc can use the same function to wake up interrupt event. Signed-off-by:
-
Yunfei Dong authored
Different platforms may have different numbers of register bases. Gets the numbers of register bases from dts (sizeof(u32) * 4 bytes for each). Signed-off-by:
-
Benjamin Gaignard authored
Reference Picture Set lists provide indices of short and long term reference in DBP array. Fix Hantro to not do a look up in DBP entries. Make documentation more clear about it. [hverkuil: fix typo in commit log] Signed-off-by:
Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by:
-
Benjamin Gaignard authored
Marking a picture as long-term reference is valid for DPB but not for RPS. Change flag name to match with the description in HEVC spec chapter "8.3.2 Decoding process for reference picture set". PocStCurrBefore, PocStCurrAfter, PocLtCurr lists could be built by the kernel from the DPB entries struct v4l2_hevc_dpb_entry, using the information in the rps field. This way RPS flags becomes useless and are removed. This patch breaks the staging HEVC API because it introduces a new flag, changes a field name in v4l2_hevc_dpb_entry structure and removes V4L2_HEVC_DPB_ENTRY_RPS_* flags. [hverkuil: fixed some typos] Signed-off-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by:
-
Eugen Hristev authored
The ISC can dump the 8 bit and 10 bit raw bayer formats directly to the memory. Thus, add them to the supported output format list. Signed-off-by:
Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by:
-
Eugen Hristev authored
Fix the mbus code for UYVY input format type to the right color rotation. Signed-off-by:
-
Eugen Hristev authored
White balance computed gains can overflow above the 13 bits hardware coefficient that can be used, in some specific scenarios like a subexposure from the sensor when the image is mostly black. In this case the computed gain has to be clamped to the maximum value allowed by the hardware. Signed-off-by:
-
Eugen Hristev authored
Add debug messages that make it easier to debug white balance algorithm. Signed-off-by:
-
Eugen Hristev authored
The bytesperline field of the pixfmt should be only for the first plane in case of planar formats like YUV420 or YUV422. The bytesperline is used by the driver to compute the framesize. We have to report a different bpp (bytes per pixel) to v4l2 in bytesperline than the actual bpp. For example for YUV420, the real bpp is 12, but the first plane has only 8 bpp. Thus we report a bytesperline 8*width instead of 12*width. However, for real framezise we have to compute 12*width*height. Hence added a new variable to hold this information and to correctly compute the frame size. Signed-off-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Eugen Hristev authored
The ISC supports a full broad range of frame sizes. Until now, the subdevice was queried for possible frame sizes and these were reported to the user space. However, the ISC should not care about which frame sizes the subdev supports, as long as this frame size is supported. Thus, report a continuous range from smallest frame size up to the max resolution. Signed-off-by:
-
Eugen Hristev authored
VIDIOC_ENUM_FRAMEINTERVALS is not recommended for a top video driver. The frame rate is defined by the sensor subdevice, thus it can be queried directly by anyone interested in the frame intervals. Signed-off-by:
-
Eugen Hristev authored
The ispck is not used for sama7g5 variant of the ISC. Calls to ispck have to be removed also from module insert/removal. Fixes: d7f26849 ("media: atmel: fix the ispck initialization") Signed-off-by:
-
Eugen Hristev authored
To have consistency with future media controller development, replace the video device name with KBUILD_MODNAME. Signed-off-by:
-
Eugen Hristev authored
The atmel-isc-base is getting crowded. Split the clock functions into atmel-isc-clk.c. Signed-off-by:
-
Eugen Hristev authored
Microchip CSI2DC (CSI2 Demultiplexer Controller) is a misc bridge device that converts a byte stream in IDI Synopsys format (coming from a CSI2HOST) to a pixel stream that can be captured by a sensor controller. Signed-off-by:
-
Eugen Hristev authored
Add bindings documentation for Microchip CSI2 Demultiplexer controller. CSI2DC is a demultiplexer from Synopsys IDI interface specification to parallel interface connection or direct memory access. CSI2DC can also act as a parallel bypass from a parallel sensor to the image sensor controller/interface. Signed-off-by:
-
Eugen Hristev authored
Add Microchip CSI2DC driver in the list. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Alain Volmat authored
Prior to submitting a transfer to the DMA, the client should first check the capabilities of the DMA channel in term of maximum of each segment. This is given by the max_sg_burst value reported by dma_get_slave_caps API. Based on that, if the transfer is larger than what can be handled by the DMA channel, we split the transfer into several scatterlist elements. [hverkuil: fix checkpatch parenthesis alignment warning] Signed-off-by:
Alain Volmat <alain.volmat@foss.st.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array range on the stack but instead it static. Also makes the object code a little smaller. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array probe_ports on the stack but instead it static const. Also makes the object code a little smaller. Signed-off-by:
-
Colin Ian King authored
Don't populate the read-only array regs_to_read on the stack but instead it static const. Also makes the object code a little smaller. Signed-off-by:
-
Ondrej Zary authored
Commit 21615365 ("media: media/pci: set device_caps in struct video_device") introduced a regression: V4L2_CAP_TUNER is always present in device_caps, even when the device has no tuner. This causes a warning: WARNING: CPU: 0 PID: 249 at drivers/media/v4l2-core/v4l2-ioctl.c:1102 v4l_querycap+0xa0/0xb0 [videodev] Fixes: 21615365 ("media: media/pci: set device_caps in struct video_device") Signed-off-by:
Ondrej Zary <linux@zary.sk> Signed-off-by:
-
Ming Qian authored
V4L2_PIX_FMT_NV12 requires num_planes equals to 1, V4L2_PIX_FMT_NV12M requires num_planes equals to 2. and mxc-jpeg supports 2 planes for nv12, so we should use 4L2_PIX_FMT_NV12M instead of V4L2_PIX_FMT_NV12, otherwise it will confuses gstreamer and prevent encoding and decoding. Signed-off-by:
Ming Qian <ming.qian@nxp.com> Signed-off-by:
Shijie Qin <shijie.qin@nxp.com> Signed-off-by:
Zhou Peng <eagle.zhou@nxp.com> Reviewed-by:
Mirela Rabulea <mirela.rabulea@oss.nxp.com> Signed-off-by:
-
Johan Hovold authored
Drivers should generally not print anything for a successful probe, and printing "success" before probe is done makes no sense. Drop the unnecessary and misleading dev_info() call from probe. Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Lad Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Johan Hovold authored
The driver allocates and registers two platform device structures during probe, but the devices were never deregistered on driver unbind. This results in a use-after-free on driver unbind as the device structures were allocated using devres and would be freed by driver core when remove() returns. Fix this by adding the missing deregistration calls to the remove() callback and failing probe on registration errors. Note that the platform device structures must be freed using a proper release callback to avoid leaking associated resources like device names. Fixes: 479f7a11 ("[media] davinci: vpif: adaptions for DT support") Cc: stable@vger.kernel.org # 4.12 Cc: Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Johan Hovold authored
Make sure to disable runtime PM before returning on probe errors. Fixes: 479f7a11 ("[media] davinci: vpif: adaptions for DT support") Cc: stable@vger.kernel.org Cc: Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
Johan Hovold authored
Make sure to balance the runtime PM usage counter on driver unbind. Fixes: 407ccc65 ("[media] davinci: vpif: add pm_runtime support") Cc: stable@vger.kernel.org # 3.9 Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
