- 14 May, 2012 40 commits
-
-
Sylwester Nawrocki authored
This patch adds definition of additional color effects: - V4L2_COLORFX_AQUA, - V4L2_COLORFX_ART_FREEZE, - V4L2_COLORFX_SILHOUETTE, - V4L2_COLORFX_SOLARIZATION, - V4L2_COLORFX_ANTIQUE, - V4L2_COLORFX_SET_CBCR. The new V4L2_COLORFX_CBCR control is added to allow setting the fixed Cb, Cr values that replace chroma Cb/Cr coefficients in case of V4L2_COLORFX_SET_CBCR effect. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
The radio-si470x-usb driver supported both autosuspend and it stopped the radio the moment the last user of the radio device closed it. However, that was very confusing since if you play the audio from the device (e.g. through arecord -D ... | aplay) then no sound would play unless you had the radio device open at the same time, even though there is no need to do anything with that node. On the other hand, the actual suspend/resume functions didn't do anything, which would fail if you *did* have the radio node open at that time. So: - remove autosuspend (bad idea in general for USB radio devices) - move the start/stop out of the open/release functions into the resume/suspend functions. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Tobias Lorenz <tobias.lorenz@gmx.net> Signed-off-by:
-
Hans Verkuil authored
There is no need to report an error in the log, you are already returning that error to userspace after all. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
This cleans up the code and si470x now uses the proper v4l2 frameworks and passes most of the v4l2-compliance tests. Signed-off-by:
-
Laurent Pinchart authored
This fixes the following warning: In file included from drivers/media/video/v4l2-subdev.c:29: include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside parameter list include/media/v4l2-ctrls.h:501: warning: its scope is only this definition or declaration, which is probably not what you want include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside parameter list Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
-
Kartik Mohta authored
The driver uses the ctrl value passed in as a bool to determine whether to enable auto-exposure, but the auto-exposure setting is defined as an enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads to a reversed logic where if you send in AUTO, it actually sets manual exposure and vice-versa. Signed-off-by:
Kartik Mohta <kartikmohta@gmail.com> Signed-off-by:
-
Guennadi Liakhovetski authored
Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
Fix the following compilation failure: linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop': linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop' linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format': linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format' linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe': linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity' linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity' linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove': linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity' make[4]: *** [drivers/media/video/mt9m032.o] Error 1 by adding a dependency on VIDEO_V4L2_SUBDEV_API. Signed-off-by:
-
Guennadi Liakhovetski authored
Fix a copy-paste typo and a nested locking function call in mt9m032. Signed-off-by:
-
Laurent Pinchart authored
Add four new controls to configure black level compensation (BLC): - V4L2_CID_BLC_AUTO selects between manual and auto BLC - V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC - V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC - V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC Signed-off-by:
-
Laurent Pinchart authored
Use the GPIO from the sensor driver instead of calling back to board code. Signed-off-by:
-
Laurent Pinchart authored
Instead of passing a color/monochrome flag through platform data, rely on the I2C device name to identify the chip model. Signed-off-by:
-
Antti Palosaari authored
Add all known reference design USB IDs. Rename two earlier reference design USB IDs. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
We can use tuner ID instead of HW not supported flag. Lesser code is better code. Signed-off-by:
-
Antti Palosaari authored
Fixes most problems when having more than one device connected as demod and tuner configurations are not shared. Signed-off-by:
-
Hans-Frieder Vogt authored
af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt: - bit_cnt is always 0x2710 (10000) - abort_cnt is between 0 and 0x2710 - err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8) in the current implementation BER is calculated as the number of bit errors per processed bits, ignoring those bits that are already discarded and counted in abort_cnt, i.e. UCBLOCKS. Signed-off-by:
Hans-Frieder Vogt <hfvogt@gmx.net> Signed-off-by:
-
Hans-Frieder Vogt authored
Signed-off-by:
-
Antti Palosaari authored
Not used anymore since new firmware downloader. I forget to remove those earlier when changed firmware downloader. Signed-off-by:
-
Antti Palosaari authored
Fix USB buffer len to maximum possible. Various log writing fixes, remove extra new lines and excessive type casts. Rename and type change some variables. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Sylwester Nawrocki authored
When setting TRY crop on the sub-device the mutex was erroneously acquired rather than released on exit path. This bug is present in kernels starting from v3.2. Cc: stable@vger.kernel.org Signed-off-by:
-
Antonio Ospite authored
Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
-
Antonio Ospite authored
Move drivers/input/fixp-arith.h to include/linux so that the functions defined there can be used by other subsystems, for instance some video devices ISPs can control the output HUE value by setting registers for sin(HUE) and cos(HUE). Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Antonio Ospite authored
Also merge the "COLORS" control into it as it was V4L2_CID_SATURATION anyway. Signed-off-by:
-
Hans de Goede authored
Enabling vflip leads to a much better image, with vflip disabled the image looks washed out as if there is a too high brightness setting. Since we don't know how to lower the brightness setting when not vflipping, simply always vflip and tell userspace to flip the image back, resulting in a much better (less washed out) image. Since the image is now no longer too bright, also modify the luminance level the auto-gain algorithm aims for. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Hans de Goede authored
Our init sequence was not setting the register page to point to bank 1 before setting what should be the control reg. This causes the camera to sometimes have its LED on after init. First selecting register bank 1, rather then assuming the current register bank is bank 1, fixes this. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Now that the pac207 driver has been converted to the control framework, there are no remaining users. Signed-off-by:
-
Hans de Goede authored
The pac207's exposure control is a clock-divider, so it goes with quite big steps. So lets use an autogain algorithm optimised for that. Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans de Goede authored
We intend to eventually port all sub-drivers to the control-framework. At which point it will make more sense to have the ctrl_handler in gspca_dev then to have it in the subdrivers. Lets move it there now, to avoid a lot of work to move it later. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans de Goede authored
Now that stv06xx is using the control framework it is no longer necessary to have a (non const) copy of sd_desc inside the sd specific data struct. Signed-off-by:
-
Hans Verkuil authored
HdG: 1) Let the gspca-core cleanup the controls on control-init error, like with the other converted sub drivers 2) Note this also fixes a bug in the hdcs1020 support which was wrongly reporting an exposure range of 0-65535, even though the effective range was only 0-255 Signed-off-by:
-
Hans de Goede authored
Signed-off-by:
-
Hans Verkuil authored
HdG: Small fix: don't register some controls for sensors which don't have an implementation for them. Signed-off-by:
-
Hans Verkuil authored
The initial version was done by HV, corrections were made by HdG, and some final small changes again by HV. Signed-off-by:
-
Hans de Goede authored
Even with BRC the highest quality setting is not usable, BRC strips so much data from each MCU that the quality becomes worse then using a lower quality setting to begin with. Signed-off-by:
-
