The st1232 can switch from NORMAL to IDLE state after the configured
idle time (by default 8 s). If the st1232 is not reset during probe, it
might already be ready but in IDLE state. Since it does not enter NORMAL
state in this case, probe fails.

Fix the wait function to report the IDLE state as ready, too.

Fixes: f605be6a ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210219110556.1858969-1-m.tretter@pengutronix.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Olivier Crête <olivier.crete@ocrete.ca>
Link: https://lore.kernel.org/r/20210204005318.615647-1-olivier.crete@collabora.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There is a fork of this driver on GitHub [0] that has been updated
with new device IDs.

Merge those into the mainline driver, so the out-of-tree fork is not
needed for users of those devices anymore.

[0] https://github.com/paroj/xpadSigned-off-by: Benjamin Valentin <benpicco@googlemail.com>
Link: https://lore.kernel.org/r/20210121142523.1b6b050f@rechenknecht2k11Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Kernel test robot throws below warning ->

>> drivers/input/misc/ariel-pwrbutton.c:152:35: warning: unused variable
>> 'ariel_pwrbutton_id_table' [-Wunused-const-variable]
   static const struct spi_device_id ariel_pwrbutton_id_table[] = {
                                     ^
   1 warning generated.

Remove unused variable ariel_pwrbutton_id_table[] if no plan to use
it further.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/1608581041-4354-1-git-send-email-jrdr.linux@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.

This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.

This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.orgReviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Support for this chip is being added to the goodix driver: add the
DT binding for it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-3-angelogioacchino.delregno@somainline.orgReviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current description of ADC keys is not precise enough.

"when this key is pressed" leaves it open if a key is considered pressed
below or above the threshold. This has led to confusion:
drivers/input/keyboard/adc-keys.c ignores the meaning of thresholds and
sets the key that is closest to press-threshold-microvolt.

This patch nails down the definitions and provides an interpretation of the
supplied example.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201222110815.24121-1-xypron.glpk@gmx.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

g++ reports

	drivers/input/serio/i8042-x86ia64io.h:225:3: error: ‘.matches’ designator used multiple times in the same initializer list

C99 semantics is that last duplicated initialiser wins,
so DMI entry gets overwritten.

Fixes: a48491c6 ("Input: i8042 - add ByteSpeed touchpad to noloop table")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Link: https://lore.kernel.org/r/20201228072335.GA27766@localhost.localdomainSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.

If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution.  However, the latter may
happen before the device is ready, leading to a probe failure:

    st1232-ts 1-0055: Failed to read resolution: -6

Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.

On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller.  This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.

Optimize transfers by passing the wanted number of bytes.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type.  The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).

Fix this by subtracting 1.

Fixes: 3a54a215 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.11 merge window.

There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201214223109.82924-1-colin.king@canonical.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:

drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
   40 |  *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
  569 |  } __packed cmd;
      |             ^~~

Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.

Fixes: c2c06c41 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add new compatible strings and match data to support sc2730 and sc2721
which are two varieties of SC27XX family.
Signed-off-by: Nemo Han <nemo.han@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201117034949.47877-2-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add new compatible strings to support sc2730 and sc2721 which are
two varieties of SC27XX family.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117034949.47877-4-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the sprd sc27xx vibrator binding to DT schema using json-schema.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117034949.47877-3-zhang.lyra@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make use of generic touchscreen_properties structure to add axis
inversion and swapping capabilities. It's configurable via devicetree
properties:
  touchscreen-inverted-x
  touchscreen-inverted-y
  touchscreen-swapped-x-y
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Link: https://lore.kernel.org/r/20200922093903.157232-1-s.riedmueller@phytec.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhostSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().

Reported-and-tested-by: syzbot+150f793ac5bc18eee150@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If device is set up as a wakeup source, I2C core configures the interrupt
line as wake IRQ and PM core automatically configures it for waking up the
system on system suspend transition, so we do not have to explicitly call
enable_irq_wake() and disable_irq_wake() in suspend/resume.

Link: https://lore.kernel.org/r/20201120073920.3214492-2-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should not be configuring the controller as a wakeup source in the
driver, but rather rely on I2C core to mark it as such by either
instantiating as I2C_CLIENT_WAKEUP or specifying "wakeup-source" device
property.

Link: https://lore.kernel.org/r/20201120073920.3214492-1-dmitry.torokhov@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085032.2598-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211084957.2540-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adds support for the Dialog DA7280 LRA/ERM Haptic Driver with
multiple mode and integrated waveform memory and wideband support.
It communicates via an I2C bus to the device.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Reviewed-by: Jes Sorensen <Jes.Sorensen@gmail.com>.
Link: https://lore.kernel.org/r/1e293e8c4830b09255af3b7e1721b73afaefdfa3.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree binding information for DA7280 haptic driver.
Example bindings for DA7280 are added.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Reviewed-by: Rob Herring <robh@kernel.org>.
Link: https://lore.kernel.org/r/2bc9a4a9d083ea8f360ec75f6281b6de6c4ef284.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds the da7280 bindings doc and driver to the Dialog
Semiconductor support list.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Link: https://lore.kernel.org/r/e2a01173699486519f8da85b9283c6af8481fbdb.1606320459.git.Roy.Im@diasemi.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.twSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 0x5F is a new trackpoint report type used by some modules.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071511.32349-1-jingle.wu@emc.com.twSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add information found in downstream kernels, to make the code less
magic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/728fff020bc92be10d84cc2a7ea8af6fd99af96c.1607669375.git.mirq-linux@rere.qmqm.plSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Simplify the return expression.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201210135943.1612-1-zhengyongjun3@huawei.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add COMPILE_TEST support to imx_keypad driver for better compile
testing coverage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1583137573-16628-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20200227124534.23399-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200227130336.27042-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200228104508.15564-1-sergiu.cuciurean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of special-casing retrieval of number of X/Y electrodes based on
the firmware, let's select default values and mark registers as
non-existent on firmwares that do not support this operation.

Also mark "report rate" register as non-existent for generic firmwares
as having it set to 0 does not make sense.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Simon Budig <simon.budig@kernelconcepts.de>
Link: https://lore.kernel.org/r/X9FZFs3NZADoIhhH@google.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20201207071250.15021-1-chiu@endlessos.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.

Implement support for a "vddio-supply" that is enabled by the
tm2-touchkey driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201203131242.44397-3-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.

Document support for a "vddio-supply" that is enabled by the tm2-touchkey
driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201203131242.44397-2-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>