- 17 Nov, 2016 3 commits
-
-
Satish Kharat authored
Signed-off-by:
Satish Kharat <satishkh@cisco.com> Signed-off-by:
Sesidhar Baddela <sebaddel@cisco.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Don Brace authored
- driver was not calling done in some cases which causes the volume to be offlined. - avoid doing rescan during a reset. Reviewed-by:
Scott Teel <scott.teel@microsemi.com> Reviewed-by:
Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by:
Don Brace <don.brace@microsemi.com> Signed-off-by:
-
Tomas Henzl authored
It is not good when an irq arrives before driver structures are allocated. Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by:
-
- 14 Nov, 2016 5 commits
-
-
Colin Ian King authored
Use correct index on q, use h->intr_mode instead of i. Issue detected using static analysis with cppcheck Fixes: bc2bb154 ("scsi: hpsa: use pci_alloc_irq_vectors and automatic irq affinity") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Acked-by:
-
Colin Ian King authored
Trivial fix to typo "repsonse" to "response" in dev_dbg message. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake "suspeneded" to "suspended" in dev_warn messages. [mkp: corrected description. Patch is against the isci driver, not iscsi] Signed-off-by:
-
Colin Ian King authored
A couple of dev_printk messages spans two lines and the literal string is missing a white space between words. Add the white space. Signed-off-by:
-
Bart Van Assche authored
It is required to hold the queue lock when calling blk_run_queue_async() to avoid that a race between blk_run_queue_async() and blk_cleanup_queue() is triggered. Additionally, remove the get_device() and put_device() calls from fc_bsg_goose_queue. It is namely the responsibility of the caller of fc_bsg_goose_queue() to ensure that the bsg queue does not disappear while fc_bsg_goose_queue() is in progress. Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
- 12 Nov, 2016 5 commits
-
-
Ondrej Zary authored
When a SW-configurable card is specified but not found, the driver releases wrong region, causing the following message in kernel log: Trying to free nonexistent resource <0000000000000000-000000000000000f> Fix it by assigning base earlier. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Fixes: a8cfbcae ("scsi: g_NCR5380: Stop using scsi_module.c") Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
-
Kiwoong Kim authored
Some UFS host controller may need to configure some things around hibern8 enter/exit Signed-off-by:
Kiwoong Kim <kwmad.kim@samsung.com> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
Kiwoong Kim authored
Some UFS host controller may need to configure some things before any task management request is issued Signed-off-by:
-
Kiwoong Kim authored
Some UFS host controller may need to configure some things before any transfer request is issued. Signed-off-by:
-
Christoph Hellwig authored
This patch converts over hpsa to use the pci_alloc_irq_vectors including the PCI_IRQ_AFFINITY flag that automatically assigns spread out irq affinity to the I/O queues. It also cleans up the per-ctrl interrupt state due to the use of the pci_irq_vector and pci_free_irq_vectors helpers that don't need to know the exact irq type. Additionally it changes a little oddity in the existing code that was using different array indixes into the per-vector arrays depending on whether a controller is using a single INTx or single MSI irq. [mkp: fixed typo] Signed-off-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
- 09 Nov, 2016 1 commit
-
-
Chanwoo Choi authored
This patch uses the resource-managed to add the devfreq device. This function will make it easy to handle the devfreq device. - struct devfreq *devm_devfreq_add_device(struct device *dev, struct devfreq_dev_profile *profile, const char *governor_name, void *data); Cc: Vinayak Holikatti <vinholikatti@gmail.com> Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by:
-
- 08 Nov, 2016 26 commits
-
-
Colin Ian King authored
Trivial fix to spelling mistake "operatio" to "operation" in critical error message Signed-off-by:
-
Colin Ian King authored
Trivial fixes, minor spelling mistakes in comments and in a KERN_INFO message. [mkp: fixed spelling mistake in patch description] Signed-off-by:
-
Vivek Gautam authored
Host is allocated by managed kmalloc (devm_kmalloc). The memory allocated with this function is automatically freed on driver detach. So, no need to make an exclusive free call over it. Signed-off-by:
Vivek Gautam <vivek.gautam@codeaurora.org> Reviewed-by:
-
Vivek Gautam authored
Do a phy_exit() over the ufs phy in the ufs qcom exit path to de-initialize the phy. Signed-off-by:
-
Vivek Gautam authored
The common layer phy exit callback ufs_qcom_phy_exit() calls phy_power_off() that has no meaning when phy_power_off() callback is already registered with the phy provider and the consumer makes use of the same. Instead, add a no-op specific phy_exit() callback for now to add the exit sequence at a later point. Signed-off-by:
-
Vivek Gautam authored
Add phy clock enable code to phy_power_on/off callbacks, and remove explicit calls to enable these phy clocks from the ufs-qcom hcd driver. Signed-off-by:
-
Vivek Gautam authored
The phy init is meant to do phy initialization rather than just getting the clock and regulator. Move these clock and regulator get to probe(), to make room for actual phy initialization sequence. Signed-off-by:
-
Vivek Gautam authored
Move the functions' definitions to remove unnecessary declarations. Signed-off-by:
-
Vivek Gautam authored
remove() callback does a phy_power_off() only over the phy, and nothing else now. The phy_power_off() over the generic phy is called from the phy consumer, and phy provider driver should not explicitly need to call any phy ops. So discard the remove callback for qcom-ufs phy platform drivers. Signed-off-by:
-
Vivek Gautam authored
The tx_iface_clk and rx_iface_clk no longer exist with UFS Phy present on msm8996. So skip obtaining these clocks using compatible match. Signed-off-by:
-
Vivek Gautam authored
Add a new compatible string for 14nm ufs phy present on msm8996 chipset. This phy is bit different from the legacy 14nm ufs phy in terms of the clocks that are needed to be handled in the driver. Signed-off-by:
-
Vivek Gautam authored
Different menthods pass around generic phy pointer to extract device pointer. Instead, pass the device pointer directly between function calls. Signed-off-by:
-
Vivek Gautam authored
This helps us in avoiding any requirement for kfree() operation to be called exclusively over the allocated string pointer. Signed-off-by:
-
Vivek Gautam authored
BUG_ON() are not preferred in the driver, plus the variable on which BUG_ON is asserted is already checked in the code before passing. Signed-off-by:
-
Kashyap Desai authored
Signed-off-by:
-
Kashyap Desai authored
scsi: megaraid_sas: Do not set MPI2_TYPE_CUDA for JBOD FP path for FW which does not support JBOD sequence map CC: stable@vger.kernel.org Signed-off-by:
-
Kashyap Desai authored
Update MEGARAID drivers maintainers list. Signed-off-by:
-
Kashyap Desai authored
Until now the megaraid_sas driver has reported successful completion on SYNCHRONIZE_CACHE commands without sending them down to the controller. The controller firmware has been responsible for taking care of flushing disk caches for all drives that belong to a Virtual Disk at the time of system reboot/shutdown. There may have been a reason to avoid sending SYNCHRONIZE_CACHE to a VD in the past but that no longer appears to be valid. Older versions of MegaRaid firmware (Gen2 and Gen2.5) set the WCE bit for Virtual Disks but the firmware does not report correct completion status for a SYNCHRONIZE_CACHE command. As a result, we must use another method to identify whether it is safe to send the command to the controller. We use the canHandleSyncCache firmware flag in the scratch pad register at offset 0xB4. New SYNCHRONIZE_CACHE behavior: IF 'JBOD' Driver sends SYNCHRONIZE_CACHE command to the firmware Firmware sends SYNCHRONIZE_CACHE to drive Firmware obtains status from drive and returns same status back to driver ELSEIF 'VirtualDisk' IF firmware supports new API bit called canHandleSyncCache Driver sends SYNCHRONIZE_CACHE command to the firmware Firmware does not send SYNCHRONIZE_CACHE to drives Firmware returns SUCCESS ELSE Driver does not send SYNCHRONIZE_CACHE command to the firmware Driver return SUCCESS for that command ENDIF ENDIF [mkp: edited patch description] Signed-off-by:
Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
Which cleans up a lot of the MSI-X handling, and allows us to use the PCI IRQ layer provided vector mapping, which we can then expose to blk-mq. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Acked-by:
-
Christoph Hellwig authored
Just hand through the blk-mq map_queues method in the host template. Signed-off-by:
-
Christoph Hellwig authored
This will allow SCSI to have a single blk_mq_ops structure that either lets the LLDD map the queues to PCIe MSIx vectors or use the default. Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Subhash Jadavani authored
When we are resuming the UFS device rails in HPM mode, we are first powering on the VCC rail while VCCQ and VCCQ2 rails still being in LPM mode. Some UFS devices may take VCC on event as hint that host wants UFS device to be resumed and may start drawing more power from the VCCQ/VCCQ2 rails (while they are still in LPM mode) causing voltage drop on these rails. This change fixes this issue by bringing VCCQ & VCCQ2 rails out of LPM before powering on VCC rail. Reviewed-by:
Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by:
-
Subhash Jadavani authored
Currently clock scaling is suspended only after the host and device are put in low power mode but we should avoid clock scaling running after UFS link is put in low power mode (hibern8). This change suspends clock scaling before putting host/device in low power mode. Reviewed-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
-
Subhash Jadavani authored
If ufshcd pltfrm/pci driver's probe fails for some reason then ensure that scsi host is released to avoid memory leak but managed memory allocations (via devm_* calls) need not to be freed explicitly on probe failure as memory allocated with these functions is automatically freed on driver detach. Reviewed-by:
-
Subhash Jadavani authored
UFS devfreq clock scaling work may require clocks to be ON if it need to execute some UFS commands hence it may request for clock hold before issuing the command. But if UFS clock gating work is already running in parallel, ungate work would end up waiting for the clock gating work to finish and as clock gating work would also wait for the clock scaling work to finish, we would enter in deadlock state. Here is the call trace during this deadlock state: Workqueue: devfreq_wq devfreq_monitor __switch_to __schedule schedule schedule_timeout wait_for_common wait_for_completion flush_work ufshcd_hold ufshcd_send_uic_cmd ufshcd_dme_get_attr ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div ufs_qcom_clk_scale_notify ufshcd_scale_clks ufshcd_devfreq_target update_devfreq devfreq_monitor process_one_work worker_thread kthread ret_from_fork Workqueue: events ufshcd_gate_work __switch_to __schedule schedule schedule_preempt_disabled __mutex_lock_slowpath mutex_lock devfreq_monitor_suspend devfreq_simple_ondemand_handler devfreq_suspend_device ufshcd_gate_work process_one_work worker_thread kthread ret_from_fork Workqueue: events ufshcd_ungate_work __switch_to __schedule schedule schedule_timeout wait_for_common wait_for_completion flush_work __cancel_work_timer cancel_delayed_work_sync ufshcd_ungate_work process_one_work worker_thread kthread ret_from_fork This change fixes this deadlock by doing this in devfreq work (devfreq_wq): Try cancelling clock gating work. If we are able to cancel gating work or it wasn't scheduled, hold the clock reference count until scaling is in progress. If gate work is already running in parallel, let's skip the frequecy scaling at this time and it will be retried once next scaling window expires. Reviewed-by:
-
Suganath Prabu Subramani authored
Signed-off-by:
Chaitra P B <chaitra.basappa@broadcom.com> Signed-off-by:
Sathya Prakash <sathya.prakash@broadcom.com> Signed-off-by:
Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by:
-
