Add stubs to retrieve a handle to an IPv6 FIB table, fib6_get_table,
a stub to do a lookup in a specific table, fib6_table_lookup, and
a stub for a full route lookup.

The stubs are needed for core bpf code to handle the case when the
IPv6 module is not builtin.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Similar to IPv4, IPv6 should use the FIB lookup result in the
tracepoint.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Add IPv6 equivalent to fib_lookup. Does a fib lookup, including rules,
but returns a FIB entry, fib6_info, rather than a dst based rt6_info.
fib6_lookup is any where from 140% (MULTIPLE_TABLES config disabled)
to 60% faster than any of the dst based lookup methods (without custom
rules) and 25% faster with custom rules (e.g., l3mdev rule).

Since the lookup function has a completely different signature,
fib6_rule_action is split into 2 paths: the existing one is
renamed __fib6_rule_action and a new one for the fib6_info path
is added. fib6_rule_action decides which to call based on the
lookup_ptr. If it is fib6_table_lookup then the new path is taken.

Caller must hold rcu lock as no reference is taken on the returned
fib entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Move source address lookup from fib6_rule_action to a helper. It will be
used in a later patch by a second variant for fib6_rule_action.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

ip6_pol_route is used for ingress and egress FIB lookups. Refactor it
moving the table lookup into a separate fib6_table_lookup that can be
invoked separately and export the new function.

ip6_pol_route now calls fib6_table_lookup and uses the result to generate
a dst based rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Rename rt6_multipath_select to fib6_multipath_select and export it.
A later patch wants access to it similar to IPv4's fib_select_path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Rename fib6_lookup to fib6_node_lookup to better reflect what it
returns. The fib6_lookup name will be used in a later patch for
an IPv6 equivalent to IPv4's fib_lookup.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

For me, as a reader whose mother language isn't English, the
old words bring a little difficulty to catch the meaning, this
patch rewords the subsection in a more clarificatory way.

This patch also add blank lines as separator at two places
to improve readability.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Update .gitignore files.
Signed-off-by: Sirio Balmelli <sirio@b-ad.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The BPF selftests fail to build with missing headers
'asm/bitsperlong.h' and 'asm/errno.h'.

These already exist in 'tools/arch/[arch]/include';
add architecture-agnostic header files in 'tools/include/uapi'
to reference them.
Signed-off-by: Sirio Balmelli <sirio@b-ad.ch>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

i386 builds report:
  net/xdp/xdp_umem.o: In function `xdp_umem_reg':
  xdp_umem.c:(.text+0x47e): undefined reference to `__udivdi3'

This fix uses div_u64 instead of the GCC built-in.

Fixes: c0c77d8f ("xsk: add user memory registration support sockopt")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Jakub Kicinski says:

====================
This small series adds a feature which extends BPF offload beyond
a pure host processing offload and firmly into the realm of
heterogeneous processing.  Allowing offloaded XDP programs to set
the RX queue index opens the door for defining fully programmable
RSS/n-tuple filter replacement.  In fact the device datapath will
skip the RSS processing completely if BPF decided on the queue
already, making the XDP program replace part of the standard NIC
datapath.

We hope some day the entire NIC datapath will be defined by BPF :)
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>

BPF has access to all internal FW datapath structures.  Including
the structure containing RX queue selection.  With little coordination
with the datapath we can let the offloaded BPF select the RX queue.
We just need a way to tell the datapath that queue selection has already
been done and it shouldn't overwrite it.  Define a bit to tell datapath
BPF already selected a queue (QSEL_SET), if the selected queue is not
enabled (>= number of enabled queues) datapath will perform normal RSS.

BPF queue selection on the NIC can be used to replace standard
datapath RSS with fully programmable BPF/XDP RSS.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

It's fairly easy for offloaded XDP programs to select the RX queue
packets go to.  We need a way of expressing this in the software.
Allow write to the rx_queue_index field of struct xdp_md for
device-bound programs.

Skip convert_ctx_access callback entirely for offloads.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Martin KaFai Lau says:

====================
This series introduces BTF ID which is exposed through
the new BPF_BTF_GET_FD_BY_ID cmd, new "struct bpf_btf_info"
and new members in the "struct bpf_map_info".

Please see individual patch for details.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch adds test for BPF_BTF_GET_FD_BY_ID and the new
btf_id/btf_key_id/btf_value_id in the "struct bpf_map_info".

It also modifies the existing BPF_OBJ_GET_INFO_BY_FD test
to reflect the new "struct bpf_btf_info".
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch sync the tools/include/uapi/linux/btf.h with
the newly introduced BTF ID support.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch adds a CHECK() macro for condition checking
and error report purpose.  Something similar to test_progs.c

It also counts the number of tests passed/skipped/failed and
print them at the end of the test run.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

During BPF_OBJ_GET_INFO_BY_FD on a btf_fd, the current bpf_attr's
info.info is directly filled with the BTF binary data.  It is
not extensible.  In this case, we want to add BTF ID.

This patch adds "struct bpf_btf_info" which has the BTF ID as
one of its member.  The BTF binary data itself is exposed through
the "btf" and "btf_size" members.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch gives an ID to each loaded BTF.  The ID is allocated by
the idr like the existing prog-id and map-id.

The bpf_put(map->btf) is moved to __bpf_map_put() so that the
userspace can stop seeing the BTF ID ASAP when the last BTF
refcnt is gone.

It also makes BTF accessible from userspace through the
1. new BPF_BTF_GET_FD_BY_ID command.  It is limited to CAP_SYS_ADMIN
   which is inline with the BPF_BTF_LOAD cmd and the existing
   BPF_[MAP|PROG]_GET_FD_BY_ID cmd.
2. new btf_id (and btf_key_id + btf_value_id) in "struct bpf_map_info"

Once the BTF ID handler is accessible from userspace, freeing a BTF
object has to go through a rcu period.  The BPF_BTF_GET_FD_BY_ID cmd
can then be done under a rcu_read_lock() instead of taking
spin_lock.
[Note: A similar rcu usage can be done to the existing
       bpf_prog_get_fd_by_id() in a follow up patch]

When processing the BPF_BTF_GET_FD_BY_ID cmd,
refcount_inc_not_zero() is needed because the BTF object
could be already in the rcu dead row .  btf_get() is
removed since its usage is currently limited to btf.c
alone.  refcount_inc() is used directly instead.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

If CONFIG_REFCOUNT_FULL=y, refcount_inc() WARN when refcount is 0.
When creating a new btf, the initial btf->refcnt is 0 and
triggered the following:

[   34.855452] refcount_t: increment on 0; use-after-free.
[   34.856252] WARNING: CPU: 6 PID: 1857 at lib/refcount.c:153 refcount_inc+0x26/0x30
....
[   34.868809] Call Trace:
[   34.869168]  btf_new_fd+0x1af6/0x24d0
[   34.869645]  ? btf_type_seq_show+0x200/0x200
[   34.870212]  ? lock_acquire+0x3b0/0x3b0
[   34.870726]  ? security_capable+0x54/0x90
[   34.871247]  __x64_sys_bpf+0x1b2/0x310
[   34.871761]  ? __ia32_sys_bpf+0x310/0x310
[   34.872285]  ? bad_area_access_error+0x310/0x310
[   34.872894]  do_syscall_64+0x95/0x3f0

This patch uses refcount_set() instead.
Reported-by: Yonghong Song <yhs@fb.com>
Tested-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

If the example binding is used on a real dts file, the following DTC
warning is seen with W=1:

arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Remove unnecessary #address-cells/#size-cells to improve the binding
document examples.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When computing the bitrate using values read from an SFP module EEPROM,
we use the nominal BR plus BR,min and BR,max to determine the
boundaries. But in some cases BR,min and BR,max aren't provided, which
led the SFP code to end up having the nominal value for both the minimum
and maximum bitrate values. When using a passive cable, the nominal
value should be used as the maximum one, and there is no minimum one
so we should use 0.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Fixes for net-next.

This series includes a bug fix for a regression in firmware message polling
introduced recently on net-next.  There are 3 additional minor fixes for
unsupported link speed checking, VF MAC address handling, and setting
PHY eeprom length.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code already forwards the VF MAC address to the PF, except
in one case.  If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address.  This
causes "ip link show" to show zero VF MAC addresses for this case.

This assumption is not correct.  Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe.  So we need to always forward the VF MAC address to the PF.

The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.

Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only non-NPAR PFs need to actively check and manage unsupported link
speeds.  NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression.  With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.

Increase the maximum wait time from 5 usec to 20 usec.  Also, fix
the debug message that shows the total delay time for the response
when the message times out.  With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.

Fixes: 9751e8e7 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds PCI device IDs to support 25GE and 100GE card:

1. Add device id 0x0201 for HINIC 100GE dual port card.
2. Add device id 0x0200 for HINIC 25GE dual port card.
3. Macro of device id 0x1822 is modified for HINIC 25GE quad port card.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change fixes a couple of type mismatch reported by the sparse
tool, explicitly using the requested type for the offending arguments.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the core networking needs to detect the transport offset in a given
packet and parse it explicitly, a full-blown flow_keys struct is used for
storage.
This patch introduces a smaller keys store, rework the basic flow dissect
helper to use it, and apply this new helper where possible - namely in
skb_probe_transport_header(). The used flow dissector data structures
are renamed to match more closely the new role.

The above gives ~50% performance improvement in micro benchmarking around
skb_probe_transport_header() and ~30% around eth_get_headlen(), mostly due
to the smaller memset. Small, but measurable improvement is measured also
in macro benchmarking.

v1 -> v2: use the new helper in eth_get_headlen() and skb_get_poff(),
  as per DaveM suggestion
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Minor conflict in ip_output.c, overlapping changes to
the body of an if() statement.
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
net/ipv6 misc

This patchset contains two patches for net/ipv6.

Patch 1 is a trivial typo fix in documentation.
Patch 2 by Eran is a re-spin. It adds GRO support for IPv6 GRE tunnel,
this significantly improves performance in case GRO in native interface
is disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add GRO capability for IPv6 GRE tunnel and ip6erspan tap, via gro_cells
infrastructure.

Performance testing: 55% higher badwidth.
Measuring bandwidth of 1 thread IPv4 TCP traffic over IPv6 GRE tunnel
while GRO on the physical interface is disabled.
CPU: Intel Xeon E312xx (Sandy Bridge)
NIC: Mellanox Technologies MT27700 Family [ConnectX-4]
Before (GRO not working in tunnel) : 2.47 Gbits/sec
After  (GRO working in tunnel)     : 3.85 Gbits/sec
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix 'an' into 'and', and use a comma instead of a period.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: Add support for new multi partitioning modes.

The patch series simplifies the multi function (MF) mode implementation of
qed/qede drivers, and adds support for new MF modes.

Please consider applying it to net-next branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>