The i2c-ali1535 driver doesn't work on SPARC, because it assumes that
ioport address are 16-bit wide (address stored in an unsigned short).
But on SPARC arch, ioports are mapped in memory and so must be stored
in an unsigned long.

Use pci_resource_start for getting IOMEM base address, then read the
SMBBA of the i2c bus and use these together for I/O access.

I would like to thank Jean DELVARE for reviewing my patch.
Signed-off-by: LABBE Corentin <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

When adding checks for ACPI resource conflicts to many bus drivers,
not enough attention was paid to the error paths, and for several
drivers this causes 0 to be returned on error in some cases. Fix this
by properly returning a non-zero value on every error.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
  ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
  ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
  ALSA: usb-audio: add Yamaha MOX6/MOX8 support
  ALSA: virtuoso: add S/PDIF input support for all Xonars
  ALSA: ice1724 - Support for ooAoo SQ210a
  ALSA: ice1724 - Allow card info based on model only
  ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
  ALSA: hdspm - Provide unique driver id based on card serial
  ASoC: Dynamically allocate the rtd device for a non-empty release()
  ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
  ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
  ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
  ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
  ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
  ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
  ALSA: hda/cirrus - support for iMac12,2 model
  ASoC: cx20442: add bias control over a platform provided regulator
  ALSA: usb-audio - Avoid flood of frame-active debug messages
  ALSA: snd-usb-us122l: Delete calls to preempt_disable
  mfd: Put WM8994 into cache only mode when suspending
  ...

Fix up trivial conflicts in:
 - arch/arm/mach-s3c64xx/mach-crag6410.c:
	renamed speyside_wm8962 to tobermory, added littlemill right
	next to it
 - drivers/base/regmap/{regcache.c,regmap.c}:
	duplicate diff that had already come in with other changes in
	the regmap tree

We only need amd_bus.o for AMD systems with PCI.  arch/x86/pci/Makefile
already depends on CONFIG_PCI=y, so this patch just adds the dependency
on CONFIG_AMD_NB.

Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org	# 2.6.34+ (needs adjustment for k8 -> amd rename)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc

SH/R-Mobile updates for 3.3 merge window.

* tag 'rmobile-for-linus' of git://github.com/pmundt/linux-sh: (32 commits)
  arm: mach-shmobile: add a resource name for shdma
  ARM: mach-shmobile: r8a7779 SMP support V3
  ARM: mach-shmobile: Add kota2 defconfig.
  ARM: mach-shmobile: Add marzen defconfig.
  ARM: mach-shmobile: r8a7779 power domain support V2
  ARM: mach-shmobile: Fix up marzen build for recent GIC changes.
  ARM: mach-shmobile: r8a7779 PFC function support
  ARM: mach-shmobile: Flush caches in platform_cpu_die()
  ARM: mach-shmobile: Allow SoC specific CPU kill code
  ARM: mach-shmobile: Fix headsmp.S code to use CPUINIT
  ARM: mach-shmobile: clock-r8a7779: clkz/clkzs support
  ARM: mach-shmobile: clock-r8a7779: add DIV4 clock support
  ARM: mach-shmobile: Marzen LAN89218 support
  ARM: mach-shmobile: Marzen SCIF2/SCIF4 support
  ARM: mach-shmobile: r8a7779 PFC GPIO-only support V2
  ARM: mach-shmobile: r8a7779 and Marzen base support V2
  sh: pfc: Unlock register support
  sh: pfc: Variable bitfield width config register support
  sh: pfc: Add config_reg_helper() function
  sh: pfc: Convert index to field and value pair
  ...

SuperH updates for 3.3 merge window.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (38 commits)
  sh: magicpanelr2: Update for parse_mtd_partitions() fallout.
  sh: mach-rsk: Update for parse_mtd_partitions() fallout.
  sh: sh2a: Improve cache flush/invalidate functions
  sh: also without PM_RUNTIME pm_runtime.o must be built
  sh: add a resource name for shdma
  sh: Remove redundant try_to_freeze() invocations.
  sh: Ensure IRQs are enabled across do_notify_resume().
  sh: Fix up store queue code for subsys_interface changes.
  sh: clkfwk: sh_clk_init_parent() should be called after clk_register()
  sh: add platform_device for renesas_usbhs in board-sh7757lcr
  sh: modify clock-sh7757 for renesas_usbhs
  sh: pfc: ioremap() support
  sh: use ioread32/iowrite32 and mapped_reg for div6
  sh: use ioread32/iowrite32 and mapped_reg for div4
  sh: use ioread32/iowrite32 and mapped_reg for mstp32
  sh: extend clock struct with mapped_reg member
  sh: clkfwk: clock-sh73a0: all div6_clks use SH_CLK_DIV6_EXT()
  sh: clkfwk: clock-sh7724: all div6_clks use SH_CLK_DIV6_EXT()
  sh: clock-sh7723: add CLKDEV_ICK_ID for cleanup
  serial: sh-sci: Handle GPIO function requests.
  ...

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix lockup by limiting load-balance retries on lock-break
  sched: Fix CONFIG_CGROUP_SCHED dependency
  sched: Remove empty #ifdefs

Follows the RSK+ change for the same rationale.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The RSK+ setup code was doing some pretty dubious things with
parse_mtd_partitions() in order to populate the physmap-flash map
platform data. The physmap-flash driver contains all of the functionality
that we require already, so simply drop the special casing and pad out
the platform data accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The cache functions lock out interrupts for long periods; this patch
reduces the impact when operating on large address ranges. In such
cases it will:
- Invalidate the entire cache rather than individual addresses.
- Do nothing when flushing the operand cache in write-through mode.
- When flushing the operand cache in write-back mdoe, index the
  search for matching addresses on the cache entires instead of the
  addresses to flush

Note: sh2a__flush_purge_region was only invalidating the operand
cache, this adds flush.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Conflicts:
	arch/sh/kernel/cpu/sh4a/clock-sh7723.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

When CONFIG_PM_RUNTIME is off, drivers/sh/pm_runtime.o still has to be
built on sh platforms, because then it provides means to statically
switch on device PM clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel config: Fix the APB_TIMER selection
  x86/mrst: Add additional debug prints for pb_keys
  x86/intel config: Revamp configuration to allow for Moorestown and Medfield
  x86/intel/scu/ipc: Match the changes in the x86 configuration
  x86/apb: Fix configuration constraints
  x86: Fix INTEL_MID silly
  x86/Kconfig: Cyclone-timer depends on x86-summit
  x86: Reduce clock calibration time during slave cpu startup
  x86/config: Revamp configuration for MID devices
  x86/sfi: Kill the IRQ as id hack

* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, reboot: Fix typo in nmi reboot path
  x86, NMI: Add to_cpumask() to silence compile warning
  x86, NMI: NMI selftest depends on the local apic
  x86: Add stack top margin for stack overflow checking
  x86, NMI: NMI-selftest should handle the UP case properly
  x86: Fix the 32-bit stackoverflow-debug build
  x86, NMI: Add knob to disable using NMI IPIs to stop cpus
  x86, NMI: Add NMI IPI selftest
  x86, reboot: Use NMI instead of REBOOT_VECTOR to stop cpus
  x86: Clean up the range of stack overflow checking
  x86: Panic on detection of stack overflow
  x86: Check stack overflow in detail

* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, efi: Break up large initrd reads
  x86, efi: EFI boot stub support
  efi: Add EFI file I/O data types
  efi.h: Add boottime->locate_handle search types
  efi.h: Add graphics protocol guids
  efi.h: Add allocation types for boottime->allocate_pages()
  efi.h: Add efi_image_loaded_t
  efi.h: Add struct definition for boot time services
  x86: Don't use magic strings for EFI loader signature
  x86: Add missing bzImage fields to struct setup_header

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/numa: Add constraints check for nid parameters
  mm, x86: Remove debug_pagealloc_enabled
  x86/mm: Initialize high mem before free_all_bootmem()
  arch/x86/kernel/e820.c: quiet sparse noise about plain integer as NULL pointer
  arch/x86/kernel/e820.c: Eliminate bubble sort from sanitize_e820_map()
  x86: Fix mmap random address range
  x86, mm: Unify zone_sizes_init()
  x86, mm: Prepare zone_sizes_init() for unification
  x86, mm: Use max_low_pfn for ZONE_NORMAL on 64-bit
  x86, mm: Wrap ZONE_DMA32 with CONFIG_ZONE_DMA32
  x86, mm: Use max_pfn instead of highend_pfn
  x86, mm: Move zone init from paging_init() on 64-bit
  x86, mm: Use MAX_DMA_PFN for ZONE_DMA on 32-bit

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
  [CPUFREQ] EXYNOS: Removed useless headers and codes
  [CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
  [CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
  [CPUFREQ] powernow-k8: Fix indexing issue
  [CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
  [CPUFREQ] update lpj only if frequency has changed
  [CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
  [CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
  [CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
  [CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
  [CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
  [CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
  cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
  cpufreq: OMAP: fix freq_table leak
  cpufreq: OMAP: put clk if cpu_init failed
  cpufreq: OMAP: only supports OPP library
  cpufreq: OMAP: dont support !freq_table
  cpufreq: OMAP: deny initialization if no mpudev
  cpufreq: OMAP: move clk name decision to init
  cpufreq: OMAP: notify even with bad boot frequency
  ...

* git://git.infradead.org/battery-2.6: (68 commits)
  power_supply: Mark da9052 driver as broken
  power_supply: Drop usage of nowarn variant of sysfs_create_link()
  s3c_adc_battery: Average over more than one adc sample
  power_supply: Add DA9052 battery driver
  isp1704_charger: Fix missing check
  jz4740-battery: Fix signedness bug
  power_supply: Assume mains power by default
  sbs-battery: Fix devicetree match table
  ARM: rx51: Add bq27200 i2c board info
  sbs-battery: Change power supply name
  devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
  devicetree-bindings: Add vendor entry for Smart Battery Systems
  sbs-battery: Rename internals to new name
  bq20z75: Rename to sbs-battery
  wm97xx_battery: Use DEFINE_MUTEX() for work_lock
  max8997_charger: Remove duplicate module.h
  lp8727_charger: Some minor fixes for the header
  lp8727_charger: Add header file
  power_supply: Convert drivers/power/* to use module_platform_driver()
  power_supply: Add "unknown" in power supply type
  ...

* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  slub: disallow changing cpu_partial from userspace for debug caches
  slub: add missed accounting
  slub: Extract get_freelist from __slab_alloc
  slub: Switch per cpu partial page support off for debugging
  slub: fix a possible memleak in __slab_alloc()
  slub: fix slub_max_order Documentation
  slub: add missed accounting
  slab: add taint flag outputting to debug paths.
  slub: add taint flag outputting to debug paths
  slab: introduce slab_max_order kernel parameter
  slab: rename slab_break_gfp_order to slab_max_order

Two bugfixes for md.

One is a recently introduced regression that affects an unusual
configuration with a guaranteed BUG_ON.  Has been tagged for -stable.
The other is minor missing functionality.

* tag 'md-3.3-fixes' of git://neil.brown.name/md:
  md/raid1: perform bad-block tests for WriteMostly devices too.
  md: notify the 'degraded' sysfs attribute on failure.

* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
  x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
  PCI: Increase resource array mask bit size in pcim_iomap_regions()
  PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
  PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
  PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
  x86/PCI: amd: factor out MMCONFIG discovery
  PCI: Enable ATS at the device state restore
  PCI: msi: fix imbalanced refcount of msi irq sysfs objects
  PCI: kconfig: English typo in pci/pcie/Kconfig
  PCI/PM/Runtime: make PCI traces quieter
  PCI: remove pci_create_bus()
  xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
  x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
  x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
  x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
  sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
  sparc/PCI: convert to pci_create_root_bus()
  sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
  powerpc/PCI: convert to pci_create_root_bus()
  powerpc/PCI: split PHB part out of pcibios_map_io_space()
  ...

Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.

This patch contains r8a7779 SMP support V3 - now including
CPU hotplug offine and online support. The r8a7779 power
domain code is tied together with SMP glue code which allows
us to control the power domains via CPU hotplug.

At this point the kernel boots with the 4 Cortex-A9 cores in
SMP mode and all CPU cores except CPU0 can be hotplugged.

The code in platsmp.c is quite far from pretty, but it is
kept like that intentionally to avoid creating layers of
code that will go away in the near future anyway. The code
needs to be updated when some per-SoC handling code will be
added to the ARM architecture, see the following patch for
more information:
 "[RFC PATCH 0/3] Per SoC descriptor"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

frv, h8300, m68k, microblaze, openrisc, score, um and xtensa currently
do not register a CPU device.  Add the config option GENERIC_CPU_DEVICES
which causes a generic CPU device to be registered for each present CPU,
and make all these architectures select it.

Richard Weinberger <richard@nod.at> covered UML and suggested using
per_cpu.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpu_dev_init() is only called from driver_init(), which does not check
its return value.  Therefore make cpu_dev_init() return void.

We must register the CPU subsystem, so panic if this fails.

If sched_create_sysfs_power_savings_entries() fails, the damage is
contained, so ignore this (as before).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Eric and David reported dead machines and traced it to commit
a195f004 ("sched: Fix load-balance lock-breaking"), it turns out
there's still a scenario where we can end up re-trying forever.

Since there is no strict forward progress guarantee in the
load-balance iteration we can get stuck re-retrying the same
task-set over and over.

Creating a forward progress guarantee with the existing
structure is somewhat non-trivial, for now simply terminate the
retry loop after a few tries.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: David Ahern <dsahern@gmail.com>
[ logic cleanup as suggested by Eric ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1326297936.2442.157.camel@twinsSigned-off-by: Ingo Molnar <mingo@elte.hu>

The DL1 PDM interface adds a little gain depending on the output device.
Add a method to retrieve the gain value for machine driver usage.
Signed-off-by: Liam Girdwood <lrg@ti.com>

When multiple headphone or other detectable output pins are present,
the power-map has to be updated after resume appropriately, but the
current driver doesn't check all pins but only the first pin (since
it's enough to check it for the mute-behavior).  This resulted in the
silent output from the secondary outputs after PM resume.

This patch fixes the problem by checking all pins at (re-)init time.

Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=740347

Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

All Xonar cards support S/PDIF input, but the cards without optical or
coaxial plugs have only undocumented pin connectors.  Support for the
ST/STX was already added in a previous patch; this adds support for the
D1/DX (JP2), DG (J5), DS (J5), and HDAV Slim (J12).

Many thanks to Zoltan Miklos for testing the DS and DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This card shares PCI ids with Chaintec AV710. Therefore, it will not be
detected automatically, it can only be activated by the module parameter
model=sq210a.
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>