Disallow having more than one IBSS interface up at any time
because of beacon distribution issues, and for now also disallow
having more than one IBSS/STA interface up at the same time
because we use the master interface's BSS struct which would
be completely corrupted when we have more than one up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a STA structure is added, it is often checked whether it
already exists before adding it. This, however, isn't done
atomically so there is a race condition that could lead to two
STA structures being added with the same MAC address. This
patch changes sta_info_add() to return an ERR_PTR in case
of failure and adds the failure mode -EEXIST when the STA
already exists.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This reworks the code for TX filtered frames, splitting it out to
a new function to handle those cases, making the clear instruction
a flag and renaming a few things to be easier to understand and
less Atheros hardware specific. Finally, it also makes the comments
explain more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Configuration variables are only available to the preprocessor
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes a few sparse warnings in p54.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Both of these seem to be actual errors, the first is just wrong
and the second is my mistake introduced by the cfg80211 API
update.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds support for 8bit wide register reads/writes.
This is needed in order to support the gigabit ethernet core.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This consolidates all TIM handling code to avoid re-introducing
errors with the bitmap/set_tim order and to reduce code. While
reading the code I noticed a possible problem so I also added
a comment about that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The TIM flag that is kept in each station's info is completely
useless, there's no code (aside from the debugfs display code)
checking it, hence it can be removed. While doing that, I noticed
that the TIM handling is broken when buffered frames expire, so
fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Drivers should be allowed to simply get a complete new beacon when
set_tim() is invoked (and set_tim() is required for drivers that
just want a beacon template!), so we need to update our own TIM
bitmap before calling set_tim() so that getting the beacon will
now get an already updated beacon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Convert list_for_each_rcu() to list_for_each_entry_rcu()
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds channels to US regulatory domain
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The MAC address offset defines were incorrect because
the byte offset was used instead of word index. This
bug had no affect on normal operations since these
defines weren't used. (EEPROM_MAC_ADDR_0 was used
to read 6 bytes from).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The supported_bands field of struct hw_mode_spec now represents a bitfield,
so bitfield operators need to be tested with when setting the band data.

The current code generates the following warning:

[176624.986244] WARNING: at /usr/local/src/incoming/compat-wireless-2.6/net/wireless/core.c:269 wiphy_register()
[176624.986249] Pid: 12548, comm: modprobe Tainted: P        2.6.24.2#4
[176624.986251]
[176624.986251] Call Trace:
[176624.986277]  [<ffffffff881c56bf>] :cfg80211:wiphy_register+0x17f/0x1a0
[176624.986282]  [<ffffffff881ddf80>] :rt61pci:rt61pci_eepromregister_write+0x0/0x80
[176624.986302]  [<ffffffff88b7e4bc>] :mac80211:ieee80211_register_hw+0x2c/0x2b0
[176624.986310]  [<ffffffff881cdc80>] :rt2x00lib:rt2x00lib_probe_dev+0x350/0x3f0
[176624.986318]  [<ffffffff881d74b9>] :rt2x00pci:rt2x00pci_probe+0x149/0x200
[176624.986325]  [<ffffffff8030c858>] pci_device_probe+0xf8/0x170
[176624.986331]  [<ffffffff803594fc>] driver_probe_device+0x9c/0x1c0
[176624.986335]  [<ffffffff80359700>] __driver_attach+0x0/0xb0
[176624.986337]  [<ffffffff803597a5>] __driver_attach+0xa5/0xb0
[176624.986341]  [<ffffffff8035877d>] bus_for_each_dev+0x4d/0x80
[176624.986347]  [<ffffffff80358b8c>] bus_add_driver+0xac/0x210
[176624.986351]  [<ffffffff8030cad3>] __pci_register_driver+0x73/0xc0
[176624.986357]  [<ffffffff8025689e>] sys_init_module+0x18e/0x1a20
[176624.986374]  [<ffffffff8020c42e>] system_call+0x7e/0x83
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The async vendor requests are a ugly hack which is not working correctly.
The proper fix for the scheduling while atomic issue is finding out why
we can't use led classes for USB drivers and fix that.

Just replace all async calls with the regular ones and print an
error for the disallowed LED configuration attempts. That will
help in determining which led class is causing the problem.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't wildly pass any number for num_rates to rt2x00lib,
instead pass which type of rates are supported (CCK, OFDM).
Same for num_modes but then for the 2GHZ and 5GHZ band.

This makes the interface look much nicer and makes
extending it later easier.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The dscape stack was renamed to mac80211 a long time ago,
we are long overdue with fixing all comments to reflect this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specifications indicate the TSF registers are read-only,
so there is no point in writing 0 to those registers.

As far as I know there isn't another way to reset the
TSF registers. So removing these callbacks will notify
mac80211 about the lack of support.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As Adam Baker reported the DMA address for the
descriptor base was incorrectly initialized in
the PCI drivers.

Instead of the DMA base for the descriptor, the
DMA base for the data was passed resulting in a
broken TX/RX state for PCI drivers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ACK_CTS frame is a control frame, this means
dropping the frame depends on the FIF_CONTROL flag
for filtering.

This also fixes an obvious typo in register definition.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a new flag for the skb_frame_desc structure which is used to tag
rts/cts frames that are generated by the driver. Through the tag we can
recognize frames we have generated ourselves, so we don't report their tx
status to mac80211.

This patch is based on the original patch by
Mattias Nissler <mattias.nissler@gmx.de>.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 sends the txpower to use during config(),
we already store it in the rt2x00_dev structure.
When writing the descriptor correctly initialize
the txpower field with this value to make sure
all frames are send out with the correct tx power.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the radio is being disabled we should also
kill the guardian urb which could still be pending
in the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Simplify the way rt2x00 assigns new objects to the
rt2x00lib module. This saves a few if statements
and overall does this looks much nicer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As Adam Baker reported the queue->qid was not initialized
correctly. The QID_AC_BE was assigned to the RX ring.

This will move the queue initialization into a seperate function
and makes sure that all queues are initialized directly with the
correct qids.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

skbdesc->data_len was not initialized correctly
in rt2x00pci, rt2x00usb, rt2500usb and rt73usb.

The value was set to queue->data_size which
means that the incorrect frame size was pased
to the upper layers.

Correctly base the value on either the skb->len,
or the rx frame size passed to the driver by the
device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The second eeprom recovery message is about
the RSSI offset for ieee802.11 A.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rename "frame" folder to "queue" folder,
add extra file to this folder which contains
statistics about all hardware queues. This will
help debugging and spotting problems in the
queue indexing system.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Call rt2x00_config_intf() outside of the spinlock context since
the call will sleep for USB drivers. By using the ieee80211_if_conf
values as arguments we make keep access tp rt2x00_intf thread safe
even without the lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The csr_cache and csr_addr pointers are both the same size
and they are never used both by the same driver. This makes
them a nice candidate for an union.
We could merge into 1 pointer, but that would either upset sparse,
or require a lot of __force casts.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Select CONFIG_NEW_LEDS before selecting the other LED config
options. This fixes a link error when NEW_LEDS was disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When calculating the offset to add to the queue entry base to get the
individual entry's private data area the base address must be treated
as a char * not a struct queue_entry so we can do byte oriented
pointer arithmetic with it.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the last remnants of the MGMT ring initialization
from rt61pci.ko
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove the debug messages regarding initialization from
EEPROM. The values are vendor specific, and are not really
needed for debug purposes. If they ever become usefull we
still have access to them through debugfs which also
prints the exact same values...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Be more strict when using the queue_entry_priv_pci_rx
and queue_entry_priv_pci_tx structures. Only use a
particular type that matches the queue type.

When freeing the DMA the priv_tx->data and priv_tx->dma
was used. This is incorrect since the start of the DMA
was in fact the priv_tx->desc pointer. Instead of
recalculating the dma_addr_t for the DMA start this
patch will swap the data and descriptor part of the
allocated memory.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Michael Büker <m.bueker@berlin.de> reports that the RT2x00 drivers
are not indented as they should be, so use proper dependencies to make
them be indented as expected.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Ack-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The semaphore wpa_sem is used as mutex, convert it to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The semaphore stats_sem is used as mutex, convert it to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>