- 29 Sep, 2020 10 commits
-
-
Tony Nguyen authored
Add Jesse Brandeburg and myself; remove Jeff Kirsher. CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Vladimir Oltean says: ==================== More incorrect VCAP offsets for mscc_ocelot switch This small series fixes some wrong tc-flower action fields in the Seville and Felix DSA drivers. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Since the actions are packed together in the action RAM, an incorrect action width means that no action except the first one would behave correctly. The tc-flower offload has probably not been tested on this hardware since its introduction. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The port mask width was larger than the actual number of ports, and therefore, all fields following this one were also shifted by the number of excess bits. But the driver doesn't use the REW_OP, SMAC_REPLACE_ENA or ACL_ID bits from the action vector, so the bug was inconsequential. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Willy Liu authored
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns delays to TXC and RXC for TXD/RXD latching. These two pins can config via 4.7k-ohm resistor to 3.3V hw setting, but also config via software setting (extension page 0xa4 register 0x1c bit13 12 and 11). The configuration register definitions from table 13 official PHY datasheet: PHYAD[2:0] = PHY Address AN[1:0] = Auto-Negotiation Mode = Interface Mode Select RX Delay = RX Delay TX Delay = TX Delay SELRGV = RGMII/GMII Selection This table describes how to config these hw pins via external pull-high or pull- low resistor. It is a misunderstanding that mapping it as register bits below: 8:6 = PHY Address 5:4 = Auto-Negotiation 3 = Interface Mode Select 2 = RX Delay 1 = TX Delay 0 = SELRGV So I removed these descriptions above and add related settings as below: 14 = reserved 13 = force Tx RX Delay controlled by bit12 bit11 12 = Tx Delay 11 = Rx Delay 10:0 = Test && debug settings reserved by realtek Test && debug settings are not recommend to modify by default. Fixes: f81dadbc ("net: phy: realtek: Add rtl8211e rx/tx delays config") Signed-off-by: Willy Liu <willy.liu@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tonghao Zhang authored
Open vSwitch and Linux bridge will disable LRO of the interface when this interface added to them. Now when disable the LRO, the virtio-net csum is disable too. That drops the forwarding performance. Fixes: a02e8964 ("virtio-net: ethtool configurable LRO") Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Like all genl families ethtool_genl_family needs to not be a straight up constant, because it's modified/initialized by genl_register_family(). After init, however, it's only passed to genlmsg_put() & co. therefore we can mark it as __ro_after_init. Since genl_family structure contains function pointers mark this as a fix. Fixes: 2b4a8990 ("ethtool: introduce ethtool netlink interface") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
Validation flags are missing kdoc, add it. Fixes: ef6243ac ("genetlink: optionally validate strictly/dumps") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wilken Gottwalt authored
Adds the driver_info and usb ids of the AX88179 based MCT U3-A9003 USB 3.0 ethernet adapter. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wilken Gottwalt authored
Adds the missing .stop entry in the Belkin driver_info structure. Fixes: e20bd60b ("net: usb: asix88179_178a: Add support for the Belkin B2B128") Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 28 Sep, 2020 8 commits
-
-
Manivannan Sadhasivam authored
The rcu read locks are needed to avoid potential race condition while dereferencing radix tree from multiple threads. The issue was identified by syzbot. Below is the crash report: ============================= WARNING: suspicious RCU usage 5.7.0-syzkaller #0 Not tainted ----------------------------- include/linux/radix-tree.h:176 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 2 locks held by kworker/u4:1/21: #0: ffff88821b097938 ((wq_completion)qrtr_ns_handler){+.+.}-{0:0}, at: spin_unlock_irq include/linux/spinlock.h:403 [inline] #0: ffff88821b097938 ((wq_completion)qrtr_ns_handler){+.+.}-{0:0}, at: process_one_work+0x6df/0xfd0 kernel/workqueue.c:2241 #1: ffffc90000dd7d80 ((work_completion)(&qrtr_ns.work)){+.+.}-{0:0}, at: process_one_work+0x71e/0xfd0 kernel/workqueue.c:2243 stack backtrace: CPU: 0 PID: 21 Comm: kworker/u4:1 Not tainted 5.7.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: qrtr_ns_handler qrtr_ns_worker Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1e9/0x30e lib/dump_stack.c:118 radix_tree_deref_slot include/linux/radix-tree.h:176 [inline] ctrl_cmd_new_lookup net/qrtr/ns.c:558 [inline] qrtr_ns_worker+0x2aff/0x4500 net/qrtr/ns.c:674 process_one_work+0x76e/0xfd0 kernel/workqueue.c:2268 worker_thread+0xa7f/0x1450 kernel/workqueue.c:2414 kthread+0x353/0x380 kernel/kthread.c:268 Fixes: 0c2204a4 ("net: qrtr: Migrate nameservice to kernel from userspace") Reported-and-tested-by: syzbot+0f84f6eed90503da72fc@syzkaller.appspotmail.com Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Taehee Yoo says: ==================== net: core: fix a lockdep splat in the dev_addr_list. This patchset is to avoid lockdep splat. When a stacked interface graph is changed, netif_addr_lock() is called recursively and it internally calls spin_lock_nested(). The parameter of spin_lock_nested() is 'dev->lower_level', this is called subclass. The problem of 'dev->lower_level' is that while 'dev->lower_level' is being used as a subclass of spin_lock_nested(), its value can be changed. So, spin_lock_nested() would be called recursively with the same subclass value, the lockdep understands a deadlock. In order to avoid this, a new variable is needed and it is going to be used as a parameter of spin_lock_nested(). The first and second patch is a preparation patch for the third patch. In the third patch, the problem will be fixed. The first patch is to add __netdev_upper_dev_unlink(). An existed netdev_upper_dev_unlink() is renamed to __netdev_upper_dev_unlink(). and netdev_upper_dev_unlink() is added as an wrapper of this function. The second patch is to add the netdev_nested_priv structure. netdev_walk_all_{ upper | lower }_dev() pass both private functions and "data" pointer to handle their own things. At this point, the data pointer type is void *. In order to make it easier to expand common variables and functions, this new netdev_nested_priv structure is added. The third patch is to add a new variable 'nested_level' into the net_device structure. This variable will be used as a parameter of spin_lock_nested() of dev->addr_list_lock. Due to this variable, it can avoid lockdep splat. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
This patch is to add a new variable 'nested_level' into the net_device structure. This variable will be used as a parameter of spin_lock_nested() of dev->addr_list_lock. netif_addr_lock() can be called recursively so spin_lock_nested() is used instead of spin_lock() and dev->lower_level is used as a parameter of spin_lock_nested(). But, dev->lower_level value can be updated while it is being used. So, lockdep would warn a possible deadlock scenario. When a stacked interface is deleted, netif_{uc | mc}_sync() is called recursively. So, spin_lock_nested() is called recursively too. At this moment, the dev->lower_level variable is used as a parameter of it. dev->lower_level value is updated when interfaces are being unlinked/linked immediately. Thus, After unlinking, dev->lower_level shouldn't be a parameter of spin_lock_nested(). A (macvlan) | B (vlan) | C (bridge) | D (macvlan) | E (vlan) | F (bridge) A->lower_level : 6 B->lower_level : 5 C->lower_level : 4 D->lower_level : 3 E->lower_level : 2 F->lower_level : 1 When an interface 'A' is removed, it releases resources. At this moment, netif_addr_lock() would be called. Then, netdev_upper_dev_unlink() is called recursively. Then dev->lower_level is updated. There is no problem. But, when the bridge module is removed, 'C' and 'F' interfaces are removed at once. If 'F' is removed first, a lower_level value is like below. A->lower_level : 5 B->lower_level : 4 C->lower_level : 3 D->lower_level : 2 E->lower_level : 1 F->lower_level : 1 Then, 'C' is removed. at this moment, netif_addr_lock() is called recursively. The ordering is like this. C(3)->D(2)->E(1)->F(1) At this moment, the lower_level value of 'E' and 'F' are the same. So, lockdep warns a possible deadlock scenario. In order to avoid this problem, a new variable 'nested_level' is added. This value is the same as dev->lower_level - 1. But this value is updated in rtnl_unlock(). So, this variable can be used as a parameter of spin_lock_nested() safely in the rtnl context. Test commands: ip link add br0 type bridge vlan_filtering 1 ip link add vlan1 link br0 type vlan id 10 ip link add macvlan2 link vlan1 type macvlan ip link add br3 type bridge vlan_filtering 1 ip link set macvlan2 master br3 ip link add vlan4 link br3 type vlan id 10 ip link add macvlan5 link vlan4 type macvlan ip link add br6 type bridge vlan_filtering 1 ip link set macvlan5 master br6 ip link add vlan7 link br6 type vlan id 10 ip link add macvlan8 link vlan7 type macvlan ip link set br0 up ip link set vlan1 up ip link set macvlan2 up ip link set br3 up ip link set vlan4 up ip link set macvlan5 up ip link set br6 up ip link set vlan7 up ip link set macvlan8 up modprobe -rv bridge Splat looks like: [ 36.057436][ T744] WARNING: possible recursive locking detected [ 36.058848][ T744] 5.9.0-rc6+ #728 Not tainted [ 36.059959][ T744] -------------------------------------------- [ 36.061391][ T744] ip/744 is trying to acquire lock: [ 36.062590][ T744] ffff8c4767509280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_set_rx_mode+0x19/0x30 [ 36.064922][ T744] [ 36.064922][ T744] but task is already holding lock: [ 36.066626][ T744] ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60 [ 36.068851][ T744] [ 36.068851][ T744] other info that might help us debug this: [ 36.070731][ T744] Possible unsafe locking scenario: [ 36.070731][ T744] [ 36.072497][ T744] CPU0 [ 36.073238][ T744] ---- [ 36.074007][ T744] lock(&vlan_netdev_addr_lock_key); [ 36.075290][ T744] lock(&vlan_netdev_addr_lock_key); [ 36.076590][ T744] [ 36.076590][ T744] *** DEADLOCK *** [ 36.076590][ T744] [ 36.078515][ T744] May be due to missing lock nesting notation [ 36.078515][ T744] [ 36.080491][ T744] 3 locks held by ip/744: [ 36.081471][ T744] #0: ffffffff98571df0 (rtnl_mutex){+.+.}-{3:3}, at: rtnetlink_rcv_msg+0x236/0x490 [ 36.083614][ T744] #1: ffff8c4767769280 (&vlan_netdev_addr_lock_key){+...}-{2:2}, at: dev_uc_add+0x1e/0x60 [ 36.085942][ T744] #2: ffff8c476c8da280 (&bridge_netdev_addr_lock_key/4){+...}-{2:2}, at: dev_uc_sync+0x39/0x80 [ 36.088400][ T744] [ 36.088400][ T744] stack backtrace: [ 36.089772][ T744] CPU: 6 PID: 744 Comm: ip Not tainted 5.9.0-rc6+ #728 [ 36.091364][ T744] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 [ 36.093630][ T744] Call Trace: [ 36.094416][ T744] dump_stack+0x77/0x9b [ 36.095385][ T744] __lock_acquire+0xbc3/0x1f40 [ 36.096522][ T744] lock_acquire+0xb4/0x3b0 [ 36.097540][ T744] ? dev_set_rx_mode+0x19/0x30 [ 36.098657][ T744] ? rtmsg_ifinfo+0x1f/0x30 [ 36.099711][ T744] ? __dev_notify_flags+0xa5/0xf0 [ 36.100874][ T744] ? rtnl_is_locked+0x11/0x20 [ 36.101967][ T744] ? __dev_set_promiscuity+0x7b/0x1a0 [ 36.103230][ T744] _raw_spin_lock_bh+0x38/0x70 [ 36.104348][ T744] ? dev_set_rx_mode+0x19/0x30 [ 36.105461][ T744] dev_set_rx_mode+0x19/0x30 [ 36.106532][ T744] dev_set_promiscuity+0x36/0x50 [ 36.107692][ T744] __dev_set_promiscuity+0x123/0x1a0 [ 36.108929][ T744] dev_set_promiscuity+0x1e/0x50 [ 36.110093][ T744] br_port_set_promisc+0x1f/0x40 [bridge] [ 36.111415][ T744] br_manage_promisc+0x8b/0xe0 [bridge] [ 36.112728][ T744] __dev_set_promiscuity+0x123/0x1a0 [ 36.113967][ T744] ? __hw_addr_sync_one+0x23/0x50 [ 36.115135][ T744] __dev_set_rx_mode+0x68/0x90 [ 36.116249][ T744] dev_uc_sync+0x70/0x80 [ 36.117244][ T744] dev_uc_add+0x50/0x60 [ 36.118223][ T744] macvlan_open+0x18e/0x1f0 [macvlan] [ 36.119470][ T744] __dev_open+0xd6/0x170 [ 36.120470][ T744] __dev_change_flags+0x181/0x1d0 [ 36.121644][ T744] dev_change_flags+0x23/0x60 [ 36.122741][ T744] do_setlink+0x30a/0x11e0 [ 36.123778][ T744] ? __lock_acquire+0x92c/0x1f40 [ 36.124929][ T744] ? __nla_validate_parse.part.6+0x45/0x8e0 [ 36.126309][ T744] ? __lock_acquire+0x92c/0x1f40 [ 36.127457][ T744] __rtnl_newlink+0x546/0x8e0 [ 36.128560][ T744] ? lock_acquire+0xb4/0x3b0 [ 36.129623][ T744] ? deactivate_slab.isra.85+0x6a1/0x850 [ 36.130946][ T744] ? __lock_acquire+0x92c/0x1f40 [ 36.132102][ T744] ? lock_acquire+0xb4/0x3b0 [ 36.133176][ T744] ? is_bpf_text_address+0x5/0xe0 [ 36.134364][ T744] ? rtnl_newlink+0x2e/0x70 [ 36.135445][ T744] ? rcu_read_lock_sched_held+0x32/0x60 [ 36.136771][ T744] ? kmem_cache_alloc_trace+0x2d8/0x380 [ 36.138070][ T744] ? rtnl_newlink+0x2e/0x70 [ 36.139164][ T744] rtnl_newlink+0x47/0x70 [ ... ] Fixes: 845e0ebb ("net: change addr_list_lock back to static key") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
Functions related to nested interface infrastructure such as netdev_walk_all_{ upper | lower }_dev() pass both private functions and "data" pointer to handle their own things. At this point, the data pointer type is void *. In order to make it easier to expand common variables and functions, this new netdev_nested_priv structure is added. In the following patch, a new member variable will be added into this struct to fix the lockdep issue. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
The netdev_upper_dev_unlink() has to work differently according to flags. This idea is the same with __netdev_upper_dev_link(). In the following patches, new flags will be added. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Cong Wang authored
All TC actions call tcf_action_check_ctrlact() to validate goto chain, so this check in tcf_action_init_1() is actually redundant. Remove it to save troubles of leaking memory. Fixes: e49d8c22 ("net_sched: defer tcf_idr_insert() in tcf_action_init_1()") Reported-by: Vlad Buslov <vladbu@mellanox.com> Suggested-by: Davide Caratti <dcaratti@redhat.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
When a user-space software manages fdb entries externally it should set the ext_learn flag which marks the fdb entry as externally managed and avoids expiring it (they're treated as static fdbs). Unfortunately on events where fdb entries are flushed (STP down, netlink fdb flush etc) these fdbs are also deleted automatically by the bridge. That in turn causes trouble for the managing user-space software (e.g. in MLAG setups we lose remote fdb entries on port flaps). These entries are completely externally managed so we should avoid automatically deleting them, the only exception are offloaded entries (i.e. BR_FDB_ADDED_BY_EXT_LEARN + BR_FDB_OFFLOADED). They are flushed as before. Fixes: eb100e0e ("net: bridge: allow to add externally learned entries from user-space") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsecDavid S. Miller authored
Steffen Klassert says: ==================== pull request (net): ipsec 2020-09-28 1) Fix a build warning in ip_vti if CONFIG_IPV6 is not set. From YueHaibing. 2) Restore IPCB on espintcp before handing the packet to xfrm as the information there is still needed. From Sabrina Dubroca. 3) Fix pmtu updating for xfrm interfaces. From Sabrina Dubroca. 4) Some xfrm state information was not cloned with xfrm_do_migrate. Fixes to clone the full xfrm state, from Antony Antony. 5) Use the correct address family in xfrm_state_find. The struct flowi must always be interpreted along with the original address family. This got lost over the years. Fix from Herbert Xu. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 27 Sep, 2020 4 commits
-
-
Heiner Kallweit authored
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver. Fixes: a7a92cf8 ("r8169: sync PCIe PHY init with vendor driver 8.047.01") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Marian-Cristian Rotariu authored
Document RZ/G2H (R8A774E1) SoC bindings. Signed-off-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
If mlxsw_sp_acl_tcam_group_id_get() fails, the mutex initialized earlier is not destroyed. Fix this by initializing the mutex after calling the function. This is symmetric to mlxsw_sp_acl_tcam_group_del(). Fixes: 5ec2ee28 ("mlxsw: spectrum_acl: Introduce a mutex to guard region list updates") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER. Fixes this build error: ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe': drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size' Fixes: 379d7ac7 ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: netdev@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 26 Sep, 2020 7 commits
-
-
Igor Russkikh authored
Driver subfolder files refer parent folder includes in an absolute manner. Makefile contains a -I for this, but apparently that does not work if object tree is separated. Adding srctree to fix that. Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ioana Ciornei authored
When adding the support for TBF offload, the improper command version was added even though the command format is for the V2 of dpni_set_tx_shaping(). This does not affect the functionality of TBF since the only change between these two versions is the addition of the exceeded parameters which are not used in TBF. Still, fix the bug so that we keep things in sync. Fixes: 39344a89 ("dpaa2-eth: add API for Tx shaping") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wilken Gottwalt authored
Adds the driver_info and usb ids of the AX88179 based Toshiba USB 3.0 ethernet adapter. Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Eric Dumazet says: ==================== bonding/team: basic dev->needed_headroom support Both bonding and team drivers support non-ethernet devices, but missed proper dev->needed_headroom initializations. syzbot found a crash caused by bonding, I mirrored the fix in team as well. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Some devices set needed_headroom. If we ignore it, we might end up crashing in various skb_push() for example in ipgre_header() since some layers assume enough headroom has been reserved. Fixes: 1d76efe1 ("team: add support for non-ethernet devices") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
syzbot managed to crash a host by creating a bond with a GRE device. For non Ethernet device, bonding calls bond_setup_by_slave() instead of ether_setup(), and unfortunately dev->needed_headroom was not copied from the new added member. [ 171.243095] skbuff: skb_under_panic: text:ffffffffa184b9ea len:116 put:20 head:ffff883f84012dc0 data:ffff883f84012dbc tail:0x70 end:0xd00 dev:bond0 [ 171.243111] ------------[ cut here ]------------ [ 171.243112] kernel BUG at net/core/skbuff.c:112! [ 171.243117] invalid opcode: 0000 [#1] SMP KASAN PTI [ 171.243469] gsmi: Log Shutdown Reason 0x03 [ 171.243505] Call Trace: [ 171.243506] <IRQ> [ 171.243512] [<ffffffffa171be59>] skb_push+0x49/0x50 [ 171.243516] [<ffffffffa184b9ea>] ipgre_header+0x2a/0xf0 [ 171.243520] [<ffffffffa17452d7>] neigh_connected_output+0xb7/0x100 [ 171.243524] [<ffffffffa186f1d3>] ip6_finish_output2+0x383/0x490 [ 171.243528] [<ffffffffa186ede2>] __ip6_finish_output+0xa2/0x110 [ 171.243531] [<ffffffffa186acbc>] ip6_finish_output+0x2c/0xa0 [ 171.243534] [<ffffffffa186abe9>] ip6_output+0x69/0x110 [ 171.243537] [<ffffffffa186ac90>] ? ip6_output+0x110/0x110 [ 171.243541] [<ffffffffa189d952>] mld_sendpack+0x1b2/0x2d0 [ 171.243544] [<ffffffffa189d290>] ? mld_send_report+0xf0/0xf0 [ 171.243548] [<ffffffffa189c797>] mld_ifc_timer_expire+0x2d7/0x3b0 [ 171.243551] [<ffffffffa189c4c0>] ? mld_gq_timer_expire+0x50/0x50 [ 171.243556] [<ffffffffa0fea270>] call_timer_fn+0x30/0x130 [ 171.243559] [<ffffffffa0fea17c>] expire_timers+0x4c/0x110 [ 171.243563] [<ffffffffa0fea0e3>] __run_timers+0x213/0x260 [ 171.243566] [<ffffffffa0fecb7d>] ? ktime_get+0x3d/0xa0 [ 171.243570] [<ffffffffa0ff9c4e>] ? clockevents_program_event+0x7e/0xe0 [ 171.243574] [<ffffffffa0f7e5d5>] ? sched_clock_cpu+0x15/0x190 [ 171.243577] [<ffffffffa0fe973d>] run_timer_softirq+0x1d/0x40 [ 171.243581] [<ffffffffa1c00152>] __do_softirq+0x152/0x2f0 [ 171.243585] [<ffffffffa0f44e1f>] irq_exit+0x9f/0xb0 [ 171.243588] [<ffffffffa1a02e1d>] smp_apic_timer_interrupt+0xfd/0x1a0 [ 171.243591] [<ffffffffa1a01ea6>] apic_timer_interrupt+0x86/0x90 Fixes: f5184d26 ("net: Allow netdevices to specify needed head/tailroom") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 25 Sep, 2020 11 commits
-
-
Ivan Khoronzhuk authored
To start also "phy state machine", with UP state as it should be, the phy_start() has to be used, in another case machine even is not triggered. After this change negotiation is supposed to be triggered by SM workqueue. It's not correct usage, but it appears after the following patch, so add it as a fix. Fixes: 74a992b3 ("net: phy: add phy_check_link_status") Signed-off-by: Ivan Khoronzhuk <ikhoronz@cisco.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wong Vee Khee authored
While unloading the dwmac-intel driver, clk_disable_unprepare() is being called twice in stmmac_dvr_remove() and intel_eth_pci_remove(). This causes kernel panic on the second call. Removing the second call of clk_disable_unprepare() in intel_eth_pci_remove(). Fixes: 09f012e6 ("stmmac: intel: Fix clock handling on error and remove paths") Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ronak Doshi authored
Commit dacce2be ("vmxnet3: add geneve and vxlan tunnel offload support") added support for encapsulation offload. However, the inner offload capability is to be restrictued to UDP tunnels. This patch fixes the issue for non-udp tunnels by adding features check capability and filtering appropriate features for non-udp tunnels. Fixes: dacce2be ("vmxnet3: add geneve and vxlan tunnel offload support") Signed-off-by: Ronak Doshi <doshir@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2020-09-25 This series contains updates to the iavf and ice driver. Sylwester fixes a crash with iavf resume due to getting the wrong pointers. Ani fixes a call trace in ice resume by calling pci_save_state(). Jakes fixes memory leaks in case of register_netdev() failure or ice_cfg_vsi_lan() failure for the ice driver. v2: Rebased; no other changes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'wireless-drivers-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for v5.9 Second, and last, set of fixes for v5.9. Only one important regression fix for mt76. mt76 * fix a regression in aggregation which appeared after mac80211 changes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jacob Keller authored
During ice_vsi_setup, if ice_cfg_vsi_lan fails, it does not properly release memory associated with the VSI rings. If we had used devres allocations for the rings, this would be ok. However, we use kzalloc and kfree_rcu for these ring structures. Using the correct label to cleanup the rings during ice_vsi_setup highlights an issue in the ice_vsi_clear_rings function: it can leave behind stale ring pointers in the q_vectors structure. When releasing rings, we must also ensure that no q_vector associated with the VSI will point to this ring again. To resolve this, loop over all q_vectors and release their ring mapping. Because we are about to free all rings, no q_vector should remain pointing to any of the rings in this VSI. Fixes: 5513b920 ("ice: Update Tx scheduler tree for VSI multi-Tx queue support") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Jacob Keller authored
The ice_setup_pf_sw function can cause a memory leak if register_netdev fails, due to accidentally failing to free the VSI rings. Fix the memory leak by using ice_vsi_release, ensuring we actually go through the full teardown process. This should be safe even if the netdevice is not registered because we will have set the netdev pointer to NULL, ensuring ice_vsi_release won't call unregister_netdev. An alternative fix would be moving management of the PF VSI netdev into the main VSI setup code. This is complicated and likely requires significant refactor in how we manage VSIs Fixes: 3a858ba3 ("ice: Add support for VSI allocation and deallocation") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Anirudh Venkataramanan authored
It appears that the ice_suspend flow is missing a call to pci_save_state and this is triggering the message "State of device not saved by ice_suspend" and a call trace. Fix it. Fixes: 769c500d ("ice: Add advanced power mgmt for WoL") Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Sylwester Dziedziuch authored
When calling iavf_resume there was a crash because wrong function was used to get iavf_adapter and net_device pointers. Changed how iavf_resume is getting iavf_adapter and net_device pointers from pci_dev. Fixes: 5eae00c5 ("i40evf: main driver core") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Herbert Xu authored
The struct flowi must never be interpreted by itself as its size depends on the address family. Therefore it must always be grouped with its original family value. In this particular instance, the original family value is lost in the function xfrm_state_find. Therefore we get a bogus read when it's coupled with the wrong family which would occur with inter- family xfrm states. This patch fixes it by keeping the original family value. Note that the same bug could potentially occur in LSM through the xfrm_state_pol_flow_match hook. I checked the current code there and it seems to be safe for now as only secid is used which is part of struct flowi_common. But that API should be changed so that so that we don't get new bugs in the future. We could do that by replacing fl with just secid or adding a family field. Reported-by: syzbot+577fbac3145a6eb2e7a5@syzkaller.appspotmail.com Fixes: 48b8d783 ("[XFRM]: State selection update to use inner...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
-
Priyaranjan Jha authored
Currently, we use length of DSACKed range to compute number of delivered packets. And if sequence range in DSACK is corrupted, we can get bogus dsacked/acked count, and bogus cwnd. This patch put bounds on DSACKed range to skip update of data delivery and spurious retransmission information, if the DSACK is unlikely caused by sender's action: - DSACKed range shouldn't be greater than maximum advertised rwnd. - Total no. of DSACKed segments shouldn't be greater than total no. of retransmitted segs. Unlike spurious retransmits, network duplicates or corrupted DSACKs shouldn't be counted as delivery. Signed-off-by: Priyaranjan Jha <priyarjha@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-