- 02 Jun, 2010 40 commits
-
-
Bruno Randolf authored
It's our "private driver data"... It's used more often and hw is the mac80211 part. This makes more sense with the next (sysfs) patch. Signed-off-by:
Bruno Randolf <br1@einfach.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Bruno Randolf authored
The old code logically did not make sense and seems to have been confused by the fact that we could have newer EEPROMs on older hardware. In any case the spur mitigation filter was set if the srev was >= AR5K_SREV_AR5424. Spur info is available only from EEPROM versions bigger than 5.3 but but the EEPOM routines will use static values for older versions, so that should be o.k. Signed-off-by:
-
Bruno Randolf authored
Now that we have ftrace, it is not needed any more. Signed-off-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
-
Bruno Randolf authored
Since NF calibration interferes with TX and RX and also has been the cause of other problems (when it's run concurrently with ath5k_reset) we want to run it less often - every 60 seconds for now. Signed-off-by:
-
Bruno Randolf authored
As far as we know, only NF calibration interferes with RX/TX so we can leave the queues enabled for the other calibrations. BTW: Stopping the queues is not enough for avoiding transmissions, since there might be packets in the queue + beacons are also sent regularly! But i leave it like this until we have a better solution (stopping TX DMA?). Signed-off-by:
-
Bruno Randolf authored
Seperate noise floor calibration from other PHY calibration and move it to the tasklet. This is the first step to more separation of different calibrations. Also move out ath5k_hw_request_rfgain_probe(ah) so we have one clean function for I/Q calibration on 5111x parts. Signed-off-by:
-
Bruno Randolf authored
Initialize calibration timers on reset, since otherwise they might be in the future and the calibration tasklet might not be scheduled for a long time. Signed-off-by:
-
Jussi Kivilinna authored
Buffer size for get_association_info was limited to WEXT event size. Since association info no longer is sent through WEXT, this limit is not needed. Code also did not check if data get truncated, memory outside buffer might be addressed. Fix all these. Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Rx should not be disabed/disabled when hw supports auto sleeping. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Add missing code to handle nullfunc frame completion in ath_tx_edma_tasklet(). Signed-off-by:
-
Walter Goldens authored
Signed-off-by:
Walter Goldens <goldenstranger@yahoo.com> Signed-off-by:
-
Helmut Schaa authored
Don't refuse HT20 channels on devices that don't support HT40. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Use BSS_CHANGED_HT to handle HT parameter changes. The rate information on the target has to be updated to handle changes in HT configuration. Signed-off-by:
-
Sujith authored
This patch removes a large chunk of code dealing with rate management within the driver and simplifying things by removing the hacky method of calculating HT changes. A subsequent patch would fix this by just using BSS_CHANGED_HT from mac80211. Signed-off-by:
-
Sujith authored
Update from internal systems engineering team. Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Samuel Ortiz <sameo@linux.intel.com> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Kalle Valo <kvalo@adurom.com> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Dan Carpenter authored
Changed -EINVAL to -EFAULT if copy_to_user() failed. Changed 0 to -ENOMEM if allocations failed. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
-
Dan Carpenter authored
The snprintf() function returns the number of bytes that *would* have been written (not counting the NULL terminator) and that can potentally be more than the size of the buffer. In this patch if there were one liners where string clearly fits into the buffer, then I changed snprintf to sprintf(). It's confusing to use the return value of snprintf() as a limitter without verifying that it's smaller than size. This is what initially caught my attention here. If we use the return value of sprintf() instead future code auditors will assume we've verified that it fits already. Also I did find some places where it made sense to use the return value after we've verified that it is smaller than the buffer size. Finally the read_file_rcstat() function added an explicit NULL terminator before calling snprintf(). That's unnecessary because snprintf() will add the null terminator automatically. Signed-off-by:
-
Ming Lei authored
For edma, we should use DMA_BIDIRECTIONAL, or else use DMA_FROM_DEVICE. Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Signed-off-by:
-
Amitkumar Karwar authored
In suspend() host sleep is activated using already configured host sleep parameters through wol command, and in resume() host sleep is cancelled. Earlier priv->fw_ready flag used to reset and set in suspend and resume handler respectively. Since after suspend only host goes into sleep state and firmware is always ready, those changes in flag state are removed. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Juuso Oikarinen authored
This patch adds support for NVS files with 5GHz band parameters. The change is done in a backward compatible manner - if 11a is not enabled in the driver, the driver will allow also old NVS files to be loaded. Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
This patch updates the handling of the NVS file INI-section, trying to make it slightly more generic, and exposing the parameters being set. This is done in preparation for 5GHz parameters. Signed-off-by:
-
Sujith authored
This is the maximum supported by the firmware. Signed-off-by:
-
Sujith authored
There is no need to determine the HW queue for each packet that is transmitted. The endpoint can be chosen directly based on the queue type that mac80211 sends down. Signed-off-by:
-
Sujith authored
This patch initializes the beacon and CAB HW queues when the driver is loaded. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
This patch enables short GI rx at all rates and tx at mcs15 for 20 Mhz channel width also. Signed-off-by:
-
Julia Lawall authored
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by:
-
Luis R. Rodriguez authored
This enables the baseband watchdog events for the AR9003 family on ath9k. Upon an a baseband watchdog interrupt we reset the hardware, this should address corner case conditions where normal operation can stall. Enable ATH_DBG_RESET to be able to review details of the bb watchdog interrupt once it happens. If you're curious how often this happens just grep the debugfs interrupt file. Cc: Sam Ng <sam.ng@atheros.com> Cc: Paul Shaw <paul.shaw@atheros.com> Cc: Don Breslin <don.breslin@atheros.com> Cc: Cliff Holden <cliff.holden@atheros.com Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com Signed-off-by:
-
