usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.

To program it driver uses i2c-bus phandle (added in commit '02be19e9
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.

Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.

Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.

The byte sequence is as follows:
Slave addr: 0x2d           00 00 05 00 01 41 1D 08
Slave addr: 0x2d           99 37 00
Slave addr: 0x2d           AA 56 00

Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1725732196-70975-3-git-send-email-radhey.shyam.pandey@amd.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.

i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed

Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1725732196-70975-2-git-send-email-radhey.shyam.pandey@amd.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.

Release the gadget clocks before handling the USB role update.

Fixes: 0112b7ce ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")
Cc: stable@vger.kernel.org
Signed-off-by: Tomas Marek <tomas.marek@elrest.cz>
Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.czSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.

Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.

Fixes: 3d829045 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB9538E8CA7A2096AAF6A3718FDD9E2@PH7PR07MB9538.namprd07.prod.outlook.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.

When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240905065328.7116-1-parth105105@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed coding style issue: unsigned to unsigned int.
Signed-off-by: Andreas Kühn <andreas.kuehn@diekuehnen.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240903132535.15554-1-andreas.kuehn@diekuehnen.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace open coded device_property_match_property_string().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240903183136.3641770-1-andriy.shevchenko@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The syzbot reported a kernel-usb-infoleak in usbtmc_write,
we need to clear the structure before filling fields.

Fixes: 4ddc645f ("usb: usbtmc: Add ioctl for vendor specific write")
Reported-and-tested-by: syzbot+9d34f80f841e948c3fdb@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=9d34f80f841e948c3fdbSigned-off-by: Edward Adam Davis <eadavis@qq.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/tencent_9649AA6EC56EDECCA8A7D106C792D1C66B06@qq.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stephen Rothwell reported htmldocs warning when merging usb tree:

Documentation/filesystems/9p.rst:99: ERROR: Unexpected indentation.

That's because Sphinx tries rendering p9_fwd.py output as a grid table
instead.

Wrap shell commands in "USBG Example" section in literal code blocks
to fix above warning and to be in line with rest of commands in the doc.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20240905184059.0f30ff9a@canb.auug.org.au/
Fixes: 673f0c3f ("tools: usb: p9_fwd: add usb gadget packet forwarder script")
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240908113423.158352-1-bagasdotme@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The combination of dev_err() and the returned error code could be
replaced by dev_err_probe() in driver's probe function. Let's,
converting to dev_err_probe() to make code more simple.
Signed-off-by: Lin Ruifeng <linruifeng4@huawei.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20240907081351.19879-1-linruifeng4@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial device id for 6.12-rc1

Here's a new pl2303 device id.

This one has been in linux-next with no reported issues.

* tag 'usb-serial-6.12-rc1-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: pl2303: add device id for Macrosilicon MS3020

Merge tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for 6.12-rc1

Here are the USB-serial updates for 6.12-rc1, including:

 - fix kobil_sct initial terminal settings
 - set driver owner when registering drivers

All have been in linux-next with no reported issues.

* tag 'usb-serial-6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: kobil_sct: restore initial terminal settings
  USB: serial: drop driver owner initialization
  USB: serial: set driver owner when registering drivers

Merge tag 'thunderbolt-for-v6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next

Mika writes:

thunderbolt: Changes for v6.12 merge window

This includes following USB4/Thunderbolt changes for the v6.12 merge
window:

  - Improvements for software receiver lane margining
  - Enable support for optional voltage offset range for receiver lane
    margining.

All these have been in linux-next with no reported issues.

* tag 'thunderbolt-for-v6.12-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
  thunderbolt: Improve software receiver lane margining
  thunderbolt: Add optional voltage offset range for receiver lane margining
  thunderbolt: Consolidate margining parameters into a structure
  thunderbolt: Add missing usb4_port_sb_read() to usb4_port_sw_margin()

We need the USB fixes in here as well, and this also resolves the merge
conflict in:
	drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull timer fixes from Borislav Petkov:

 - Remove percpu irq related code in the timer-of initialization routine
   as it is broken but also unused (Daniel Lezcano)

 - Fix return -ETIME when delta exceeds INT_MAX and the next event not
   taking effect sometimes (Jacky Bai)

* tag 'timers_urgent_for_v6.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/imx-tpm: Fix next event not taking effect sometime
  clocksource/drivers/imx-tpm: Fix return -ETIME when delta exceeds INT_MAX
  clocksource/drivers/timer-of: Remove percpu irq related code

Pull perf fixes from Borislav Petkov:

 - Fix perf's AUX buffer serialization

 - Prevent uninitialized struct members in perf's uprobes handling

* tag 'perf_urgent_for_v6.11_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/aux: Fix AUX buffer serialization
  uprobes: Use kzalloc to allocate xol area

Pull char/misc driver fixes from Greg KH:
 "Here are some small char/misc/other driver fixes for 6.11-rc7. It's
  nothing huge, just a bunch of small fixes of reported problems,
  including:

   - lots of tiny iio driver fixes

   - nvmem driver fixex

   - binder UAF bugfix

   - uio driver crash fix

   - other small fixes

  All of these have been in linux-next this week with no reported
  problems"

* tag 'char-misc-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
  VMCI: Fix use-after-free when removing resource in vmci_resource_remove()
  Drivers: hv: vmbus: Fix rescind handling in uio_hv_generic
  uio_hv_generic: Fix kernel NULL pointer dereference in hv_uio_rescind
  misc: keba: Fix sysfs group creation
  dt-bindings: nvmem: Use soc-nvmem node name instead of nvmem
  nvmem: Fix return type of devm_nvmem_device_get() in kerneldoc
  nvmem: u-boot-env: error if NVMEM device is too small
  misc: fastrpc: Fix double free of 'buf' in error path
  binder: fix UAF caused by offsets overwrite
  iio: imu: inv_mpu6050: fix interrupt status read for old buggy chips
  iio: adc: ad7173: fix GPIO device info
  iio: adc: ad7124: fix DT configuration parsing
  iio: adc: ad_sigma_delta: fix irq_flags on irq request
  iio: adc: ads1119: Fix IRQ flags
  iio: fix scale application in iio_convert_raw_to_processed_unlocked
  iio: adc: ad7124: fix config comparison
  iio: adc: ad7124: fix chip ID mismatch
  iio: adc: ad7173: Fix incorrect compatible string
  iio: buffer-dmaengine: fix releasing dma channel on error
  iio: adc: ad7606: remove frstdata check for serial mode
  ...

Pull USB fixes from Greg KH:
 "Here are a handful of small USB fixes for 6.11-rc7. Included in here
  are:

   - dwc3 driver fixes for two reported problems

   - two typec ucsi driver fixes

   - cdns2 controller reset fix

  All of these have been in linux-next this week with no reported
  problems"

* tag 'usb-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: ucsi: Fix cable registration
  usb: typec: ucsi: Fix the partner PD revision
  usb: cdns2: Fix controller reset issue
  usb: dwc3: core: update LC timer as per USB Spec V3.2
  usb: dwc3: Avoid waking up gadget during startxfer

Pull clk fixes from Stephen Boyd:
 "A pile of Qualcomm clk driver fixes with two main themes: the alpha
  PLL driver and shared RCGs, and one fix for the Starfive JH7110 SoC.

   - The Alpha PLL clk_ops had multiple problems around setting rates.

     There are a handful of patches here that fix masks and skip
     enabling the clk from set_rate() when the PLL is disabled. The PLLs
     are crucial to operation of the system as almost all frequencies in
     the system are derived from them.

   - Parking shared RCGs at a slow always on clk at registration time
     breaks stuff.

     USB host mode can't handle such a slow frequency and the serial
     console gets all garbled when the UART clk is handed over to the
     kernel. There's a few patches that don't use the shared clk_ops for
     the UART clks and another one to skip parking the USB clk at
     registration time.

   - The Starfive PLL driver used for the CPU was busted causing cpufreq
     to fail because the clk didn't change to a safe parent during
     set_rate().

     The fix is to register a notifier and switch to a safe parent so
     the PLL can change rate in a glitch free manner"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: gcc-sc8280xp: don't use parking clk_ops for QUPs
  clk: starfive: jh7110-sys: Add notifier for PLL0 clock
  clk: qcom: gcc-sm8650: Don't use shared clk_ops for QUPs
  clk: qcom: gcc-sm8550: Don't park the USB RCG at registration time
  clk: qcom: gcc-sm8550: Don't use parking clk_ops for QUPs
  clk: qcom: gcc-x1e80100: Don't use parking clk_ops for QUPs
  clk: qcom: ipq9574: Update the alpha PLL type for GPLLs
  clk: qcom: gcc-x1e80100: Fix USB 0 and 1 PHY GDSC pwrsts flags
  clk: qcom: clk-alpha-pll: Update set_rate for Zonda PLL
  clk: qcom: clk-alpha-pll: Fix zonda set_rate failure when PLL is disabled
  clk: qcom: clk-alpha-pll: Fix the trion pll postdiv set rate API
  clk: qcom: clk-alpha-pll: Fix the pll post div mask

Pull SCSI fix from James Bottomley:
 "Single ufs driver fix quirking around another device spec violation"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: ufs-mediatek: Add UFSHCD_QUIRK_BROKEN_LSDBS_CAP

Pull pin control fix from Linus Walleij:
 "A single fix for Qualcomm laptops that are affected by
  missing wakeup IRQs"

* tag 'pinctrl-v6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: qcom: x1e80100: Bypass PDC wakeup parent for now

Merge tag 'linux_kselftest-kunit-fixes-6.11-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

PullKUnit fix from Shuah Khan:
 "Fix to a missing function parameter warning found during documentation
  build in linux-next"

* tag 'linux_kselftest-kunit-fixes-6.11-rc7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: Fix missing kerneldoc comment

Pull pci fixes from Bjorn Helgaas:

 - Unregister platform devices for child nodes when stopping a PCI
   device, even if the PCI core has already cleared the OF_POPULATED bit
   and of_platform_depopulate() doesn't do anything (Bartosz
   Golaszewski)

 - Rescan the bus from a separate thread so we don't deadlock when
   triggering rescan from sysfs (Bartosz Golaszewski)

* tag 'pci-v6.11-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
  PCI/pwrctl: Rescan bus on a separate thread
  PCI: Don't rely on of_platform_depopulate() for reused OF-nodes

Pull smb client fixes from Steve French:

 - fix potential mount hang

 - fix retry problem in two types of compound operations

 - important netfs integration fix in SMB1 read paths

 - fix potential uninitialized zero point of inode

 - minor patch to improve debugging for potential crediting problems

* tag 'v6.11-rc6-cifs-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  netfs, cifs: Improve some debugging bits
  cifs: Fix SMB1 readv/writev callback in the same way as SMB2/3
  cifs: Fix zero_point init on inode initialisation
  smb: client: fix double put of @cfile in smb2_set_path_size()
  smb: client: fix double put of @cfile in smb2_rename_path()
  smb: client: fix hang in wait_for_response() for negproto

clang warns on this because it has an unannotated fall-through between
cases:

   arch/x86/kvm/x86.c:4819:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]

and while we could annotate it as a fallthrough, the proper fix is to
just add the break for this case, instead of falling through to the
default case and the break there.

gcc also has that warning, but it looks like gcc only warns for the
cases where they fall through to "real code", rather than to just a
break.  Odd.

Fixes: d30d9ee9 ("KVM: x86: Only advertise KVM_CAP_READONLY_MEM when supported by VM")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Tom Dohrmann <erbse.13@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arm64 fix from Catalin Marinas:
 "Fix the arm64 usage of ftrace_graph_ret_addr() to pass the
  &state->graph_idx pointer instead of NULL, otherwise this function
  just returns early"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: stacktrace: fix the usage of ftrace_graph_ret_addr()

Pull RISC-V fixes from Palmer Dabbelt:

 - A revert for the mmap() change that ties the allocation range to the
   hint adress, as what we tried to do ended up regressing on other
   userspace workloads.

 - A fix to avoid a kernel memory leak when emulating misaligned
   accesses from userspace.

 - A Kconfig fix for toolchain vector detection, which now correctly
   detects vector support on toolchains where the V extension depends on
   the M extension.

 - A fix to avoid failing the linear mapping bootmem bounds check on
   NOMMU systems.

 - A fix for early alternatives on relocatable kernels.

* tag 'riscv-for-linus-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fix RISCV_ALTERNATIVE_EARLY
  riscv: Do not restrict memory size because of linear mapping on nommu
  riscv: Fix toolchain vector detection
  riscv: misaligned: Restrict user access to kernel memory
  riscv: mm: Do not restrict mmap address based on hint
  riscv: selftests: Remove mmap hint address checks
  Revert "RISC-V: mm: Document mmap changes"

Pull powerpc fixes from Michael Ellerman:

 - Fix a deadlock in the powerpc qspinlock MCS queue logic

 - Fix the return type of pgd_val() to not truncate 64-bit PTEs on 85xx

 - Allow the check for dynamic relocations in the VDSO to work correctly

 - Make mmu_pte_psize static to fix a build error

Thanks to Christophe Leroy, Nysal Jan K.A., Nicholas Piggin, Geetika
Moolchandani, Jijo Varghese, and Vaishnavi Bhat.

* tag 'powerpc-6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/qspinlock: Fix deadlock in MCS queue
  powerpc/mm: Fix return type of pgd_val()
  powerpc/vdso: Don't discard rela sections
  powerpc/64e: Define mmu_pte_psize static

Pull x86 kvm fixes from Paolo Bonzini:
 "Many small fixes that accumulated while I was on vacation...

   - Fixup missed comments from the REMOVED_SPTE => FROZEN_SPTE rename

   - Ensure a root is successfully loaded when pre-faulting SPTEs

   - Grab kvm->srcu when handling KVM_SET_VCPU_EVENTS to guard against
     accessing memslots if toggling SMM happens to force a VM-Exit

   - Emulate MSR_{FS,GS}_BASE on SVM even though interception is always
     disabled, so that KVM does the right thing if KVM's emulator
     encounters {RD,WR}MSR

   - Explicitly clear BUS_LOCK_DETECT from KVM's caps on AMD, as KVM
     doesn't yet virtualize BUS_LOCK_DETECT on AMD

   - Cleanup the help message for CONFIG_KVM_AMD_SEV, and call out that
     KVM now supports SEV-SNP too

   - Specialize return value of
     KVM_CHECK_EXTENSION(KVM_CAP_READONLY_MEM), based on VM type

   - Remove unnecessary dependency on CONFIG_HIGH_RES_TIMERS

   - Note an RCU quiescent state on guest exit. This avoids a call to
     rcu_core() if there was a grace period request while guest was
     running"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Remove HIGH_RES_TIMERS dependency
  kvm: Note an RCU quiescent state on guest exit
  KVM: x86: Only advertise KVM_CAP_READONLY_MEM when supported by VM
  KVM: SEV: Update KVM_AMD_SEV Kconfig entry and mention SEV-SNP
  KVM: SVM: Don't advertise Bus Lock Detect to guest if SVM support is missing
  KVM: SVM: fix emulation of msr reads/writes of MSR_FS_BASE and MSR_GS_BASE
  KVM: x86: Acquire kvm->srcu when handling KVM_SET_VCPU_EVENTS
  KVM: x86/mmu: Check that root is valid/loaded when pre-faulting SPTEs
  KVM: x86/mmu: Fixup comments missed by the REMOVED_SPTE=>FROZEN_SPTE rename

Pull power management fix from Rafael Wysocki:
 "Fix an incorrect warning emitted by the amd-pstate driver on
  processors that don't support X86_FEATURE_CPPC (Gautham Shenoy)"

* tag 'pm-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq/amd-pstate: Remove warning for X86_FEATURE_CPPC on certain Zen models

Pull block fixes from Jens Axboe:
 "Mostly just some fixlets for NVMe, but also a bug fix for the ublk
  driver and an integrity fix"

* tag 'block-6.11-20240906' of git://git.kernel.dk/linux:
  bio-integrity: don't restrict the size of integrity metadata
  ublk_drv: fix NULL pointer dereference in ublk_ctrl_start_recovery()
  nvmet: Identify-Active Namespace ID List command should reject invalid nsid
  nvme: set BLK_FEAT_ZONED for ZNS multipath disks
  nvme-pci: Add sleep quirk for Samsung 990 Evo
  nvme-pci: allocate tagset on reset if necessary
  nvmet-tcp: fix kernel crash if commands allocation fails
  nvme: use better description for async reset reason
  nvmet: Make nvmet_debugfs static

Pull sound fixes from Takashi Iwai:
 "Hopefully the last PR for 6.11, at least for this level of amount.

  In addition to the usual HD-audio quirks, there are more changes in
  ASoC, but all look small and device-specific fixes, and nothing stands
  out. The only slightly big change is sunxi I2S fix, which looks quite
  safe to apply, too"

* tag 'sound-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
  ALSA: hda/realtek - Fix inactive headset mic jack for ASUS Vivobook 15 X1504VAP
  ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
  ALSA: hda/realtek: Enable Mute Led for HP Victus 15-fb1xxx
  ALSA: hda/realtek: extend quirks for Clevo V5[46]0
  ASoC: codecs: lpass-va-macro: set the default codec version for sm8250
  ALSA: hda: add HDMI codec ID for Intel PTL
  ALSA: hda/realtek: add patch for internal mic in Lenovo V145
  ASoC: sunxi: sun4i-i2s: fix LRCLK polarity in i2s mode
  ASoC: amd: yc: Add a quirk for MSI Bravo 17 (D7VEK)
  ASoC: mediatek: mt8188-mt6359: Modify key
  ASoc: SOF: topology: Clear SOF link platform name upon unload
  ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius devices
  ASoC: SOF: ipc: replace "enum sof_comp_type" field with "uint32_t"
  ASoC: fix module autoloading
  ASoC: tda7419: fix module autoloading
  ASoC: google: fix module autoloading
  ASoC: intel: fix module autoloading
  ASoC: tegra: Fix CBB error during probe()
  ASoC: dapm: Fix UAF for snd_soc_pcm_runtime object
  ASoC: Intel: soc-acpi-cht: Make Lenovo Yoga Tab 3 X90F DMI match less strict
  ...

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Apply SD quirks earlier during probe so they become relevant

  MMC host:
   - cqhci: Fix checking of CQHCI_HALT state
   - dw_mmc: Fix IDMAC operation with pages bigger than 4K
   - sdhci-of-aspeed: Fix module autoloading"

* tag 'mmc-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: cqhci: Fix checking of CQHCI_HALT state
  mmc: dw_mmc: Fix IDMAC operation with pages bigger than 4K
  mmc: sdhci-of-aspeed: fix module autoloading
  mmc: core: apply SD quirks earlier during probe

Pull gpio fixes from Bartosz Golaszewski:

 - fix an OF node reference leak in gpio-rockchip

 - add the missing module device table to gpio-modepin

* tag 'gpio-fixes-for-v6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: modepin: Enable module autoloading
  gpio: rockchip: fix OF node leak in probe()

Pull pmdomain fix from Ulf Hansson:

 - Fix support for required OPPs for multiple PM domains

* tag 'pmdomain-v6.11-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
  OPP: Fix support for required OPPs for multiple PM domains

Pull pwm fix from Uwe Kleine-König:
 "Fix an off-by-one in the stm32 driver.

  Hardware engineers tend to start counting at 1 while the software guys
  usually start with 0. This isn't so nice because that results in
  drivers where pwm device #2 needs to use the hardware registers with
  index 3.

  This was noticed by Fabrice Gasnier.

  A small patch fixing that mismatch is the only change included here"

* tag 'pwm/for-6.11-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
  pwm: stm32: Use the right CCxNP bit in stm32_pwm_enable()

Pull drm fixes from Dave Airlie:
 "This has a fair few patches in it, but I reviewed them all and they
  seem like real things, amdgpu, i915 and xe each have a bunch of fixes
  for various things, then there is a some bridge suspend/resume
  ordering fixes for a recent rework, and then some single driver
  changes in a few others.

  Nothing looks too serious, hopefully next week is quiet.

  amdgpu:
   - IPS workaround
   - Fix compatibility with older MES firmware
   - Fix CPU spikes when clearing VRAM
   - Backlight fix
   - PMO fix
   - Revert SWSMU change to fix regression

  xe:
   - GSC loading fix
   - PCODE mutex fix
   - Suspend/Resume fixes
   - RPM fixes

  i915:
   - Do not attempt to load the GSC multiple times
   - Fix readout degamma_lut mismatch on ilk/snb
   - Mark debug_fence_init_onstack() with __maybe_unused
   - fence: Mark debug_fence_free() with __maybe_unused
   - display: Add mechanism to use sink model when applying quirk
   - display: Increase Fast Wake Sync length as a quirk

  komeda:
   - zpos normalization fix

  nouveau:
   - incorrect register fix

  imagination:
   - memory leak fix

  bridge:
   - hdmi/bridge rework fixes

  panthor:
   - cache coherency fix
   - hi priority access fix

  panel:
   - change of compatible string

  fbdev:
   - deferred-io init with no struct page fix"

* tag 'drm-fixes-2024-09-06' of https://gitlab.freedesktop.org/drm/kernel: (29 commits)
  Revert "drm/amdgpu: align pp_power_profile_mode with kernel docs"
  drm/fbdev-dma: Only install deferred I/O if necessary
  drm/panthor: flush FW AS caches in slow reset path
  drm: panel: nv3052c: Correct WL-355608-A8 panel compatible
  dt-bindings: display: panel: Rename WL-355608-A8 panel to rg35xx-*-panel
  drm/panthor: Restrict high priorities on group_create
  drm/xe/display: Avoid encoder_suspend at runtime suspend
  drm/xe: Suspend/resume user access only during system s/r
  drm/xe/display: Match i915 driver suspend/resume sequences better
  drm/xe: Add missing runtime reference to wedged upon gt_reset
  drm/xe/pcode: Treat pcode as per-tile rather than per-GT
  drm/xe/gsc: Do not attempt to load the GSC multiple times
  drm/bridge-connector: reset the HDMI connector state
  drm/bridge-connector: move to DRM_DISPLAY_HELPER module
  drm/display: stop depending on DRM_DISPLAY_HELPER
  drm/i915/display: Increase Fast Wake Sync length as a quirk
  drm/i915/display: Add mechanism to use sink model when applying quirk
  drm/amd/display: Block timing sync for different signals in PMO
  drm/amd/display: Lock DC and exit IPS when changing backlight
  drm/amdgpu: always allocate cleared VRAM for GEM allocations
  ...

get_stashed_dentry() tries to optimistically retrieve a stashed dentry
from a provided location.  It needs to ensure to hold rcu lock before it
dereference the stashed location to prevent UAF issues.  Use
rcu_dereference() instead of READ_ONCE() it's effectively equivalent
with some lockdep bells and whistles and it communicates clearly that
this expects rcu protection.

Link: https://lore.kernel.org/r/20240906-vfs-hotfix-5959800ffa68@brauner
Fixes: 07fd7c32 ("libfs: add path_from_stashed()")
Reported-by: syzbot+f82b36bffae7ef78b6a7@syzkaller.appspotmail.com
Fixes: syzbot+f82b36bffae7ef78b6a7@syzkaller.appspotmail.com
Reported-by: syzbot+cbe4b96e1194b0e34db6@syzkaller.appspotmail.com
Fixes: syzbot+cbe4b96e1194b0e34db6@syzkaller.appspotmail.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add the device id for the Macrosilicon MS3020 which is a
PL2303HXN based device.
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>