I noticed that only 3 out of the 4 input bits were used,
mt.key->flags & FLOW_DIS_IS_FRAGMENT was never checked.

In order to avoid a complicated maze, I converted it to
use a 16 byte mapping table.

As shown in the table below the old heuristics doesn't
always do the right thing, ie. when FLOW_DIS_IS_FRAGMENT=1/1
then it used to only match follow-up fragment packets.

Here are all the combinations, and their resulting new/old
VCAP key/mask filter:

  /- FLOW_DIS_IS_FRAGMENT (key/mask)
  |    /- FLOW_DIS_FIRST_FRAG (key/mask)
  |    |    /-- new VCAP fragment (key/mask)
  v    v    v    v- old VCAP fragment (key/mask)

 0/0  0/0  -/-  -/-     impossible (due to entry cond. on mask)
 0/0  0/1  -/-  0/3 !!  invalid (can't match non-fragment + follow-up frag)
 0/0  1/0  -/-  -/-     impossible (key > mask)
 0/0  1/1  1/3  1/3     first fragment

 0/1  0/0  0/3  3/3 !!  not fragmented
 0/1  0/1  0/3  3/3 !!  not fragmented (+ not first fragment)
 0/1  1/0  -/-  -/-     impossible (key > mask)
 0/1  1/1  -/-  1/3 !!  invalid (non-fragment and first frag)

 1/0  0/0  -/-  -/-     impossible (key > mask)
 1/0  0/1  -/-  -/-     impossible (key > mask)
 1/0  1/0  -/-  -/-     impossible (key > mask)
 1/0  1/1  -/-  -/-     impossible (key > mask)

 1/1  0/0  1/1  3/3 !!  some fragment
 1/1  0/1  3/3  3/3     follow-up fragment
 1/1  1/0  -/-  -/-     impossible (key > mask)
 1/1  1/1  1/3  1/3     first fragment

In the datasheet the VCAP fragment values are documented as:
 0 = no fragment
 1 = initial fragment
 2 = suspicious fragment
 3 = valid follow-up fragment

Result: 3 combinations match the old behavior,
        3 combinations have been corrected,
        2 combinations are now invalid, and fail,
        8 combinations are impossible.

It should now be aligned with how FLOW_DIS_IS_FRAGMENT
and FLOW_DIS_FIRST_FRAG is set in __skb_flow_dissect() in
net/core/flow_dissector.c

Since the VCAP fragment values are not a bitfield, we have
to ignore the suspicious fragment value, eg. when matching
on any kind of fragment with FLOW_DIS_IS_FRAGMENT=1/1.

Only compile tested, and logic tested in userspace, as I
unfortunately don't have access to this switch chip (yet).

Fixes: d6c2964d ("net: microchip: sparx5: Adding more tc flower keys for the IS2 VCAP")
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Tested-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240411111321.114095-1-ast@fiberby.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kuniyuki Iwashima says:

====================
af_unix: Fix MSG_OOB bugs with MSG_PEEK.

Currently, OOB data can be read without MSG_OOB accidentally
in two cases, and this seris fixes the bugs.

v1: https://lore.kernel.org/netdev/20240409225209.58102-1-kuniyu@amazon.com/
====================

Link: https://lore.kernel.org/r/20240410171016.7621-1-kuniyu@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, we can read OOB data without MSG_OOB by using MSG_PEEK
when OOB data is sitting on the front row, which is apparently
wrong.

  >>> from socket import *
  >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
  >>> c1.send(b'a', MSG_OOB)
  1
  >>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
  b'a'

If manage_oob() is called when no data has been copied, we only
check if the socket enables SO_OOBINLINE or MSG_PEEK is not used.
Otherwise, the skb is returned as is.

However, here we should return NULL if MSG_PEEK is set and no data
has been copied.

Also, in such a case, we should not jump to the redo label because
we will be caught in the loop and hog the CPU until normal data
comes in.

Then, we need to handle skb == NULL case with the if-clause below
the manage_oob() block.

With this patch:

  >>> from socket import *
  >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
  >>> c1.send(b'a', MSG_OOB)
  1
  >>> c2.recv(1, MSG_PEEK | MSG_DONTWAIT)
  Traceback (most recent call last):
    File "<stdin>", line 1, in <module>
  BlockingIOError: [Errno 11] Resource temporarily unavailable

Fixes: 314001f0 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240410171016.7621-3-kuniyu@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When we call recv() for AF_UNIX socket, we first peek one skb and
calls manage_oob() to check if the skb is sent with MSG_OOB.

However, when we fetch the next (and the following) skb, manage_oob()
is not called now, leading a wrong behaviour.

Let's say a socket send()s "hello" with MSG_OOB and the peer tries
to recv() 5 bytes with MSG_PEEK.  Here, we should get only "hell"
without 'o', but actually not:

  >>> from socket import *
  >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
  >>> c1.send(b'hello', MSG_OOB)
  5
  >>> c2.recv(5, MSG_PEEK)
  b'hello'

The first skb fills 4 bytes, and the next skb is peeked but not
properly checked by manage_oob().

Let's move up the again label to call manage_oob() for evry skb.

With this patch:

  >>> from socket import *
  >>> c1, c2 = socketpair(AF_UNIX, SOCK_STREAM)
  >>> c1.send(b'hello', MSG_OOB)
  5
  >>> c2.recv(5, MSG_PEEK)
  b'hell'

Fixes: 314001f0 ("af_unix: Add OOB support")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240410171016.7621-2-kuniyu@amazon.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

netfilter pull request 24-04-11

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

Patches #1 and #2 add missing rcu read side lock when iterating over
expression and object type list which could race with module removal.

Patch #3 prevents promisc packet from visiting the bridge/input hook
	 to amend a recent fix to address conntrack confirmation race
	 in br_netfilter and nf_conntrack_bridge.

Patch #4 adds and uses iterate decorator type to fetch the current
	 pipapo set backend datastructure view when netlink dumps the
	 set elements.

Patch #5 fixes removal of duplicate elements in the pipapo set backend.

Patch #6 flowtable validates pppoe header before accessing it.

Patch #7 fixes flowtable datapath for pppoe packets, otherwise lookup
         fails and pppoe packets follow classic path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bluetooth.

  Current release - new code bugs:

   - netfilter: complete validation of user input

   - mlx5: disallow SRIOV switchdev mode when in multi-PF netdev

  Previous releases - regressions:

   - core: fix u64_stats_init() for lockdep when used repeatedly in one
     file

   - ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr

   - bluetooth: fix memory leak in hci_req_sync_complete()

   - batman-adv: avoid infinite loop trying to resize local TT

   - drv: geneve: fix header validation in geneve[6]_xmit_skb

   - drv: bnxt_en: fix possible memory leak in
     bnxt_rdma_aux_device_init()

   - drv: mlx5: offset comp irq index in name by one

   - drv: ena: avoid double-free clearing stale tx_info->xdpf value

   - drv: pds_core: fix pdsc_check_pci_health deadlock

  Previous releases - always broken:

   - xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING

   - bluetooth: fix setsockopt not validating user input

   - af_unix: clear stale u->oob_skb.

   - nfc: llcp: fix nfc_llcp_setsockopt() unsafe copies

   - drv: virtio_net: fix guest hangup on invalid RSS update

   - drv: mlx5e: Fix mlx5e_priv_init() cleanup flow

   - dsa: mt7530: trap link-local frames regardless of ST Port State"

* tag 'net-6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (59 commits)
  net: ena: Set tx_info->xdpf value to NULL
  net: ena: Fix incorrect descriptor free behavior
  net: ena: Wrong missing IO completions check order
  net: ena: Fix potential sign extension issue
  af_unix: Fix garbage collector racing against connect()
  net: dsa: mt7530: trap link-local frames regardless of ST Port State
  Revert "s390/ism: fix receive message buffer allocation"
  net: sparx5: fix wrong config being used when reconfiguring PCS
  net/mlx5: fix possible stack overflows
  net/mlx5: Disallow SRIOV switchdev mode when in multi-PF netdev
  net/mlx5e: RSS, Block XOR hash with over 128 channels
  net/mlx5e: Do not produce metadata freelist entries in Tx port ts WQE xmit
  net/mlx5e: HTB, Fix inconsistencies with QoS SQs number
  net/mlx5e: Fix mlx5e_priv_init() cleanup flow
  net/mlx5e: RSS, Block changing channels number when RXFH is configured
  net/mlx5: Correctly compare pkt reformat ids
  net/mlx5: Properly link new fs rules into the tree
  net/mlx5: offset comp irq index in name by one
  net/mlx5: Register devlink first under devlink lock
  net/mlx5: E-switch, store eswitch pointer before registering devlink_param
  ...

Pull SCSI fixes from James Bottomley:
 "The most important fix is the sg one because the regression it fixes
  (spurious warning and use after final put) is already backported to
  stable.

  The next biggest impact is the target fix for wrong credentials used
  to load a module because it's affecting new kernels installed on
  selinux based distributions.

  The other three fixes are an obvious off by one and SATA protocol
  issues"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix off by one in qla_edif_app_getstats()
  scsi: hisi_sas: Modify the deadline for ata_wait_after_reset()
  scsi: hisi_sas: Handle the NCQ error returned by D2H frame
  scsi: target: Fix SELinux error when systemd-modules loads the target module
  scsi: sg: Avoid race in error handling & drop bogus warn

Merge tag 'loongarch-fixes-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch fixes from Huacai Chen:

 - make {virt, phys, page, pfn} translation work with KFENCE for
   LoongArch (otherwise NVMe and virtio-blk cannot work with KFENCE
   enabled)

 - update dts files for Loongson-2K series to make devices work
   correctly

 - fix a build error

* tag 'loongarch-fixes-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  LoongArch: Include linux/sizes.h in addrspace.h to prevent build errors
  LoongArch: Update dts for Loongson-2K2000 to support GMAC/GNET
  LoongArch: Update dts for Loongson-2K2000 to support PCI-MSI
  LoongArch: Update dts for Loongson-2K2000 to support ISA/LPC
  LoongArch: Update dts for Loongson-2K1000 to support ISA/LPC
  LoongArch: Make virt_addr_valid()/__virt_addr_valid() work with KFENCE
  LoongArch: Make {virt, phys, page, pfn} translation work with KFENCE
  mm: Move lowmem_page_address() a little later

Pull more bcachefs fixes from Kent Overstreet:
 "Notable user impacting bugs

   - On multi device filesystems, recovery was looping in
     btree_trans_too_many_iters(). This checks if a transaction has
     touched too many btree paths (because of iteration over many keys),
     and isuses a restart to drop unneeded paths.

     But it's now possible for some paths to exceed the previous limit
     without iteration in the interior btree update path, since the
     transaction commit will do alloc updates for every old and new
     btree node, and during journal replay we don't use the btree write
     buffer for locking reasons and thus those updates use btree paths
     when they wouldn't normally.

   - Fix a corner case in rebalance when moving extents on a
     durability=0 device. This wouldn't be hit when a device was
     formatted with durability=0 since in that case we'll only use it as
     a write through cache (only cached extents will live on it), but
     durability can now be changed on an existing device.

   - bch2_get_acl() could rarely forget to handle a transaction restart;
     this manifested as the occasional missing acl that came back after
     dropping caches.

   - Fix a major performance regression on high iops multithreaded write
     workloads (only since 6.9-rc1); a previous fix for a deadlock in
     the interior btree update path to check the journal watermark
     introduced a dependency on the state of btree write buffer flushing
     that we didn't want.

   - Assorted other repair paths and recovery fixes"

* tag 'bcachefs-2024-04-10' of https://evilpiepirate.org/git/bcachefs: (25 commits)
  bcachefs: Fix __bch2_btree_and_journal_iter_init_node_iter()
  bcachefs: Kill read lock dropping in bch2_btree_node_lock_write_nofail()
  bcachefs: Fix a race in btree_update_nodes_written()
  bcachefs: btree_node_scan: Respect member.data_allowed
  bcachefs: Don't scan for btree nodes when we can reconstruct
  bcachefs: Fix check_topology() when using node scan
  bcachefs: fix eytzinger0_find_gt()
  bcachefs: fix bch2_get_acl() transaction restart handling
  bcachefs: fix the count of nr_freed_pcpu after changing bc->freed_nonpcpu list
  bcachefs: Fix gap buffer bug in bch2_journal_key_insert_take()
  bcachefs: Rename struct field swap to prevent macro naming collision
  MAINTAINERS: Add entry for bcachefs documentation
  Documentation: filesystems: Add bcachefs toctree
  bcachefs: JOURNAL_SPACE_LOW
  bcachefs: Disable errors=panic for BCH_IOCTL_FSCK_OFFLINE
  bcachefs: Fix BCH_IOCTL_FSCK_OFFLINE for encrypted filesystems
  bcachefs: fix rand_delete unit test
  bcachefs: fix ! vs ~ typo in __clear_bit_le64()
  bcachefs: Fix rebalance from durability=0 device
  bcachefs: Print shutdown journal sequence number
  ...

Merge tag 'tag-chrome-platform-fixes-for-v6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform fix from Tzung-Bi Shih:
 "Fix a NULL pointer dereference"

* tag 'tag-chrome-platform-fixes-for-v6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_ec_uart: properly fix race condition

pppoe traffic reaching ingress path does not match the flowtable entry
because the pppoe header is expected to be at the network header offset.
This bug causes a mismatch in the flow table lookup, so pppoe packets
enter the classical forwarding path.

Fixes: 72efd585 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Ensure there is sufficient room to access the protocol field of the
PPPoe header. Validate it once before the flowtable lookup, then use a
helper function to access protocol field.

Reported-by: syzbot+b6f07e1c07ef40199081@syzkaller.appspotmail.com
Fixes: 72efd585 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pablo reports a crash with large batches of elements with a
back-to-back add/remove pattern.  Quoting Pablo:

  add_elem("00000000") timeout 100 ms
  ...
  add_elem("0000000X") timeout 100 ms
  del_elem("0000000X") <---------------- delete one that was just added
  ...
  add_elem("00005000") timeout 100 ms

  1) nft_pipapo_remove() removes element 0000000X
  Then, KASAN shows a splat.

Looking at the remove function there is a chance that we will drop a
rule that maps to a non-deactivated element.

Removal happens in two steps, first we do a lookup for key k and return the
to-be-removed element and mark it as inactive in the next generation.
Then, in a second step, the element gets removed from the set/map.

The _remove function does not work correctly if we have more than one
element that share the same key.

This can happen if we insert an element into a set when the set already
holds an element with same key, but the element mapping to the existing
key has timed out or is not active in the next generation.

In such case its possible that removal will unmap the wrong element.
If this happens, we will leak the non-deactivated element, it becomes
unreachable.

The element that got deactivated (and will be freed later) will
remain reachable in the set data structure, this can result in
a crash when such an element is retrieved during lookup (stale
pointer).

Add a check that the fully matching key does in fact map to the element
that we have marked as inactive in the deactivation step.
If not, we need to continue searching.

Add a bug/warn trap at the end of the function as well, the remove
function must not ever be called with an invisible/unreachable/non-existent
element.

v2: avoid uneeded temporary variable (Stefano)

Fixes: 3c4287f6 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The generation mask can be updated while netlink dump is in progress.
The pipapo set backend walk iterator cannot rely on it to infer what
view of the datastructure is to be used. Add notation to specify if user
wants to read/update the set.

Based on patch from Florian Westphal.

Fixes: 2b84e215 ("netfilter: nft_set_pipapo: .walk does not deal with generations")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

For historical reasons, when bridge device is in promisc mode, packets
that are directed to the taps follow bridge input hook path. This patch
adds a workaround to reset conntrack for these packets.

Jianbo Liu reports warning splats in their test infrastructure where
cloned packets reach the br_netfilter input hook to confirm the
conntrack object.

Scratch one bit from BR_INPUT_SKB_CB to annotate that this packet has
reached the input hook because it is passed up to the bridge device to
reach the taps.

[   57.571874] WARNING: CPU: 1 PID: 0 at net/bridge/br_netfilter_hooks.c:616 br_nf_local_in+0x157/0x180 [br_netfilter]
[   57.572749] Modules linked in: xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_isc si ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5ctl mlx5_core
[   57.575158] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.8.0+ #19
[   57.575700] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[   57.576662] RIP: 0010:br_nf_local_in+0x157/0x180 [br_netfilter]
[   57.577195] Code: fe ff ff 41 bd 04 00 00 00 be 04 00 00 00 e9 4a ff ff ff be 04 00 00 00 48 89 ef e8 f3 a9 3c e1 66 83 ad b4 00 00 00 04 eb 91 <0f> 0b e9 f1 fe ff ff 0f 0b e9 df fe ff ff 48 89 df e8 b3 53 47 e1
[   57.578722] RSP: 0018:ffff88885f845a08 EFLAGS: 00010202
[   57.579207] RAX: 0000000000000002 RBX: ffff88812dfe8000 RCX: 0000000000000000
[   57.579830] RDX: ffff88885f845a60 RSI: ffff8881022dc300 RDI: 0000000000000000
[   57.580454] RBP: ffff88885f845a60 R08: 0000000000000001 R09: 0000000000000003
[   57.581076] R10: 00000000ffff1300 R11: 0000000000000002 R12: 0000000000000000
[   57.581695] R13: ffff8881047ffe00 R14: ffff888108dbee00 R15: ffff88814519b800
[   57.582313] FS:  0000000000000000(0000) GS:ffff88885f840000(0000) knlGS:0000000000000000
[   57.583040] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   57.583564] CR2: 000000c4206aa000 CR3: 0000000103847001 CR4: 0000000000370eb0
[   57.584194] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[   57.584820] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[   57.585440] Call Trace:
[   57.585721]  <IRQ>
[   57.585976]  ? __warn+0x7d/0x130
[   57.586323]  ? br_nf_local_in+0x157/0x180 [br_netfilter]
[   57.586811]  ? report_bug+0xf1/0x1c0
[   57.587177]  ? handle_bug+0x3f/0x70
[   57.587539]  ? exc_invalid_op+0x13/0x60
[   57.587929]  ? asm_exc_invalid_op+0x16/0x20
[   57.588336]  ? br_nf_local_in+0x157/0x180 [br_netfilter]
[   57.588825]  nf_hook_slow+0x3d/0xd0
[   57.589188]  ? br_handle_vlan+0x4b/0x110
[   57.589579]  br_pass_frame_up+0xfc/0x150
[   57.589970]  ? br_port_flags_change+0x40/0x40
[   57.590396]  br_handle_frame_finish+0x346/0x5e0
[   57.590837]  ? ipt_do_table+0x32e/0x430
[   57.591221]  ? br_handle_local_finish+0x20/0x20
[   57.591656]  br_nf_hook_thresh+0x4b/0xf0 [br_netfilter]
[   57.592286]  ? br_handle_local_finish+0x20/0x20
[   57.592802]  br_nf_pre_routing_finish+0x178/0x480 [br_netfilter]
[   57.593348]  ? br_handle_local_finish+0x20/0x20
[   57.593782]  ? nf_nat_ipv4_pre_routing+0x25/0x60 [nf_nat]
[   57.594279]  br_nf_pre_routing+0x24c/0x550 [br_netfilter]
[   57.594780]  ? br_nf_hook_thresh+0xf0/0xf0 [br_netfilter]
[   57.595280]  br_handle_frame+0x1f3/0x3d0
[   57.595676]  ? br_handle_local_finish+0x20/0x20
[   57.596118]  ? br_handle_frame_finish+0x5e0/0x5e0
[   57.596566]  __netif_receive_skb_core+0x25b/0xfc0
[   57.597017]  ? __napi_build_skb+0x37/0x40
[   57.597418]  __netif_receive_skb_list_core+0xfb/0x220

Fixes: 62e7151a ("netfilter: bridge: confirm multicast packets before passing them up the stack")
Reported-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nft_unregister_obj() can concurrent with __nft_obj_type_get(),
and there is not any protection when iterate over nf_tables_objects
list in __nft_obj_type_get(). Therefore, there is potential data-race
of nf_tables_objects list entry.

Use list_for_each_entry_rcu() to iterate over nf_tables_objects
list in __nft_obj_type_get(), and use rcu_read_lock() in the caller
nft_obj_type_get() to protect the entire type query process.

Fixes: e5009240 ("netfilter: nf_tables: add stateful objects")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nft_unregister_expr() can concurrent with __nft_expr_type_get(),
and there is not any protection when iterate over nf_tables_expressions
list in __nft_expr_type_get(). Therefore, there is potential data-race
of nf_tables_expressions list entry.

Use list_for_each_entry_rcu() to iterate over nf_tables_expressions
list in __nft_expr_type_get(), and use rcu_read_lock() in the caller
nft_expr_type_get() to protect the entire type query process.

Fixes: ef1f7df9 ("netfilter: nf_tables: expression ops overloading")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

David Arinzon says:

====================
ENA driver bug fixes

From: David Arinzon <darinzon@amazon.com>

This patchset contains multiple bug fixes for the
ENA driver.
====================

Link: https://lore.kernel.org/r/20240410091358.16289-1-darinzon@amazon.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The patch mentioned in the `Fixes` tag removed the explicit assignment
of tx_info->xdpf to NULL with the justification that there's no need
to set tx_info->xdpf to NULL and tx_info->num_of_bufs to 0 in case
of a mapping error. Both values won't be used once the mapping function
returns an error, and their values would be overridden by the next
transmitted packet.

While both values do indeed get overridden in the next transmission
call, the value of tx_info->xdpf is also used to check whether a TX
descriptor's transmission has been completed (i.e. a completion for it
was polled).

An example scenario:
1. Mapping failed, tx_info->xdpf wasn't set to NULL
2. A VF reset occurred leading to IO resource destruction and
   a call to ena_free_tx_bufs() function
3. Although the descriptor whose mapping failed was freed by the
   transmission function, it still passes the check
     if (!tx_info->skb)

   (skb and xdp_frame are in a union)
4. The xdp_frame associated with the descriptor is freed twice

This patch returns the assignment of NULL to tx_info->xdpf to make the
cleaning function knows that the descriptor is already freed.

Fixes: 504fd6a5 ("net: ena: fix DMA mapping function issues in XDP")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ENA has two types of TX queues:
- queues which only process TX packets arriving from the network stack
- queues which only process TX packets forwarded to it by XDP_REDIRECT
  or XDP_TX instructions

The ena_free_tx_bufs() cycles through all descriptors in a TX queue
and unmaps + frees every descriptor that hasn't been acknowledged yet
by the device (uncompleted TX transactions).
The function assumes that the processed TX queue is necessarily from
the first category listed above and ends up using napi_consume_skb()
for descriptors belonging to an XDP specific queue.

This patch solves a bug in which, in case of a VF reset, the
descriptors aren't freed correctly, leading to crashes.

Fixes: 548c4940 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Missing IO completions check is called every second (HZ jiffies).
This commit fixes several issues with this check:

1. Duplicate queues check:
   Max of 4 queues are scanned on each check due to monitor budget.
   Once reaching the budget, this check exits under the assumption that
   the next check will continue to scan the remainder of the queues,
   but in practice, next check will first scan the last already scanned
   queue which is not necessary and may cause the full queue scan to
   last a couple of seconds longer.
   The fix is to start every check with the next queue to scan.
   For example, on 8 IO queues:
   Bug: [0,1,2,3], [3,4,5,6], [6,7]
   Fix: [0,1,2,3], [4,5,6,7]

2. Unbalanced queues check:
   In case the number of active IO queues is not a multiple of budget,
   there will be checks which don't utilize the full budget
   because the full scan exits when reaching the last queue id.
   The fix is to run every TX completion check with exact queue budget
   regardless of the queue id.
   For example, on 7 IO queues:
   Bug: [0,1,2,3], [4,5,6], [0,1,2,3]
   Fix: [0,1,2,3], [4,5,6,0], [1,2,3,4]
   The budget may be lowered in case the number of IO queues is less
   than the budget (4) to make sure there are no duplicate queues on
   the same check.
   For example, on 3 IO queues:
   Bug: [0,1,2,0], [1,2,0,1]
   Fix: [0,1,2], [0,1,2]

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Amit Bernstein <amitbern@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Small unsigned types are promoted to larger signed types in
the case of multiplication, the result of which may overflow.
In case the result of such a multiplication has its MSB
turned on, it will be sign extended with '1's.
This changes the multiplication result.

Code example of the phenomenon:
-------------------------------
u16 x, y;
size_t z1, z2;

x = y = 0xffff;
printk("x=%x y=%x\n",x,y);

z1 = x*y;
z2 = (size_t)x*y;

printk("z1=%lx z2=%lx\n", z1, z2);

Output:
-------
x=ffff y=ffff
z1=fffffffffffe0001 z2=fffe0001

The expected result of ffff*ffff is fffe0001, and without the
explicit casting to avoid the unwanted sign extension we got
fffffffffffe0001.

This commit adds an explicit casting to avoid the sign extension
issue.

Fixes: 689b2bda ("net: ena: add functions for handling Low Latency Queues in ena_com")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

  - L2CAP: Don't double set the HCI_CONN_MGMT_CONNECTED bit
  - Fix memory leak in hci_req_sync_complete
  - hci_sync: Fix using the same interval and window for Coded PHY
  - Fix not validating setsockopt user input

* tag 'for-net-2024-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: l2cap: Don't double set the HCI_CONN_MGMT_CONNECTED bit
  Bluetooth: hci_sock: Fix not validating setsockopt user input
  Bluetooth: ISO: Fix not validating setsockopt user input
  Bluetooth: L2CAP: Fix not validating setsockopt user input
  Bluetooth: RFCOMM: Fix not validating setsockopt user input
  Bluetooth: SCO: Fix not validating setsockopt user input
  Bluetooth: Fix memory leak in hci_req_sync_complete()
  Bluetooth: hci_sync: Fix using the same interval and window for Coded PHY
  Bluetooth: ISO: Don't reject BT_ISO_QOS if parameters are unset
====================

Link: https://lore.kernel.org/r/20240410191610.4156653-1-luiz.dentz@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Garbage collector does not take into account the risk of embryo getting
enqueued during the garbage collection. If such embryo has a peer that
carries SCM_RIGHTS, two consecutive passes of scan_children() may see a
different set of children. Leading to an incorrectly elevated inflight
count, and then a dangling pointer within the gc_inflight_list.

sockets are AF_UNIX/SOCK_STREAM
S is an unconnected socket
L is a listening in-flight socket bound to addr, not in fdtable
V's fd will be passed via sendmsg(), gets inflight count bumped

connect(S, addr)	sendmsg(S, [V]); close(V)	__unix_gc()
----------------	-------------------------	-----------

NS = unix_create1()
skb1 = sock_wmalloc(NS)
L = unix_find_other(addr)
unix_state_lock(L)
unix_peer(S) = NS
			// V count=1 inflight=0

 			NS = unix_peer(S)
 			skb2 = sock_alloc()
			skb_queue_tail(NS, skb2[V])

			// V became in-flight
			// V count=2 inflight=1

			close(V)

			// V count=1 inflight=1
			// GC candidate condition met

						for u in gc_inflight_list:
						  if (total_refs == inflight_refs)
						    add u to gc_candidates

						// gc_candidates={L, V}

						for u in gc_candidates:
						  scan_children(u, dec_inflight)

						// embryo (skb1) was not
						// reachable from L yet, so V's
						// inflight remains unchanged
__skb_queue_tail(L, skb1)
unix_state_unlock(L)
						for u in gc_candidates:
						  if (u.inflight)
						    scan_children(u, inc_inflight_move_tail)

						// V count=1 inflight=2 (!)

If there is a GC-candidate listening socket, lock/unlock its state. This
makes GC wait until the end of any ongoing connect() to that socket. After
flipping the lock, a possibly SCM-laden embryo is already enqueued. And if
there is another embryo coming, it can not possibly carry SCM_RIGHTS. At
this point, unix_inflight() can not happen because unix_gc_lock is already
taken. Inflight graph remains unaffected.

Fixes: 1fd05ba5 ("[AF_UNIX]: Rewrite garbage collector, fixes race.")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240409201047.1032217-1-mhal@rbox.coSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In Clause 5 of IEEE Std 802-2014, two sublayers of the data link layer
(DLL) of the Open Systems Interconnection basic reference model (OSI/RM)
are described; the medium access control (MAC) and logical link control
(LLC) sublayers. The MAC sublayer is the one facing the physical layer.

In 8.2 of IEEE Std 802.1Q-2022, the Bridge architecture is described. A
Bridge component comprises a MAC Relay Entity for interconnecting the Ports
of the Bridge, at least two Ports, and higher layer entities with at least
a Spanning Tree Protocol Entity included.

Each Bridge Port also functions as an end station and shall provide the MAC
Service to an LLC Entity. Each instance of the MAC Service is provided to a
distinct LLC Entity that supports protocol identification, multiplexing,
and demultiplexing, for protocol data unit (PDU) transmission and reception
by one or more higher layer entities.

It is described in 8.13.9 of IEEE Std 802.1Q-2022 that in a Bridge, the LLC
Entity associated with each Bridge Port is modeled as being directly
connected to the attached Local Area Network (LAN).

On the switch with CPU port architecture, CPU port functions as Management
Port, and the Management Port functionality is provided by software which
functions as an end station. Software is connected to an IEEE 802 LAN that
is wholly contained within the system that incorporates the Bridge.
Software provides access to the LLC Entity associated with each Bridge Port
by the value of the source port field on the special tag on the frame
received by software.

We call frames that carry control information to determine the active
topology and current extent of each Virtual Local Area Network (VLAN),
i.e., spanning tree or Shortest Path Bridging (SPB) and Multiple VLAN
Registration Protocol Data Units (MVRPDUs), and frames from other link
constrained protocols, such as Extensible Authentication Protocol over LAN
(EAPOL) and Link Layer Discovery Protocol (LLDP), link-local frames. They
are not forwarded by a Bridge. Permanently configured entries in the
filtering database (FDB) ensure that such frames are discarded by the
Forwarding Process. In 8.6.3 of IEEE Std 802.1Q-2022, this is described in
detail:

Each of the reserved MAC addresses specified in Table 8-1
(01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]) shall be
permanently configured in the FDB in C-VLAN components and ERs.

Each of the reserved MAC addresses specified in Table 8-2
(01-80-C2-00-00-[01,02,03,04,05,06,07,08,09,0A,0E]) shall be permanently
configured in the FDB in S-VLAN components.

Each of the reserved MAC addresses specified in Table 8-3
(01-80-C2-00-00-[01,02,04,0E]) shall be permanently configured in the FDB
in TPMR components.

The FDB entries for reserved MAC addresses shall specify filtering for all
Bridge Ports and all VIDs. Management shall not provide the capability to
modify or remove entries for reserved MAC addresses.

The addresses in Table 8-1, Table 8-2, and Table 8-3 determine the scope of
propagation of PDUs within a Bridged Network, as follows:

  The Nearest Bridge group address (01-80-C2-00-00-0E) is an address that
  no conformant Two-Port MAC Relay (TPMR) component, Service VLAN (S-VLAN)
  component, Customer VLAN (C-VLAN) component, or MAC Bridge can forward.
  PDUs transmitted using this destination address, or any other addresses
  that appear in Table 8-1, Table 8-2, and Table 8-3
  (01-80-C2-00-00-[00,01,02,03,04,05,06,07,08,09,0A,0B,0C,0D,0E,0F]), can
  therefore travel no further than those stations that can be reached via a
  single individual LAN from the originating station.

  The Nearest non-TPMR Bridge group address (01-80-C2-00-00-03), is an
  address that no conformant S-VLAN component, C-VLAN component, or MAC
  Bridge can forward; however, this address is relayed by a TPMR component.
  PDUs using this destination address, or any of the other addresses that
  appear in both Table 8-1 and Table 8-2 but not in Table 8-3
  (01-80-C2-00-00-[00,03,05,06,07,08,09,0A,0B,0C,0D,0F]), will be relayed
  by any TPMRs but will propagate no further than the nearest S-VLAN
  component, C-VLAN component, or MAC Bridge.

  The Nearest Customer Bridge group address (01-80-C2-00-00-00) is an
  address that no conformant C-VLAN component, MAC Bridge can forward;
  however, it is relayed by TPMR components and S-VLAN components. PDUs
  using this destination address, or any of the other addresses that appear
  in Table 8-1 but not in either Table 8-2 or Table 8-3
  (01-80-C2-00-00-[00,0B,0C,0D,0F]), will be relayed by TPMR components and
  S-VLAN components but will propagate no further than the nearest C-VLAN
  component or MAC Bridge.

Because the LLC Entity associated with each Bridge Port is provided via CPU
port, we must not filter these frames but forward them to CPU port.

In a Bridge, the transmission Port is majorly decided by ingress and egress
rules, FDB, and spanning tree Port State functions of the Forwarding
Process. For link-local frames, only CPU port should be designated as
destination port in the FDB, and the other functions of the Forwarding
Process must not interfere with the decision of the transmission Port. We
call this process trapping frames to CPU port.

Therefore, on the switch with CPU port architecture, link-local frames must
be trapped to CPU port, and certain link-local frames received by a Port of
a Bridge comprising a TPMR component or an S-VLAN component must be
excluded from it.

A Bridge of the switch with CPU port architecture cannot comprise a
Two-Port MAC Relay (TPMR) component as a TPMR component supports only a
subset of the functionality of a MAC Bridge. A Bridge comprising two Ports
(Management Port doesn't count) of this architecture will either function
as a standard MAC Bridge or a standard VLAN Bridge.

Therefore, a Bridge of this architecture can only comprise S-VLAN
components, C-VLAN components, or MAC Bridge components. Since there's no
TPMR component, we don't need to relay PDUs using the destination addresses
specified on the Nearest non-TPMR section, and the proportion of the
Nearest Customer Bridge section where they must be relayed by TPMR
components.

One option to trap link-local frames to CPU port is to add static FDB
entries with CPU port designated as destination port. However, because that
Independent VLAN Learning (IVL) is being used on every VID, each entry only
applies to a single VLAN Identifier (VID). For a Bridge comprising a MAC
Bridge component or a C-VLAN component, there would have to be 16 times
4096 entries. This switch intellectual property can only hold a maximum of
2048 entries. Using this option, there also isn't a mechanism to prevent
link-local frames from being discarded when the spanning tree Port State of
the reception Port is discarding.

The remaining option is to utilise the BPC, RGAC1, RGAC2, RGAC3, and RGAC4
registers. Whilst this applies to every VID, it doesn't contain all of the
reserved MAC addresses without affecting the remaining Standard Group MAC
Addresses. The REV_UN frame tag utilised using the RGAC4 register covers
the remaining 01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F] destination
addresses. It also includes the 01-80-C2-00-00-22 to 01-80-C2-00-00-FF
destination addresses which may be relayed by MAC Bridges or VLAN Bridges.
The latter option provides better but not complete conformance.

This switch intellectual property also does not provide a mechanism to trap
link-local frames with specific destination addresses to CPU port by
Bridge, to conform to the filtering rules for the distinct Bridge
components.

Therefore, regardless of the type of the Bridge component, link-local
frames with these destination addresses will be trapped to CPU port:

01-80-C2-00-00-[00,01,02,03,0E]

In a Bridge comprising a MAC Bridge component or a C-VLAN component:

  Link-local frames with these destination addresses won't be trapped to
  CPU port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-[04,05,06,07,08,09,0A,0B,0C,0D,0F]

In a Bridge comprising an S-VLAN component:

  Link-local frames with these destination addresses will be trapped to CPU
  port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-00

  Link-local frames with these destination addresses won't be trapped to
  CPU port which won't conform to IEEE Std 802.1Q-2022:

  01-80-C2-00-00-[04,05,06,07,08,09,0A]

Currently on this switch intellectual property, if the spanning tree Port
State of the reception Port is discarding, link-local frames will be
discarded.

To trap link-local frames regardless of the spanning tree Port State, make
the switch regard them as Bridge Protocol Data Units (BPDUs). This switch
intellectual property only lets the frames regarded as BPDUs bypass the
spanning tree Port State function of the Forwarding Process.

With this change, the only remaining interference is the ingress rules.
When the reception Port has no PVID assigned on software, VLAN-untagged
frames won't be allowed in. There doesn't seem to be a mechanism on the
switch intellectual property to have link-local frames bypass this function
of the Forwarding Process.

Fixes: b8f126a8 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20240409-b4-for-net-mt7530-fix-link-local-when-stp-discarding-v2-1-07b1150164ac@arinc9.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 58effa34.
Review was not finished on this patch. So it's not ready for
upstreaming.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Link: https://lore.kernel.org/r/20240409113753.2181368-1-gbayer@linux.ibm.com
Fixes: 58effa34 ("s390/ism: fix receive message buffer allocation")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The wrong port config is being used if the PCS is reconfigured. Fix this
by correctly using the new config instead of the old one.

Fixes: 946e7fd5 ("net: sparx5: add port module support")
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240409-link-mode-reconfiguration-fix-v2-1-db6a507f3627@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

A couple of debug functions use a 512 byte temporary buffer and call another
function that has another buffer of the same size, which in turn exceeds the
usual warning limit for excessive stack usage:

drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:1073:1: error: stack frame size (1448) exceeds limit (1024) in 'dr_dump_start' [-Werror,-Wframe-larger-than]
dr_dump_start(struct seq_file *file, loff_t *pos)
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:1009:1: error: stack frame size (1120) exceeds limit (1024) in 'dr_dump_domain' [-Werror,-Wframe-larger-than]
dr_dump_domain(struct seq_file *file, struct mlx5dr_domain *dmn)
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_dbg.c:705:1: error: stack frame size (1104) exceeds limit (1024) in 'dr_dump_matcher_rx_tx' [-Werror,-Wframe-larger-than]
dr_dump_matcher_rx_tx(struct seq_file *file, bool is_rx,

Rework these so that each of the various code paths only ever has one of
these buffers in it, and exactly the functions that declare one have
the 'noinline_for_stack' annotation that prevents them from all being
inlined into the same caller.

Fixes: 917d1e79 ("net/mlx5: DR, Change SWS usage to debug fs seq_file interface")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/all/20240219100506.648089-1-arnd@kernel.org/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240408074142.3007036-1-arnd@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tariq Toukan says:

====================
mlx5 misc fixes

This patchset provides bug fixes to mlx5 driver.

This is V2 of the series previously submitted as PR by Saeed:
https://lore.kernel.org/netdev/20240326144646.2078893-1-saeed@kernel.org/T/

Series generated against:
commit 237f3cf1 ("xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING")
====================

Link: https://lore.kernel.org/r/20240409190820.227554-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Adaptations need to be made for the auxiliary device management in the
core driver level. Block this combination for now.

Fixes: 678eb448 ("net/mlx5: SD, Implement basic query and instantiation")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-12-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When supporting more than 128 channels, the RQT size is
calculated by multiplying the number of channels by 2
and rounding up to the nearest power of 2.

The index of the RQT is derived from the RSS hash
calculations. If XOR8 is used as the RSS hash function,
there are only 256 possible hash results, and therefore,
only 256 indexes can be reached in the RQT.

Block setting the RSS hash function to XOR when the number
of channels exceeds 128.

Fixes: 74a8dada ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-11-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Free Tx port timestamping metadata entries in the NAPI poll context and
consume metadata enties in the WQE xmit path. Do not free a Tx port
timestamping metadata entry in the WQE xmit path even in the error path to
avoid a race between two metadata entry producers.

Fixes: 3178308a ("net/mlx5e: Make tx_port_ts logic resilient to out-of-order CQEs")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-10-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When creating a new HTB class while the interface is down,
the variable that follows the number of QoS SQs (htb_max_qos_sqs)
may not be consistent with the number of HTB classes.

Previously, we compared these two values to ensure that
the node_qid is lower than the number of QoS SQs, and we
allocated stats for that SQ when they are equal.

Change the check to compare the node_qid with the current
number of leaf nodes and fix the checking conditions to
ensure allocation of stats_list and stats for each node.

Fixes: 214baf22 ("net/mlx5e: Support HTB offload")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-9-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When mlx5e_priv_init() fails, the cleanup flow calls mlx5e_selq_cleanup which
calls mlx5e_selq_apply() that assures that the `priv->state_lock` is held using
lockdep_is_held().

Acquire the state_lock in mlx5e_selq_cleanup().

Kernel log:
=============================
WARNING: suspicious RCU usage
6.8.0-rc3_net_next_841a9b5 #1 Not tainted
-----------------------------
drivers/net/ethernet/mellanox/mlx5/core/en/selq.c:124 suspicious rcu_dereference_protected() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by systemd-modules/293:
 #0: ffffffffa05067b0 (devices_rwsem){++++}-{3:3}, at: ib_register_client+0x109/0x1b0 [ib_core]
 #1: ffff8881096c65c0 (&device->client_data_rwsem){++++}-{3:3}, at: add_client_context+0x104/0x1c0 [ib_core]

stack backtrace:
CPU: 4 PID: 293 Comm: systemd-modules Not tainted 6.8.0-rc3_net_next_841a9b5 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0x8a/0xa0
 lockdep_rcu_suspicious+0x154/0x1a0
 mlx5e_selq_apply+0x94/0xa0 [mlx5_core]
 mlx5e_selq_cleanup+0x3a/0x60 [mlx5_core]
 mlx5e_priv_init+0x2be/0x2f0 [mlx5_core]
 mlx5_rdma_setup_rn+0x7c/0x1a0 [mlx5_core]
 rdma_init_netdev+0x4e/0x80 [ib_core]
 ? mlx5_rdma_netdev_free+0x70/0x70 [mlx5_core]
 ipoib_intf_init+0x64/0x550 [ib_ipoib]
 ipoib_intf_alloc+0x4e/0xc0 [ib_ipoib]
 ipoib_add_one+0xb0/0x360 [ib_ipoib]
 add_client_context+0x112/0x1c0 [ib_core]
 ib_register_client+0x166/0x1b0 [ib_core]
 ? 0xffffffffa0573000
 ipoib_init_module+0xeb/0x1a0 [ib_ipoib]
 do_one_initcall+0x61/0x250
 do_init_module+0x8a/0x270
 init_module_from_file+0x8b/0xd0
 idempotent_init_module+0x17d/0x230
 __x64_sys_finit_module+0x61/0xb0
 do_syscall_64+0x71/0x140
 entry_SYSCALL_64_after_hwframe+0x46/0x4e
 </TASK>

Fixes: 8bf30be7 ("net/mlx5e: Introduce select queue parameters")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-8-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Changing the channels number after configuring the receive flow hash
indirection table may affect the RSS table size. The previous
configuration may no longer be compatible with the new receive flow
hash indirection table.

Block changing the channels number when RXFH is configured and changing
the channels number requires resizing the RSS table size.

Fixes: 74a8dada ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-7-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

struct mlx5_pkt_reformat contains a naked union of a u32 id and a
dr_action pointer which is used when the action is SW-managed (when
pkt_reformat.owner is set to MLX5_FLOW_RESOURCE_OWNER_SW). Using id
directly in that case is incorrect, as it maps to the least significant
32 bits of the 64-bit pointer in mlx5_fs_dr_action and not to the pkt
reformat id allocated in firmware.

For the purpose of comparing whether two rules are identical,
interpreting the least significant 32 bits of the mlx5_fs_dr_action
pointer as an id mostly works... until it breaks horribly and produces
the outcome described in [1].

This patch fixes mlx5_flow_dests_cmp to correctly compare ids using
mlx5_fs_dr_action_get_pkt_reformat_id for the SW-managed rules.

Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]

Fixes: 6a48faee ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-6-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Previously, add_rule_fg would only add newly created rules from the
handle into the tree when they had a refcount of 1. On the other hand,
create_flow_handle tries hard to find and reference already existing
identical rules instead of creating new ones.

These two behaviors can result in a situation where create_flow_handle
1) creates a new rule and references it, then
2) in a subsequent step during the same handle creation references it
   again,
resulting in a rule with a refcount of 2 that is not linked into the
tree, will have a NULL parent and root and will result in a crash when
the flow group is deleted because del_sw_hw_rule, invoked on rule
deletion, assumes node->parent is != NULL.

This happened in the wild, due to another bug related to incorrect
handling of duplicate pkt_reformat ids, which lead to the code in
create_flow_handle incorrectly referencing a just-added rule in the same
flow handle, resulting in the problem described above. Full details are
at [1].

This patch changes add_rule_fg to add new rules without parents into
the tree, properly initializing them and avoiding the crash. This makes
it more consistent with how rules are added to an FTE in
create_flow_handle.

Fixes: 74491de9 ("net/mlx5: Add multi dest support")
Link: https://lore.kernel.org/netdev/ea5264d6-6b55-4449-a602-214c6f509c1e@163.com/T/#u [1]
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-5-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The mlx5 comp irq name scheme is changed a little bit between
commit 3663ad34 ("net/mlx5: Shift control IRQ to the last index")
and commit 3354822c ("net/mlx5: Use dynamic msix vectors allocation").
The index in the comp irq name used to start from 0 but now it starts
from 1. There is nothing critical here, but it's harmless to change
back to the old behavior, a.k.a starting from 0.

Fixes: 3354822c ("net/mlx5: Use dynamic msix vectors allocation")
Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reviewed-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Michael Liang <mliang@purestorage.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-4-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In case device is having a non fatal FW error during probe, the
driver will report the error to user via devlink. This will trigger
a WARN_ON, since mlx5 is calling devlink_register() last.
In order to avoid the WARN_ON[1], change mlx5 to invoke devl_register()
first under devlink lock.

[1]
WARNING: CPU: 5 PID: 227 at net/devlink/health.c:483 devlink_recover_notify.constprop.0+0xb8/0xc0
CPU: 5 PID: 227 Comm: kworker/u16:3 Not tainted 6.4.0-rc5_for_upstream_min_debug_2023_06_12_12_38 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_health0000:08:00.0 mlx5_fw_reporter_err_work [mlx5_core]
RIP: 0010:devlink_recover_notify.constprop.0+0xb8/0xc0
Call Trace:
 <TASK>
 ? __warn+0x79/0x120
 ? devlink_recover_notify.constprop.0+0xb8/0xc0
 ? report_bug+0x17c/0x190
 ? handle_bug+0x3c/0x60
 ? exc_invalid_op+0x14/0x70
 ? asm_exc_invalid_op+0x16/0x20
 ? devlink_recover_notify.constprop.0+0xb8/0xc0
 devlink_health_report+0x4a/0x1c0
 mlx5_fw_reporter_err_work+0xa4/0xd0 [mlx5_core]
 process_one_work+0x1bb/0x3c0
 ? process_one_work+0x3c0/0x3c0
 worker_thread+0x4d/0x3c0
 ? process_one_work+0x3c0/0x3c0
 kthread+0xc6/0xf0
 ? kthread_complete_and_exit+0x20/0x20
 ret_from_fork+0x1f/0x30
 </TASK>

Fixes: cf530217 ("devlink: Notify users when objects are accessible")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-3-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Next patch will move devlink register to be first. Therefore, whenever
mlx5 will register a param, the user will be notified.
In order to notify the user, devlink is using the get() callback of
the param. Hence, resources that are being used by the get() callback
must be set before the devlink param is registered.

Therefore, store eswitch pointer inside mdev before registering the
param.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240409190820.227554-2-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>