Swap branches of the if statement in order to simplify it's logical
condition being checked. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Use a local "struct spi_bitbang *bb" in spi_gpio_probe() for
brevity. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Use a local "struct device *dev" in spi_gpio_probe() for brevity. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Spi_to_pdata() is not used anywhere in the code. Drop it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>

Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.

So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Setup gpio-cs to the correct levels during setup and also make the
gpio definitely an output GPIO.

This is transparently fixing some badly configured DTs in the process
where cs-gpio is set but the gpios are still configured with native cs.

It also makes 100% sure that the initial CS levels are as expected -
especially on systems with devices on a bus with mixed CS_HIGH/CS_LOW
settings.

Fixes: 1ea29b39 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

From personal bad experience (even as the author of the original driver)
it shows that native-cs is "somewhat" supported by the spi bus driver
when using a buggy device tree.

So make sure that the driver is warning in dmesg about this fact
that we are running in a not supported mode that may have surprizing
limitations.

Fixes: 1ea29b39 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The original driver by default defines num_chipselects as -1.
This actually allicates an array of 65535 entries in
of_spi_register_master.

There is a side-effect for buggy device trees that (contrary to
dt-binding documentation) have no cs-gpio defined.

This mode was never supported by the driver due to limitations
of native cs and additional code complexity and is explicitly
not stated to be implemented.

To keep backwards compatibility with such buggy DTs we limit
the number of chip_selects to 1, as for all practical purposes
it is only ever realistic to use a single chip select in
native cs mode without negative side-effects.

Fixes: 1ea29b39 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove dead code that never can get reached, as we limit count to
a max of 3.
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

On long running tests with a mcp2517fd can controller it showed that
on rare occations the data read shows corruptions for longer spi transfers.

Example of a 22 byte transfer:

expected (as captured on logic analyzer):
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 85 86 87 88 89 8a 8b

read by the driver:
FF FF 78 00 00 00 08 06 00 00 91 20 77 56 84 88 89 8a 00 00 8b 9b

To fix this use BCM2835_AUX_SPI_STAT_RX_LVL to determine when we may
read data from the fifo reliably without any corruption.

Surprisingly the only values ever empirically read in
BCM2835_AUX_SPI_STAT_RX_LVL are 0x00, 0x10, 0x20 and 0x30.
So whenever the mask is not 0 we can read from the fifo in a safe manner.

The patch has now been tested intensively and we are no longer
able to reproduce the "RX" issue any longer.

Fixes: 1ea29b39 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Reported-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This read of the fifo is a potential candidate for a race condition
as the spi transfer is not necessarily finished and so can lead to
an early read of the fifo that still misses data.

So it has been removed.

Fixes: 1ea29b39 ("spi: bcm2835aux: add bcm2835 auxiliary spi device...")
Suggested-by: Hubert Denkmair <h.denkmair@intence.de>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Sharing more code between polling and interrupt-driven mode.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Export spi_mem_default_supports_op(), so that controller drivers
can use this.
spi-mem driver already exports this using EXPORT_SYMBOL,
but not declared it in spi-mem.h.
This patch declares spi_mem_default_supports_op() in spi-mem.h and
also removes the static from the function prototype.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Improve maintainability by converting the register bit, bitmask, and
bitfield definitions from hexadecimal constants to constructs using
BIT(), GENMASK(), or "val << shift".
Suggested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit c9bfcb31 (spi_mpc83xx: much improved driver) introduced
logic to ensure bits_per_word and speed_hz stay the same for a series
of spi_transfers with CS active, arguing that

    The current driver may cause glitches on SPI CLK line since one
    must disable the SPI controller before changing any HW settings.

This sounds quite reasonable. So this is a quite naive attempt at
relaxing this sanity checking to only ensure that speed_hz is
constant - in the faint hope that if we do not causes changes to the
clock-related fields of the SPMODE register (DIV16 and PM), those
glitches won't appear.

The purpose of this change is to allow automatically optimizing large
transfers to use 32 bits-per-word; taking one interrupt for every byte
is extremely slow.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use SPI device pointer in the remaining two error and warning prints in
pxa2xx_spi_transfer_one() instead of platform device of the controller

It make prints in the function uniform and more useful especially the
error print here as it can reveal the driver that has mapped the DMA
itself and attempts to transfer more than the maximum supported DMA
transfer length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there
is no need to access it through the current SPI message pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Tegra SPI controller supports lsb first mode. Default is MSB bit first
and on selection of SPI_LSB_FIRST through SPI mode transmission happens
with LSB bit first.

This patch adds SPI_LSB_FIRST flag to mode_bits and also configures it
on request.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: Use packed mode for 32 bits per word transfers to increase
performance as each packet is a full 32-bit word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The comment says that we should not allow changes (to
bits_per_word/speed_hz) while CS is active, and indeed the code below
does fsl_spi_setup_transfer() when the ->cs_change of the previous
spi_transfer was set (and for the very first transfer).

So the sanity checking is a bit too strict - we can change it to
follow the same logic as is used by the actual transfer loop.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

__spi_validate() in the generic SPI code sets ->speed_hz and
->bits_per_word to non-zero values, so this condition is always true.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds the dma support for the stm32-qspi hardware.
The memory buffer constraints (lowmem, vmalloc, kmap) are taken into
account by framework. In read mode, the memory map is preferred vs
dma (due to better throughput). If the dma transfer fails the buffer
is sent by polling.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds spi_master_put in release function
to drop the controller's refcount.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.

This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).

This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This checking is already done in __spi_validate_bits_per_word().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix sparse warning:

drivers/spi/atmel-quadspi.c:369:12: warning:
 symbol 'atmel_qspi_get_name' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The newly added tracepoints in the spi-mxs driver cause a link
error when the driver is a loadable module:

ERROR: "__tracepoint_spi_transfer_stop" [drivers/spi/spi-mxs.ko] undefined!
ERROR: "__tracepoint_spi_transfer_start" [drivers/spi/spi-mxs.ko] undefined!

I'm not quite sure where to put the export statements, but
directly after the inclusion of the header seems as good as
any other place.

Fixes: f3fdea3a ("spi: mxs: add tracing to custom .transfer_one_message callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

It's useful during debug to see what DMA burst size is.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some masters may have different DMA burst size than hard coded default.
In such case respect the value given by DMA burst size provided via
platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Synopsys SSI Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add support
for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add documentation to the Synopsys SPI dt-bindings to support an
optional interface clock that may be used for register access.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Synopsys SSI driver uses a mandatory clock that is not documented,
so detail it in the device tree bindings. Also correct the spelling of
"pins" in the "Optional Properties" section for the driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 2e541b64 ("spi: spi-mem: stm32-qspi: add suspend/resume support")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.1-rc1

There is nothing in the driver which requires OF specific header
to be included.

Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The MPC8309 has a dedicated signal, SPISEL_BOOT, usually used as chip
select for the flash device from which the bootloader is loaded. It is
not an ordinary gpio, but is simply controlled via the SPI_CS register
in the system configuration.

To allow accessing such a spi slave, we need to teach
fsl_spi_cs_control() how to control the SPISEL_BOOT signal. To
distinguish the gpio-controlled slaves, continue to have those use
chip_select values of 0..ngpios-1, and use chip_select == ngpios for
the boot flash.

I'm not too happy with all the ifdeffery, but it seems to be necessary
for guarding the sysdev/fsl_soc.h and use of
get_immrbase() (spi-fsl-lib.c already contains similar ifdeffery).

Googling suggests that the MPC8306 is similar, with the SPI_CS
register at the same offset.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>