- 13 Apr, 2018 40 commits
-
-
Mikko Koivunen authored
[ Upstream commit 12d74949 ] Set sensor measurement off after probe fail in pm_runtime_set_active() or iio_device_register(). Without this change sensor measurement stays on even though probe fails on these calls. This is maybe rare case, but causes constant power drain without any benefits when it happens. Power drain is 20-500uA, typically 180uA. Signed-off-by:
Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com> Acked-by:
Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nikita Yushchenko authored
[ Upstream commit 61305664 ] Reset GPIO is active low. Currently driver uses gpiod_set_value(1) to clean reset, which depends on device tree to contain GPIO_ACTIVE_HIGH - that does not match reality. This fixes driver to use _raw version of gpiod_set_value() to enforce active-low semantics despite of what's written in device tree. Allowing device tree to override that only opens possibility for errors and does not add any value. Additionally, use _cansleep version to make things work with i2c-gpio and other sleeping gpio drivers. Signed-off-by:
Nikita Yushchenko <nikita.yoush@cogentembedded.com> Signed-off-by:
-
Nikita Yushchenko authored
[ Upstream commit ee19ac34 ] Currently, driver generates events for channels if new reading differs from previous one. This "previous value" is initialized to zero, which results into event if value is constant-one. Fix that by initializing "previous value" by reading at event enable time. This provides reliable sequence for userspace: - enable event, - AFTER THAT read current value, - AFTER THAT each event will correspond to change. Signed-off-by:
-
Stefan Agner authored
[ Upstream commit f746aa5e ] Initialize asoc_simple_card_init_mic with the correct struct asoc_simple_jack. Fixes: 9eac3618 ("ASoC: simple-card: add new asoc_simple_jack and use it") Signed-off-by:
Stefan Agner <stefan@agner.ch> Acked-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Antony Antony authored
[ Upstream commit a486cd23 ] During xfrm migration copy replay and preplay sequence numbers from the previous state. Here is a tcpdump output showing the problem. 10.0.10.46 is running vanilla kernel, is the IKE/IPsec responder. After the migration it sent wrong sequence number, reset to 1. The migration is from 10.0.0.52 to 10.0.0.53. IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7cf), length 136 IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7cf), length 136 IP 10.0.0.52.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d0), length 136 IP 10.0.10.46.4500 > 10.0.0.52.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x7d0), length 136 IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I] IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R] IP 10.0.0.53.4500 > 10.0.10.46.4500: NONESP-encap: isakmp: child_sa inf2[I] IP 10.0.10.46.4500 > 10.0.0.53.4500: NONESP-encap: isakmp: child_sa inf2[R] IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d1), length 136 NOTE: next sequence is wrong 0x1 IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x1), length 136 IP 10.0.0.53.4500 > 10.0.10.46.4500: UDP-encap: ESP(spi=0x43ef462d,seq=0x7d2), length 136 IP 10.0.10.46.4500 > 10.0.0.53.4500: UDP-encap: ESP(spi=0xca1c282d,seq=0x2), length 136 Signed-off-by:
Antony Antony <antony@phenome.org> Reviewed-by:
Richard Guy Briggs <rgb@tricolour.ca> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit fe06fe86 ] The tm-resched-dscr test has started failing sometimes, depending on what compiler it's built with, eg: test: tm_resched_dscr Check DSCR TM context switch: tm-resched-dscr: tm-resched-dscr.c:76: test_body: Assertion `rv' failed. !! child died by signal 6 When it fails we see that the compiler doesn't initialise rv to 1 before entering the inline asm block. Although that's counter intuitive, it is allowed because we tell the compiler that the inline asm will write to rv (using "=r"), meaning the original value is irrelevant. Marking it as a read/write parameter would presumably work, but it seems simpler to fix it by setting the initial value of rv in the inline asm. Fixes: 96d01610 ("powerpc: Correct DSCR during TM context switch") Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Acked-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 8fed6823 ] The AR5K_EEPROM_READ macro returns with -EIO if a read error occurs causing a memory leak on the allocated buffer buf. Fix this by explicitly calling ath5k_hw_nvram_read and exiting on the via the freebuf label that performs the necessary free'ing of buf when a read error occurs. Detected by CoverityScan, CID#1248782 ("Resource Leak") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit e41e53cd ] virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on an address. What this means in practice is that it should only return true for addresses in the linear mapping which are backed by a valid PFN. We are failing to properly check that the address is in the linear mapping, because virt_to_pfn() will return a valid looking PFN for more or less any address. That bug is actually caused by __pa(), used in virt_to_pfn(). eg: __pa(0xc000000000010000) = 0x10000 # Good __pa(0xd000000000010000) = 0x10000 # Bad! __pa(0x0000000000010000) = 0x10000 # Bad! This started happening after commit bdbc29c1 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give you something bogus back. Until we can verify if that GCC bug is no longer an issue, or come up with another solution, this commit does the minimal fix to make virt_addr_valid() work, by explicitly checking that the address is in the linear mapping region. Fixes: bdbc29c1 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit") Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Reviewed-by:
Balbir Singh <bsingharora@gmail.com> Tested-by:
Breno Leitao <breno.leitao@gmail.com> Signed-off-by:
-
Varun Prakash authored
[ Upstream commit a351e40b ] mbp pointer is passed to csio_hw_validate_caps() so call mempool_free() after calling csio_hw_validate_caps(). Signed-off-by:
Varun Prakash <varun@chelsio.com> Fixes: 541c571f ("csiostor:Use firmware version from cxgb4/t4fw_version.h") Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Ido Schimmel authored
[ Upstream commit c0e01eac ] In case we got an FDB notification for a port that doesn't exist we execute an FDB entry delete to prevent it from re-appearing the next time we poll for notifications. If the operation failed we would trigger a NULL pointer dereference as 'mlxsw_sp_port' is NULL. Fix it by reporting the error using the underlying bus device instead. Fixes: 12f1501e ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification") Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 5f5c5449 ] The MDIO initialization failure message is printed using the network device, before it has been registered, leading to: (null): failed to initialise MDIO Use the platform device instead to fix this: sh-eth ee700000.ethernet: failed to initialise MDIO Fixes: daacf03f ("sh_eth: Register MDIO bus before registering the network device") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Holger Brunck authored
[ Upstream commit c7f235a7 ] Add the bitmask for the two bit SYNL register according to the QUICK Engine Reference Manual. Signed-off-by:
Holger Brunck <holger.brunck@keymile.com> Cc: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by:
-
Holger Brunck authored
[ Upstream commit 5b8aad93 ] We need space for the struct qe_bd and not for a pointer to this struct. Signed-off-by:
-
Holger Brunck authored
[ Upstream commit 66bb144b ] This fixes the following compiler warnings: drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_poll': warning: 'skb' may be used uninitialized in this function [-Wmaybe-uninitialized] skb->mac_header = skb->data - skb->head; and drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_probe': drivers/net/wan/fsl_ucc_hdlc.c:1127:3: warning: 'utdm' may be used uninitialized in this function [-Wmaybe-uninitialized] kfree(utdm); Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 1cf4a7ef ] If DMA is enabled and used, a burst of old data may be seen on the serial console during "poweroff" or "reboot". uart_flush_buffer() clears the circular buffer, but sci_port.tx_dma_len is not reset. This leads to a circular buffer overflow, dumping (UART_XMIT_SIZE - sci_port.tx_dma_len) bytes. To fix this, add a .flush_buffer() callback that resets sci_port.tx_dma_len. Inspired by commit 31ca2c63 ("tty/serial: atmel: fix race condition (TX+DMA)"). Signed-off-by:
-
Vignesh R authored
[ Upstream commit 84b40e3b ] Kernel always writes log messages to console via serial8250_console_write()->serial8250_console_putchar() which directly accesses UART_TX register _without_ using DMA. But, if other processes like systemd using same UART port, then these writes are handled by a different code flow using 8250_omap driver where there is provision to use DMA. It seems that it is possible that both DMA and CPU might simultaneously put data to UART FIFO and lead to potential loss of data due to FIFO overflow and weird data corruption. This happens when both kernel console and userspace tries to write simultaneously to the same UART port. Therefore, disable DMA on kernel console port to avoid potential race between CPU and DMA. Signed-off-by:
Vignesh R <vigneshr@ti.com> Signed-off-by:
-
Alan Stern authored
[ Upstream commit aa18c4b6 ] In the ene_usb6250 sub-driver for usb-storage, the SCSI residue is not reported correctly. The residue is initialized to 0, but this value is overwritten whenever the driver sends firmware to the card reader before performing the current command. As a result, a valid READ or WRITE operation appears to have failed, causing the SCSI core to retry the command multiple times and eventually fail. This patch fixes the problem by resetting the SCSI residue to 0 after sending firmware to the device. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by:
Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by:
-
linzhang authored
[ Upstream commit 64df6d52 ] The function x25_init is not properly unregister related resources on error handler.It is will result in kernel oops if x25_init init failed, so add properly unregister call on error handler. Also, i adjust the coding style and make x25_register_sysctl properly return failure. Signed-off-by:
linzhang <xiaolou4617@gmail.com> Signed-off-by:
-
Alan Stern authored
[ Upstream commit 4b309f1c ] In the ene_usb6250 sub-driver for usb-storage, the ene_transport() routine is supposed to initialize the driver before executing the current command, if the initialization has not already been performed. However, a bug in the routine causes it to skip the command after doing the initialization. Also, the routine does not return an appropriate error code if either the initialization or the command fails. As a result of the first bug, the first command (a SCSI INQUIRY) is not carried out. The results can be seen in the system log, in the form of a warning message and empty or garbage INQUIRY data: Apr 18 22:40:08 notebook2 kernel: scsi host6: scsi scan: INQUIRY result too short (5), using 36 Apr 18 22:40:08 notebook2 kernel: scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 0 This patch fixes both errors. Signed-off-by:
-
Petr Cvek authored
[ Upstream commit e3b4d10c ] The conversion from soc_camera omitted a correct handling of the clock gating for a sensor. When the pxa_camera driver module was removed it tried to unregister clk, but this caused a similar warning: WARNING: CPU: 0 PID: 6740 at drivers/media/v4l2-core/v4l2-clk.c:278 v4l2_clk_unregister(): Refusing to unregister ref-counted 0-0030 clock! The clock was at time still refcounted by the sensor driver. Before the removing of the pxa_camera the clock must be dropped by the sensor driver. This should be triggered by v4l2_async_notifier_unregister() call which removes sensor driver module too, calls unbind() function and then tries to probe sensor driver again. Inside unbind() we can safely unregister the v4l2 clock as the sensor driver got removed. The original v4l2_clk_unregister() should be put inside test as the clock can be already unregistered from unbind(). If there was not any bound sensor the clock is still present. The codepath is practically a copy from the old soc_camera. The bug was tested with a pxa_camera+ov9640 combination during the conversion of the ov9640 from the soc_camera. Signed-off-by:
Petr Cvek <petr.cvek@tul.cz> Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Jisheng Zhang authored
[ Upstream commit c4a0bbbd ] If ci_hdrc_host_init() or ci_hdrc_gadget_init() returns error and the error != -ENXIO, as Peter pointed out, "it stands for initialization for host or gadget has failed", so we'd better return failure rather continue. And before destroying the otg, i.e ci_hdrc_otg_destroy(ci), we should also check ci->roles[CI_ROLE_GADGET]. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Sugar Zhang authored
[ Upstream commit 9d420e9b ] Refer to Chapter 5.3.2 of rk3229 TRM, we can see that GPIO1A[2,4,5] using RK_FUNC_2 not RK_FUNC_1. This patch fixes it. Signed-off-by:
Sugar Zhang <sugar.zhang@rock-chips.com> Signed-off-by:
Frank Wang <frank.wang@rock-chips.com> Signed-off-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Ihar Hrachyshka authored
[ Upstream commit 23d268eb ] When arp_accept is 1, gratuitous ARPs are supposed to override matching entries irrespective of whether they arrive during locktime. This was implemented in commit 56022a8f ("ipv4: arp: update neighbour address when a gratuitous arp is received and arp_accept is set") There is a glitch in the patch though. RFC 2002, section 4.6, "ARP, Proxy ARP, and Gratuitous ARP", defines gratuitous ARPs so that they can be either of Request or Reply type. Those Reply gratuitous ARPs can be triggered with standard tooling, for example, arping -A option does just that. This patch fixes the glitch, making both Request and Reply flavours of gratuitous ARPs to behave identically. As per RFC, if gratuitous ARPs are of Reply type, their Target Hardware Address field should also be set to the link-layer address to which this cache entry should be updated. The field is present in ARP over Ethernet but not in IEEE 1394. In this patch, I don't consider any broadcasted ARP replies as gratuitous if the field is not present, to conform the standard. It's not clear whether there is such a thing for IEEE 1394 as a gratuitous ARP reply; until it's cleared up, we will ignore such broadcasts. Note that they will still update existing ARP cache entries, assuming they arrive out of locktime time interval. Signed-off-by:
Ihar Hrachyshka <ihrachys@redhat.com> Signed-off-by:
-
Ihar Hrachyshka authored
[ Upstream commit 77d71233 ] It's a common practice to send gratuitous ARPs after moving an IP address to another device to speed up healing of a service. To fulfill service availability constraints, the timing of network peers updating their caches to point to a new location of an IP address can be particularly important. Sometimes neigh_update calls won't touch neither lladdr nor state, for example if an update arrives in locktime interval. The neigh->updated value is tested by the protocol specific neigh code, which in turn will influence whether NEIGH_UPDATE_F_OVERRIDE gets set in the call to neigh_update() or not. As a result, we may effectively ignore the update request, bailing out of touching the neigh entry, except that we still bump its timestamps inside neigh_update. This may be a problem for updates arriving in quick succession. For example, consider the following scenario: A service is moved to another device with its IP address. The new device sends three gratuitous ARP requests into the network with ~1 seconds interval between them. Just before the first request arrives to one of network peer nodes, its neigh entry for the IP address transitions from STALE to DELAY. This transition, among other things, updates neigh->updated. Once the kernel receives the first gratuitous ARP, it ignores it because its arrival time is inside the locktime interval. The kernel still bumps neigh->updated. Then the second gratuitous ARP request arrives, and it's also ignored because it's still in the (new) locktime interval. Same happens for the third request. The node eventually heals itself (after delay_first_probe_time seconds since the initial transition to DELAY state), but it just wasted some time and require a new ARP request/reply round trip. This unfortunate behaviour both puts more load on the network, as well as reduces service availability. This patch changes neigh_update so that it bumps neigh->updated (as well as neigh->confirmed) only once we are sure that either lladdr or entry state will change). In the scenario described above, it means that the second gratuitous ARP request will actually update the entry lladdr. Ideally, we would update the neigh entry on the very first gratuitous ARP request. The locktime mechanism is designed to ignore ARP updates in a short timeframe after a previous ARP update was honoured by the kernel layer. This would require tracking timestamps for state transitions separately from timestamps when actual updates are received. This would probably involve changes in neighbour struct. Therefore, the patch doesn't tackle the issue of the first gratuitous APR ignored, leaving it for a follow-up. Signed-off-by:
-
Suman Anna authored
[ Upstream commit 0d835390 ] Commit 75f0aef6 ("uio: fix memory leak") has fixed up some memory leaks during the failure paths of the addition of uio attributes, but still is not correct entirely. A kobject_uevent() failure still needs a kobject_put() and the kobject container structure allocation failure before the kobject_init() doesn't need a kobject_put(). Fix this properly. Fixes: 75f0aef6 ("uio: fix memory leak") Signed-off-by:
Suman Anna <s-anna@ti.com> Signed-off-by:
-
Thomas Winter authored
[ Upstream commit bcfc7d33 ] The skb->dev that is passed into ip_mr_input is the loX device for VRFs. When we lookup a vif for this dev, none is found as we do not create vifs for loopbacks. Instead lookup a vif for the actual device that the packet was received on, eg the vlan. Signed-off-by:
Thomas Winter <Thomas.Winter@alliedtelesis.co.nz> cc: David Ahern <dsa@cumulusnetworks.com> cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> cc: roopa <roopa@cumulusnetworks.com> Acked-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Thomas Petazzoni authored
[ Upstream commit c034640a ] When platform_get_irq() fails, it returns an error code, which libahci_platform and replaces it by -EINVAL. This commit fixes that by propagating the error code. It fixes the situation where platform_get_irq() returns -EPROBE_DEFER because the interrupt controller is not available yet, and generally looks like the right thing to do. We pay attention to not show the "no irq" message when we are in an EPROBE_DEFER situation, because the driver probing will be retried later on, once the interrupt controller becomes available to provide the interrupt. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit bff5baf8 ] The setting of return code ret should be based on the error code passed into function end_extent_writepage and not on ret. Thanks to Liu Bo for spotting this mistake in the original fix I submitted. Detected by CoverityScan, CID#1414312 ("Logically dead code") Fixes: 5dca6eea ("Btrfs: mark mapping with error flag to report errors to userspace") Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Pan Bian authored
[ Upstream commit 018047a1 ] Function devm_clk_get() returns an ERR_PTR when it fails. However, in function kdwc3_probe(), its return value is not checked, which may result in a bad memory access bug. This patch fixes the bug. Signed-off-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
James Morse authored
[ Upstream commit e8ec032b ] When KVM panics, it hurridly restores the host context and parachutes into the host's panic() code. At some point panic() touches the physical timer/counter. Unless we are an arm64 system with VHE, this traps back to EL2. If we're lucky, we panic again. Add a __timer_save_state() call to KVMs hyp_panic() path, this saves the guest registers and disables the traps for the host. Fixes: 53fd5b64 ("arm64: KVM: Add panic handling") Signed-off-by:
James Morse <james.morse@arm.com> Reviewed-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
James Morse authored
[ Upstream commit d2e19368 ] When KVM panics, it hurridly restores the host context and parachutes into the host's panic() code. This looks like it was copied from arm64, the 32bit KVM panic code needs to restore the host's banked registers too. At some point panic() touches the physical timer/counter, this will trap back to HYP. If we're lucky, we panic again. Add a __timer_save_state() call to KVMs hyp_panic() path, this saves the guest registers and disables the traps for the host. Fixes: c36b6db5 ("ARM: KVM: Add panic handling code") Signed-off-by:
-
Anup Patel authored
[ Upstream commit baae03a0 ] The DMA_PREP_FENCE is to be used when preparing Tx descriptor if output of Tx descriptor is to be used by next/dependent Tx descriptor. The DMA_PREP_FENSE will not be set correctly in do_async_gen_syndrome() when calling dma->device_prep_dma_pq() under following conditions: 1. ASYNC_TX_FENCE not set in submit->flags 2. DMA_PREP_FENCE not set in dma_flags 3. src_cnt (= (disks - 2)) is greater than dma_maxpq(dma, dma_flags) This patch fixes DMA_PREP_FENCE usage in do_async_gen_syndrome() taking inspiration from do_async_xor() implementation. Signed-off-by:
Anup Patel <anup.patel@broadcom.com> Reviewed-by:
Ray Jui <ray.jui@broadcom.com> Reviewed-by:
Scott Branden <scott.branden@broadcom.com> Acked-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Mahesh Bandewar authored
[ Upstream commit 66eb9f86 ] Every address gets added with TENTATIVE flag even for the addresses with IFA_F_NODAD flag and dad-work is scheduled for them. During this DAD process we realize it's an address with NODAD and complete the process without sending any probe. However the TENTATIVE flags stays on the address for sometime enough to cause misinterpretation when we receive a NS. While processing NS, if the address has TENTATIVE flag, we mark it DADFAILED and endup with an address that was originally configured as NODAD with DADFAILED. We can't avoid scheduling dad_work for addresses with NODAD but we can avoid adding TENTATIVE flag to avoid this racy situation. Signed-off-by:
Mahesh Bandewar <maheshb@google.com> Acked-by:
-
Julia Lawall authored
[ Upstream commit 8c977f5a ] Device node iterators put the previous value of the index variable, so an explicit put causes a double put. In particular, of_mdiobus_register can fail before doing anything interesting, so one could view it as a no-op from the reference count point of view. Generated by: scripts/coccinelle/iterators/device_node_continue.cocci CC: Jon Mason <jon.mason@broadcom.com> Signed-off-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Ganapatrao Kulkarni authored
[ Upstream commit 78a19cfd ] commit d98ecdac ("arm64: perf: Count EL2 events if the kernel is running in HYP") returns -EINVAL when perf system call perf_event_open is called with exclude_hv != exclude_kernel. This change breaks applications on VHE enabled ARMv8.1 platforms. The issue was observed with HHVM application, which calls perf_event_open with exclude_hv = 1 and exclude_kernel = 0. There is no separate hypervisor privilege level when VHE is enabled, the host kernel runs at EL2. So when VHE is enabled, we should ignore exclude_hv from the application. This behaviour is consistent with PowerPC where the exclude_hv is ignored when the hypervisor is not present and with x86 where this flag is ignored. Signed-off-by:
Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com> [will: added comment to justify the behaviour of exclude_hv] Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Peter Rosin authored
[ Upstream commit 68118e0e ] It is only prudent to let go of resources that are not used. Fixes: b3fdd327 ("i2c: mux: Add register-based mux i2c-mux-reg") Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
-
Fabio Estevam authored
[ Upstream commit 79935915 ] When running a stress playback/stop loop test on a mx6wandboard channel swaps can be noticed randomly. Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes the issue, so add the 'lrclk-strength' property to avoid the audio channel swaps. Signed-off-by:
Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit 43e24e82 ] On powerpc we can build the kernel with two different ABIs for mcount(), which is used by ftrace. Kernels built with one ABI do not know how to load modules built with the other ABI. The new style ABI is called "mprofile-kernel", for want of a better name. Currently if we build a module using the old style ABI, and the kernel with mprofile-kernel, when we load the module we'll oops something like: # insmod autofs4-no-mprofile-kernel.ko ftrace-powerpc: Unexpected instruction f8810028 around bl _mcount ------------[ cut here ]------------ WARNING: CPU: 6 PID: 3759 at ../kernel/trace/ftrace.c:2024 ftrace_bug+0x2b8/0x3c0 CPU: 6 PID: 3759 Comm: insmod Not tainted 4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 #11 ... NIP [c0000000001eaa48] ftrace_bug+0x2b8/0x3c0 LR [c0000000001eaff8] ftrace_process_locs+0x4a8/0x590 Call Trace: alloc_pages_current+0xc4/0x1d0 (unreliable) ftrace_process_locs+0x4a8/0x590 load_module+0x1c8c/0x28f0 SyS_finit_module+0x110/0x140 system_call+0x38/0xfc ... ftrace failed to modify [<d000000002a31024>] 0xd000000002a31024 actual: 35:65:00:48 We can avoid this by including in the vermagic whether the kernel/module was built with mprofile-kernel. Which results in: # insmod autofs4-pg.ko autofs4: version magic '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74 SMP mod_unload modversions ' should be '4.11.0-rc3-gcc-5.4.1-00017-g5a61ef74-dirty SMP mod_unload modversions mprofile-kernel' insmod: ERROR: could not insert module autofs4-pg.ko: Invalid module format Fixes: 8c50b72a ("powerpc/ftrace: Add Kconfig & Make glue for mprofile-kernel") Signed-off-by:
Jessica Yu <jeyu@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 8309f86c ] Since the clocksource watchdog will only detect broken TSC after the fact, all TSC based clocks will likely have observed non-continuous values before/when switching away from TSC. Therefore only thing to fully avoid random clock movement when your BIOS randomly mucks with TSC values from SMI handlers is reporting the TSC as unstable at boot. Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit b7c563c4 ] R-Car V2H and E2 do not have the PLL0CR register, but use a fixed multiplier (depending on mode pins) and divider. This corrects the clock rate of "pll0" (PLL0 VCO after post divider) on R-Car V2H and E2 from 1.5 GHz to 1 GHz. Inspired by Sergei Shtylyov's work for the common R-Car Gen2 and RZ/G Clock Pulse Generator support core. Fixes: 7c4163aa ("ARM: dts: r8a7792: initial SoC device tree") Fixes: 0dce5454 ("ARM: shmobile: Initial r8a7794 SoC device tree") Signed-off-by:
-
