The number of CSI TX lanes is hardcoded to 4. Removing
this and start using value from configure stream response.

NOTE: The patch depends on the CSI init change:
"Use GB CSI params to init camera sub-devs"
Signed-off-by: Evgeniy Borisov <eborisov@mm-sol.com>
Reviewed-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This change adds the AP Power Monitor functions to
read out all the rails power information monitored by
the SVC.

Testing Done:
- $ cat /d/greybus/1-svc/pwrmon/*/*
  and validate the output with the svc stub power
  monitor functions
- $ tree /d/greybus/1-svc/pwrmon
  | | | |---pwrmon
  | | | | |---DUMMY_RAIL_1
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_2
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_3
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
  | | | | |---DUMMY_RAIL_4
  | | | | | |---current_now
  | | | | | |---power_now
  | | | | | |---voltage_now
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Read on apb_log causes null pointer exception due to the missing es2
device pointer passing to the debugfs.

Testing done:
- Enable apb_log and cat it
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The check for line coding changed should use memcmp and not memcpy.

Testing done: trivial
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove unnecessary interface-remove helper.

Also add comment about why the disconnected flag is set.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Keep a detected interface registered until it is physically removed.
Specifically, do not re-register an interface that is switching mode.

Note that this also allows us to get rid of some nasty hacks from core.
The Ara VID/PID bootrom hack for ES2 will continue to work, but is now
mostly confined to the bootrom driver.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to deactivate all interfaces when the svc is going away.

This is needed to eventually be able to do controlled teardown of the
unipro network.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make the control-device lifetime coincide with when the interface is
enabled (enumerated).

This is needed to be able register a new control device after a mode
switch.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Return an error pointer when failing to create a control device.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The control device is an abstraction of the control connection over
which a greybus manifest is retrieved. As interfaces switch modes (e.g.
after boot-over-unipro) they expose new manifests, which can contain
different vendor and product strings.

Eventually control devices will be deregistered and recreated after an
interface mode switch, while the interface itself remains registered.

Note that only interfaces of type greybus will have control devices.
Specifically, dummy interfaces will not.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make sure to register also the control device along with any bundles
when registering an interface.

Note that we currently ignore failures to register the control device
just as we do for bundle devices.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Make the control object be a greybus device.

The control device will be used to expose attributes specific to
greybus-type interfaces.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Move the timesync-operation functions above the control-object
management functions, which is where all other operation implementations
reside.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Disable and deactivate an interface immediately on registration
failures.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add control devices to the example sysfs tree.

Control devices are named

	<bus_id>-<module_id>.<intf_id>.ctrl

and expose attributes that are specific to the greybus interface type.
Specifically, dummy interfaces do not have a control device.

Currently, only the vendor and product strings extracted from the
manifest are exported.

A subtree of the example tree now looks as follows:

greybus1/
├── 1-5
│   ├── 1-5.5
│   │   ├── 1-5.5.2
│   │   │   ├── bundle_class
│   │   │   ├── bundle_id
│   │   │   └── state
│   │   ├── 1-5.5.ctrl
│   │   │   ├── product_string
│   │   │   └── vendor_string
│   │   ├── ddbl1_manufacturer_id
│   │   ├── ddbl1_product_id
│   │   ├── interface_id
│   │   ├── product_id
│   │   ├── serial_number
│   │   └── vendor_id
│   ├── 1-5.6
│   │   └── interface_id
│   ├── eject
│   ├── module_id
│   └── num_interfaces
└── 1-svc
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The svc eject attribute was added as an interim solution and is still
used to implement a form of forced ejection.

This will soon be superseded by the module eject attribute, which will
provide an interface for clean eject. We may keep the forced-eject
mechanism around indefinitely, albeit possibly with a different name
(e.g. forced_intf_eject). Either way, update the example tree to reflect
the actual name, intf_eject, which currently used for this svc attribute.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Remove the interface unique_id attribute, which there is currently no
plan to ever implement.

Note that the Ara serial numbers are already exposed through the
serial_number attribute.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Move the interface power attributes after the other interface attributes
to keep the attributes grouped by device type.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The manifest-parsing code could end up leaving the interface
vendor_string set to an error pointer that we'd eventually try to free
when destroying the interface.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

When transfer speed is too slow (less than 17Khz) the operation can take
longer than the default greybus timeout. Because of this we need to use
the request_send_sync_timeout and calculate the correct timeout for each
operation.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Tested-by: Philip Yang <philipy@bsquare.com>
Tested-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

The actual implementation of transfer_one_message have problems with
some cases in the possible transfer options. We try to maximize the
number of spi transfers in one greybus operation and need to save state
until the full message is dispatch over greybus.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Tested-by: Philip Yang <philipy@bsquare.com>
Tested-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

SVC watchdog should be disabled when device is entering suspend mode.

Testing done:
 - Sanity tested on EVT1.5
 - Check no SVC ping during the suspend process
 - Check SVC watchdog is back on pinging once device is resumed
Signed-off-by: David Lin <dtwlin@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: Removed unwanted check in notifier callback and
Updated commit description]
Tested-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Switch off APBs/SVC/Switch in the suspend call notifier. Note that
this is an interim solution to enable fishfooding.

Testing done:
 - Passed QA sanity test on EVT1.5
 - Suspend current measured at ~70mW
Signed-off-by: David Lin <dtwlin@google.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
[vaibhav.hiremath@linaro.org: Updated commit description]
Tested-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

A number of data in TimeSync command structures are declared __u64/__u32
instead of __le64/__le32, I forgot to put this through an x86_64 compile
before presentation for merge and as a result didn't catch this error. This
patch fixes.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Earlier during boot sequence implementation, we had seen race between
USb3613 and APB boot, and since APB boot time is ~2sec, we delayed
USb3613 configuration for 2sec after APB deassertion of reset.

This obviously won't work in the case of suspend/resume, where we would
like to put APB into OFF state and coldboot in resume.

With the latest FW changes, we do not see any race issue. I have done
regression testing (> 50 iteration of reboot + unipro link up and down)
without any issues.

So lets get rid of the 2sec delay with this patch.

Testing Done: Tested on EVT 1.5 platform.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: David Lin <dtwlin@google.com>
Reviewed-by: David Lin <dtwlin@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Extending the configure streams interface with CSI params.
Getting CSI frequency data form configure streams response.
 * num_lanes - Number of CSI data lanes
 * clk_freq - CSI clock frequency in Hz
 * lines_per_second - Total number of lines in a second of
transmission (blanking included)

From the AP side we need to know for the CSI speed
configuration. This information is needed for dynamically
bandwidth calculations.

NOTE: Change should be along merged with corresponding
      interface change in kernel:
      "camera: Extend the configure streams
      interface with CSI params"
Signed-off-by: Evgeniy Borisov <eborisov@mm-sol.com>
Reviewed-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This change implements the AP Power Monitor functions for obtaining
current/voltage/power on a specific rail of an Interface.

Testing Done:

$ cat /sys/bus/greybus/devices/1-3/current_now
103
$ cat /sys/bus/greybus/devices/1-3/power_now
303
$ cat /sys/bus/greybus/devices/1-3/voltage_now
203
Signed-off-by: David Lin <dtwlin@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Device type info shared to above HAL is currently hard coded
to SPK only. Actual device type is identifed while parsing
widget types from topology FW shared by codec module.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Currently, single field is used to report device type say SPK,
MIC, HS, HP, etc. However above HAL expects separate fields for
input & ouput device types.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Add support for greybus metadata format.
Greybus metadata format id is 0x41.
Signed-off-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Acked-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Align with Greybus specifications and rename Firmware Protocol driver as
Bootrom Protocol driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Don't know why, but checkpatch checks if we are running it from top of a
kernel tree or not, but then it also provides an option to suppress the
warning using --no-tree.

Instead of forcing everyone to use this every time, lets make this
behavior default.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

This reverts commit a1d8f2c3856804ed26157104bb203edf4c882a6c.

Added a sysfs entry called pwr_off. When a "1" is passed to it,
it sends a GB_SVC_TYPE_PWR_DOWN command to the SVC, powering it down
along with the switch and INA231 chips.

Testing Done: Tested on EVT1_5, works.
Signed-off-by: Georgi Dobrev <dobrev_georgi@projectara.com>

They belong in a subdir.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

For those who are stuck using old kernel trees, let's include the latest
version of checkpatch.pl into our tree to help prevent coding style
mistakes from creeping in.

Also add spelling.txt to catch spelling errors in comments.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Capture path related settings during startup, perpare &
hwparams were earlier missing.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

Register jack with ASoC sound card in case audio module
populates it via codec FW. Currently, only a single jack
with 4 buttons can be registered for each module.
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

widget pointer was incorrectly modfied while parsing kcontrol
Signed-off-by: Vaibhav Agarwal <vaibhav.agarwal@linaro.org>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>

No need to duplicate module ops on every registration.

NOTE: Change should be along merged with:
"msm: camera: Change gb_camera_module ops to pointer"
Signed-off-by: Gjorgji Rosikopulos <grosikopulos@mm-sol.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>