- 11 Jul, 2014 20 commits
-
-
Jan Kara authored
commit eeece469 upstream. Tail of a page straddling inode size must be zeroed when being written out due to POSIX requirement that modifications of mmaped page beyond inode size must not be written to the file. ext4_bio_write_page() did this only for blocks fully beyond inode size but didn't properly zero blocks partially beyond inode size. Fix this. The problem has been uncovered by mmap_11-4 test in openposix test suite (part of LTP). Reported-by:
Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com> Fixes: 5a0dc736 Fixes: bd2d0210Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.2: - Adjust context - block_end was used instead of block_start + blocksize] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Andreas Schrägle authored
commit 754a292f upstream. Add support for Marvell Technology Group Ltd. 88SE91A0 SATA 6Gb/s Controller by adding its PCI ID. Signed-off-by:
Andreas Schrägle <ajs124.ajs124@gmail.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Chris Wilson authored
commit 9aab8bff upstream. We only want to modifiy a single field in the userspace view of the execbuffer command buffer, so explicitly change that rather than copy everything back again. This serves two purposes: 1. The single fields are much cheaper to copy (constant size so the copy uses special case code) and much smaller than the whole array. 2. We modify the array for internal use that need to be masked from the user. Note: We need this backported since without it the next bugfix will blow up when userspace recycles batchbuffers and relocations. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> [bwh: Backported to 3.2: to_user_ptr() is open-coded] Signed-off-by:
-
Daniel Vetter authored
commit ff240199 upstream. These are all user-trigerable, so tune down their loudness a notch. For some of these we have i-g-t tests (because they prevent newly-discovered bugs), without this patches running the test suite leaves behind a dirty dmesg. Reviewed-by:
-
Krzysztof Hałasa authored
commit c7d37a66 upstream. Without this fix, freshly rebooted Linux creates a new IBSS instead of joining an existing one. Only when jiffies counter overflows after 5 minutes the IBSS can be successfully joined. Signed-off-by:
Krzysztof Hałasa <khalasa@piap.pl> [edit commit message slightly] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Hans de Goede authored
commit 6d396ede upstream. The T540p has a touchpad with pnp-id LEN0034, all the models with this pnp-id have the same min/max values, except the T540p where the values are slightly off. Fix them to be identical. This is a preparation patch for simplifying the quirk table. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Andrey Ryabinin authored
commit 537094b6 upstream. According to arm procedure call standart r2 register is call-cloberred. So after the result of x expression was put into r2 any following function call in p may overwrite r2. To fix this, the result of p expression must be saved to the temporary variable before the assigment x expression to __r2. Signed-off-by:
Andrey Ryabinin <a.ryabinin@samsung.com> Reviewed-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Alan Stern authored
commit 8ef42ddd upstream. Not all host controller drivers have bus-suspend and bus-resume methods. When one doesn't, it will cause problems if runtime PM is enabled in the kernel. The PM core will attempt to suspend the controller's root hub, the suspend will fail because there is no bus-suspend routine, and a -EBUSY error code will be returned to the PM core. This will cause the suspend attempt to be repeated shortly thereafter, in a never-ending loop. Part of the problem is that the original error code -ENOENT gets changed to -EBUSY in usb_runtime_suspend(), on the grounds that the PM core will interpret -ENOENT as meaning that the root hub has gotten into a runtime-PM error state. While this change is appropriate for real USB devices, it's not such a good idea for a root hub. In fact, considering the root hub to be in a runtime-PM error state would not be far from the truth. Therefore this patch updates usb_runtime_suspend() so that it adjusts error codes only for non-root-hub devices. Furthermore, the patch attempts to prevent the problem from occurring in the first place by not enabling runtime PM by default for root hubs whose host controller driver doesn't have bus_suspend and bus_resume methods. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Will Deacon <will.deacon@arm.com> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: runtime PM is also not supported for USB 3.0 non-root hubs] Signed-off-by:
-
Mikulas Patocka authored
commit 972754cf upstream. I had occasional screen corruption with the matrox framebuffer driver and I found out that the reason for the corruption is that the hardware blitter accesses the videoram while it is being written to. The matrox driver has a macro WaitTillIdle() that should wait until the blitter is idle, but it sometimes doesn't work. I added a dummy read mga_inl(M_STATUS) to WaitTillIdle() to fix the problem. The dummy read will flush the write buffer in the PCI chipset, and the next read of M_STATUS will return the hardware status. Since applying this patch, I had no screen corruption at all. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Emil Goode authored
commit d1d70e5d upstream. If we fail to allocate struct platform_device pdev we dereference it after the goto label err. This bug was found using coccinelle. Fixes: afa77ef3 (ARM: mx3: dynamically allocate "ipu-core" devices) Signed-off-by:
Emil Goode <emilgoode@gmail.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Shawn Guo <shawn.guo@freescale.com> Signed-off-by:
Olof Johansson <olof@lixom.net> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Jeff Mahoney authored
commit 22e7478d upstream. Prior to commit 0e4f6a79 (Fix reiserfs_file_release()), reiserfs truncates serialized on i_mutex. They mostly still do, with the exception of reiserfs_file_release. That blocks out other writers via the tailpack mutex and the inode openers counter adjusted in reiserfs_file_open. However, NFS will call reiserfs_setattr without having called ->open, so we end up with a race when nfs is calling ->setattr while another process is releasing the file. Ultimately, it triggers the BUG_ON(inode->i_size != new_file_size) check in maybe_indirect_to_direct. The solution is to pull the lock into reiserfs_setattr to encompass the truncate_setsize call as well. Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Signed-off-by:
-
Marco Stornelli authored
commit cfac4b47 upstream. Removed vmtruncate Signed-off-by:
Marco Stornelli <marco.stornelli@gmail.com> Reviewed-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Bart Van Assche authored
commit 024ca901 upstream. Avoid that the loops that iterate over the request ring can encounter a pointer to a SCSI command in req->scmnd that is no longer associated with that request. If the function srp_unmap_data() is invoked twice for a SCSI command that is not in flight then that would cause ib_fmr_pool_unmap() to be invoked with an invalid pointer as argument, resulting in a kernel oops. Reported-by:
Sagi Grimberg <sagig@mellanox.com> Reference: http://thread.gmane.org/gmane.linux.drivers.rdma/19068/focus=19069Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Kees Cook authored
commit 1b15d2e5 upstream. Some drivers use the first HID report in the list instead of using an index. In these cases, validation uses ID 0, which was supposed to mean "first known report". This fixes the problem, which was causing at least the lgff family of devices to stop working since hid_validate_values was being called with ID 0, but the devices used single numbered IDs for their reports: 0x05, 0x01, /* Usage Page (Desktop), */ 0x09, 0x05, /* Usage (Gamepad), */ 0xA1, 0x01, /* Collection (Application), */ 0xA1, 0x02, /* Collection (Logical), */ 0x85, 0x01, /* Report ID (1), */ ... Reported-by:
Simon Wood <simon@mungewell.org> Signed-off-by:
Kees Cook <keescook@chromium.org> Reviewed-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Lv Zheng authored
commit 73577d1d upstream. This patch fixes the following issue: If DSDT is customized, no local DSDT copy is needed. References: https://bugzilla.kernel.org/show_bug.cgi?id=69711Signed-off-by:
Enrico Etxe Arte <goitizena.generoa@gmail.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> [rjw: Subject] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Hans de Goede authored
commit 0b5fe736 upstream. https://bugzilla.redhat.com/show_bug.cgi?id=1096436 Tested-and-reported-by: ajayr@bigfoot.com Signed-off-by:
-
hujianyang authored
commit 691a7c6f upstream. There is a race condition in UBIFS: Thread A (mmap) Thread B (fsync) ->__do_fault ->write_cache_pages -> ubifs_vm_page_mkwrite -> budget_space -> lock_page -> release/convert_page_budget -> SetPagePrivate -> TestSetPageDirty -> unlock_page -> lock_page -> TestClearPageDirty -> ubifs_writepage -> do_writepage -> release_budget -> ClearPagePrivate -> unlock_page -> !(ret & VM_FAULT_LOCKED) -> lock_page -> set_page_dirty -> ubifs_set_page_dirty -> TestSetPageDirty (set page dirty without budgeting) -> unlock_page This leads to situation where we have a diry page but no budget allocated for this page, so further write-back may fail with -ENOSPC. In this fix we return from page_mkwrite without performing unlock_page. We return VM_FAULT_LOCKED instead. After doing this, the race above will not happen. Signed-off-by:
hujianyang <hujianyang@huawei.com> Tested-by:
Laurence Withers <lwithers@guralp.com> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Thomas Gleixner authored
commit 1e77d0a1 upstream. Till reported that the spurious interrupt detection of threaded interrupts is broken in two ways: - note_interrupt() is called for each action thread of a shared interrupt line. That's wrong as we are only interested whether none of the device drivers felt responsible for the interrupt, but by calling multiple times for a single interrupt line we account IRQ_NONE even if one of the drivers felt responsible. - note_interrupt() when called from the thread handler is not serialized. That leaves the members of irq_desc which are used for the spurious detection unprotected. To solve this we need to defer the spurious detection of a threaded interrupt to the next hardware interrupt context where we have implicit serialization. If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we check whether the previous interrupt requested a deferred check. If not, we request a deferred check for the next hardware interrupt and return. If set, we check whether one of the interrupt threads signaled success. Depending on this information we feed the result into the spurious detector. If one primary handler of a shared interrupt returns IRQ_HANDLED we disable the deferred check of irq threads on the same line, as we have found at least one device driver who cared. Reported-by:
Till Straumann <strauman@slac.stanford.edu> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Tested-by:
Austin Schuh <austin@peloton-tech.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: linux-can@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Felipe Balbi authored
commit da64c27d upstream. LDISCs shouldn't call tty->ops->write() from within ->write_wakeup(). ->write_wakeup() is called with port lock taken and IRQs disabled, tty->ops->write() will try to acquire the same port lock and we will deadlock. Acked-by:
Marcel Holtmann <marcel@holtmann.org> Reviewed-by:
Peter Hurley <peter@hurleysoftware.com> Reported-by:
Huang Shijie <b32955@freescale.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Tested-by:
Andreas Bießmann <andreas@biessmann.de> Signed-off-by:
-
Will Deacon authored
commit 498c2280 upstream. kmap_to_page returns the corresponding struct page for a virtual address of an arbitrary mapping. This works by checking whether the address falls in the pkmap region and using the pkmap page tables instead of the linear mapping if appropriate. Unfortunately, the bounds checking means that PKMAP_ADDR(LAST_PKMAP) is incorrectly treated as a highmem address and we can end up walking off the end of pkmap_page_table and subsequently passing junk to pte_page. This patch fixes the bound check to stay within the pkmap tables. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
- 09 Jun, 2014 20 commits
-
-
Ben Hutchings authored
-
Thomas Gleixner authored
commit 54a21788 upstream. The current implementation of lookup_pi_state has ambigous handling of the TID value 0 in the user space futex. We can get into the kernel even if the TID value is 0, because either there is a stale waiters bit or the owner died bit is set or we are called from the requeue_pi path or from user space just for fun. The current code avoids an explicit sanity check for pid = 0 in case that kernel internal state (waiters) are found for the user space address. This can lead to state leakage and worse under some circumstances. Handle the cases explicit: Waiter | pi_state | pi->owner | uTID | uODIED | ? [1] NULL | --- | --- | 0 | 0/1 | Valid [2] NULL | --- | --- | >0 | 0/1 | Valid [3] Found | NULL | -- | Any | 0/1 | Invalid [4] Found | Found | NULL | 0 | 1 | Valid [5] Found | Found | NULL | >0 | 1 | Invalid [6] Found | Found | task | 0 | 1 | Valid [7] Found | Found | NULL | Any | 0 | Invalid [8] Found | Found | task | ==taskTID | 0/1 | Valid [9] Found | Found | task | 0 | 0 | Invalid [10] Found | Found | task | !=taskTID | 0/1 | Invalid [1] Indicates that the kernel can acquire the futex atomically. We came came here due to a stale FUTEX_WAITERS/FUTEX_OWNER_DIED bit. [2] Valid, if TID does not belong to a kernel thread. If no matching thread is found then it indicates that the owner TID has died. [3] Invalid. The waiter is queued on a non PI futex [4] Valid state after exit_robust_list(), which sets the user space value to FUTEX_WAITERS | FUTEX_OWNER_DIED. [5] The user space value got manipulated between exit_robust_list() and exit_pi_state_list() [6] Valid state after exit_pi_state_list() which sets the new owner in the pi_state but cannot access the user space value. [7] pi_state->owner can only be NULL when the OWNER_DIED bit is set. [8] Owner and user space value match [9] There is no transient state which sets the user space TID to 0 except exit_robust_list(), but this is indicated by the FUTEX_OWNER_DIED bit. See [4] [10] There is no transient state which leaves owner and user space TID out of sync. Signed-off-by:
-
Thomas Gleixner authored
commit 13fbca4c upstream. If the owner died bit is set at futex_unlock_pi, we currently do not cleanup the user space futex. So the owner TID of the current owner (the unlocker) persists. That's observable inconsistant state, especially when the ownership of the pi state got transferred. Clean it up unconditionally. Signed-off-by:
-
Thomas Gleixner authored
commit b3eaa9fc upstream. We need to protect the atomic acquisition in the kernel against rogue user space which sets the user space futex to 0, so the kernel side acquisition succeeds while there is existing state in the kernel associated to the real owner. Verify whether the futex has waiters associated with kernel state. If it has, return -EINVAL. The state is corrupted already, so no point in cleaning it up. Subsequent calls will fail as well. Not our problem. [ tglx: Use futex_top_waiter() and explain why we do not need to try restoring the already corrupted user space state. ] Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Cc: Kees Cook <keescook@chromium.org> Cc: Will Drewry <wad@chromium.org> Signed-off-by:
-
Thomas Gleixner authored
futex-prevent-requeue-pi-on-same-futex.patch futex: Forbid uaddr == uaddr2 in futex_requeue(..., requeue_pi=1) commit e9c243a5 upstream. If uaddr == uaddr2, then we have broken the rule of only requeueing from a non-pi futex to a pi futex with this call. If we attempt this, then dangling pointers may be left for rt_waiter resulting in an exploitable condition. This change brings futex_requeue() in line with futex_wait_requeue_pi() which performs the same check as per commit 6f7b0a2a ("futex: Forbid uaddr == uaddr2 in futex_wait_requeue_pi()") [ tglx: Compare the resulting keys as well, as uaddrs might be different depending on the mapping ] Fixes CVE-2014-3153. Reported-by: Pinkie Pie Signed-off-by:
Will Drewry <wad@chromium.org> Signed-off-by:
-
Thomas Gleixner authored
commit f0d71b3d upstream. We happily allow userspace to declare a random kernel thread to be the owner of a user space PI futex. Found while analysing the fallout of Dave Jones syscall fuzzer. We also should validate the thread group for private futexes and find some fast way to validate whether the "alleged" owner has RW access on the file which backs the SHM, but that's a separate issue. Signed-off-by:
-
Thomas Gleixner authored
commit 866293ee upstream. Dave Jones trinity syscall fuzzer exposed an issue in the deadlock detection code of rtmutex: http://lkml.kernel.org/r/20140429151655.GA14277@redhat.com That underlying issue has been fixed with a patch to the rtmutex code, but the futex code must not call into rtmutex in that case because - it can detect that issue early - it avoids a different and more complex fixup for backing out If the user space variable got manipulated to 0x80000000 which means no lock holder, but the waiters bit set and an active pi_state in the kernel is found we can figure out the recursive locking issue by looking at the pi_state owner. If that is the current task, then we can safely return -EDEADLK. The check should have been added in commit 59fa6245 (futex: Handle futex_pi OWNER_DIED take over correctly) already, but I did not see the above issue caused by user space manipulation back then. Signed-off-by:
-
Naoya Horiguchi authored
commit 3e030ecc upstream. When a memory error happens on an in-use page or (free and in-use) hugepage, the victim page is isolated with its refcount set to one. When you try to unpoison it later, unpoison_memory() calls put_page() for it twice in order to bring the page back to free page pool (buddy or free hugepage list). However, if another memory error occurs on the page which we are unpoisoning, memory_failure() returns without releasing the refcount which was incremented in the same call at first, which results in memory leak and unconsistent num_poisoned_pages statistics. This patch fixes it. Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by:
-
Chen Yucong authored
commit b985194c upstream. For handling a free hugepage in memory failure, the race will happen if another thread hwpoisoned this hugepage concurrently. So we need to check PageHWPoison instead of !PageHWPoison. If hwpoison_filter(p) returns true or a race happens, then we need to unlock_page(hpage). Signed-off-by:
Chen Yucong <slaoub@gmail.com> Reviewed-by:
Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Ezequiel Garcia authored
commit 5a9a55bf upstream. We need to use writel() instead of writel_relaxed() when starting a channel, to ensure all the descriptors have been flushed before the activation. While at it, remove the unneeded read-modify-write and make the code simpler. Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> [bwh: Backported to 3.2: it was using __raw_readl() and __raw_writel() which are just as wrong] Signed-off-by:
-
J. Bruce Fields authored
commit 27b11428 upstream. The current code assumes a one-to-one lockowner<->lock stateid correspondance. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
J. Bruce Fields authored
commit a1b8ff4c upstream. The nfsv4 state code has always assumed a one-to-one correspondance between lock stateid's and lockowners even if it appears not to in some places. We may actually change that, but for now when FREE_STATEID releases a lock stateid it also needs to release the parent lockowner. Symptoms were a subsequent LOCK crashing in find_lockowner_str when it calls same_lockowner_ino on a lockowner that unexpectedly has an empty so_stateids list. Signed-off-by:
-
Stephane Grosjean authored
commit 0b5a958c upstream. As remarked by Christopher R. Baker in his post at http://marc.info/?l=linux-can&m=139707295706465&w=2 there's a possibility for an use after free condition at device removal. This simplified patch introduces an additional variable to prevent the issue. Thanks for catching this. Reported-by:
Christopher R. Baker <cbaker@rec.ri.cmu.edu> Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Stephane Grosjean authored
commit 29830406 upstream. Change the way channels objects are linked together by peak_pci_probe() avoiding any kernel oops when driver is removed. Side effect is that the list is now browsed from last to first channel. Signed-off-by:
-
Alex Deucher authored
commit d8ade352 upstream. Newer PX systems have non-VGA pci class dGPUs. Update the ATRM fetch method to handle those cases. bug: https://bugzilla.kernel.org/show_bug.cgi?id=75401Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Christian König <christian.koenig@amd.com> [bwh: Backported to 3.2: s/ACPI_HANDLE()/DEVICE_ACPI_HANDLE()/] Signed-off-by:
-
Christian König authored
commit 54409259 upstream. Placing them exclusively into VRAM might not work all the time. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=78297Signed-off-by:
-
Jiri Olsa authored
commit 39af6b16 upstream. The perf cpu offline callback takes down all cpu context events and releases swhash->swevent_hlist. This could race with task context software event being just scheduled on this cpu via perf_swevent_add while cpu hotplug code already cleaned up event's data. The race happens in the gap between the cpu notifier code and the cpu being actually taken down. Note that only cpu ctx events are terminated in the perf cpu hotplug code. It's easily reproduced with: $ perf record -e faults perf bench sched pipe while putting one of the cpus offline: # echo 0 > /sys/devices/system/cpu/cpu1/online Console emits following warning: WARNING: CPU: 1 PID: 2845 at kernel/events/core.c:5672 perf_swevent_add+0x18d/0x1a0() Modules linked in: CPU: 1 PID: 2845 Comm: sched-pipe Tainted: G W 3.14.0+ #256 Hardware name: Intel Corporation Montevina platform/To be filled by O.E.M., BIOS AMVACRB1.86C.0066.B00.0805070703 05/07/2008 0000000000000009 ffff880077233ab8 ffffffff81665a23 0000000000200005 0000000000000000 ffff880077233af8 ffffffff8104732c 0000000000000046 ffff88007467c800 0000000000000002 ffff88007a9cf2a0 0000000000000001 Call Trace: [<ffffffff81665a23>] dump_stack+0x4f/0x7c [<ffffffff8104732c>] warn_slowpath_common+0x8c/0xc0 [<ffffffff8104737a>] warn_slowpath_null+0x1a/0x20 [<ffffffff8110fb3d>] perf_swevent_add+0x18d/0x1a0 [<ffffffff811162ae>] event_sched_in.isra.75+0x9e/0x1f0 [<ffffffff8111646a>] group_sched_in+0x6a/0x1f0 [<ffffffff81083dd5>] ? sched_clock_local+0x25/0xa0 [<ffffffff811167e6>] ctx_sched_in+0x1f6/0x450 [<ffffffff8111757b>] perf_event_sched_in+0x6b/0xa0 [<ffffffff81117a4b>] perf_event_context_sched_in+0x7b/0xc0 [<ffffffff81117ece>] __perf_event_task_sched_in+0x43e/0x460 [<ffffffff81096f1e>] ? put_lock_stats.isra.18+0xe/0x30 [<ffffffff8107b3c8>] finish_task_switch+0xb8/0x100 [<ffffffff8166a7de>] __schedule+0x30e/0xad0 [<ffffffff81172dd2>] ? pipe_read+0x3e2/0x560 [<ffffffff8166b45e>] ? preempt_schedule_irq+0x3e/0x70 [<ffffffff8166b45e>] ? preempt_schedule_irq+0x3e/0x70 [<ffffffff8166b464>] preempt_schedule_irq+0x44/0x70 [<ffffffff816707f0>] retint_kernel+0x20/0x30 [<ffffffff8109e60a>] ? lockdep_sys_exit+0x1a/0x90 [<ffffffff812a4234>] lockdep_sys_exit_thunk+0x35/0x67 [<ffffffff81679321>] ? sysret_check+0x5/0x56 Fixing this by tracking the cpu hotplug state and displaying the WARN only if current cpu is initialized properly. Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Jiri Olsa <jolsa@redhat.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1396861448-10097-1-git-send-email-jolsa@redhat.comSigned-off-by:
-
Peter Zijlstra authored
commit 0819b2e3 upstream. Vince reported that using a large sample_period (one with bit 63 set) results in wreckage since while the sample_period is fundamentally unsigned (negative periods don't make sense) the way we implement things very much rely on signed logic. So limit sample_period to 63 bits to avoid tripping over this. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Signed-off-by:
-
Chunwei Chen authored
commit 178eda29 upstream. It has been reported that using ZFSonLinux on rbd will result in memory corruption. The bug report can be found here: https://github.com/zfsonlinux/spl/issues/241 http://tracker.ceph.com/issues/7790 The reason is that ZFS will send pages with page_count 0 into rbd, which in turns send them to tcp_sendpage. However, tcp_sendpage cannot deal with page_count 0, as it will do get_page and put_page, and erroneously free the page. This type of issue has been noted before, and handled in iscsi, drbd, etc. So, rbd should also handle this. This fix address this issue by fall back to slower sendmsg when page_count 0 detected. Cc: Sage Weil <sage@inktank.com> Cc: Yehuda Sadeh <yehuda@inktank.com> Signed-off-by:
Chunwei Chen <tuxoko@gmail.com> Reviewed-by:
Ilya Dryomov <ilya.dryomov@inktank.com> Signed-off-by:
-
Alex Elder authored
commit e36b13cc upstream. Make ceph_tcp_sendpage() be the only place kernel_sendpage() is used, by using this helper in write_partial_msg_pages(). Signed-off-by:
Alex Elder <elder@dreamhost.com> Reviewed-by:
Sage Weil <sage@newdream.net> [bwh: Backported to 3.2: - Add ceph_tcp_sendpage(), from commit 31739139 ('libceph: use kernel_sendpage() for sending zeroes'), the rest of which is not applicable - Adjust context] Signed-off-by:
-
