The davinci McBSP (davinci-i2s) driver does not implement the set_sysclk
callback, which is fine and should not be treated as error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-5-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

Most of the daVinci devices does not boot with DT. In this case the DMA
channel is looked up with dma_slave_map and for that the chan_names[]
must be configured.

Both McASP and ASP/McBSP uses "tx" and "rx" as channel names, so we can
just do this when the dev->of_node is not valid.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-4-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

ASP/McBSP can support 8/16/20/24/32 bits word in theory. I have only tested
S16_LE and S32_LE, the other formats might not work so only extend the
supported formats with S32_LE for now.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190830103841.25128-2-peter.ujfalusi@ti.comSigned-off-by: Mark Brown <broonie@kernel.org>

On this codec SLIMBus RX path supports 384000 rate on primary interpolator.
Add this missing rate as supported rate.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190822095653.7200-3-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Most of the modern codecs supports 352.8KHz and 384KHz sample rates.
Currenlty HW params fails to set 352.8Kz and 384KHz sample rate
as these are not in known rates list.
Add these new rates to known list to allow them.

This patch also adds defines in pcm.h so that drivers can use it.
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20190822095653.7200-2-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This patch correct tdm out bck inverse register to AUDIO_TOP_CON3[3].
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1566621445-26989-4-git-send-email-jiaxin.yu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch refined tdm driver code, and allow tdm hw to support two
configurations in machine driver to output tdm signal or i2s signal.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1566621445-26989-3-git-send-email-jiaxin.yu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Enable support for left-justified data mode for SSC-codec link.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/44fa6b700421e80778f20ff9ead2b148cf6d2e92.1566677788.git.mirq-linux@rere.qmqm.plSigned-off-by: Mark Brown <broonie@kernel.org>

Rework DAI format calculation in preparation for adding more formats
later. As a side-effect this enables all CBM/CBS x CFM/CFS combinations
for supported formats. (Note: the additional modes are not tested.)

Note: this changes FSEDGE to POSITIVE for I2S CBM_CFS mode as the TXSYN
interrupt is not used anyway.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/f5949b0326fdcdca072f3ed03f77de9e207631cd.1566677788.git.mirq-linux@rere.qmqm.plSigned-off-by: Mark Brown <broonie@kernel.org>

Allow SSC to be used on platforms described using audio-graph-card
in Device Tree.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/233d5461f4448df151755de7b69a0cd3ad310d5c.1566677788.git.mirq-linux@rere.qmqm.plSigned-off-by: Mark Brown <broonie@kernel.org>

Use force_suspend/resume to make sure clocks are disabled/enabled
accordingly during system suspend/resume.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1566944026-18113-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Currently topology is kept in memory while driver is running. It's
unnecessary, as it's only needed during parsing.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-6-amadeuszx.slawinski@linux.intel.comReviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When we are printing module params, we were actually printing module id
instead of type, but debug message was saying that number we get is type.
So print module type, as it is useful when debugging paths, but also
keep printing module id, as it is used in all other logs.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@intel.com>
Link: https://lore.kernel.org/r/20190827141712.21015-5-amadeuszx.slawinski@linux.intel.comReviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The device_link_add() function only returns NULL on error, it doesn't
return error pointers.

Fixes: 202acc56 ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190826131855.GA6840@mwandaSigned-off-by: Mark Brown <broonie@kernel.org>

The last set of reworks included some fixes to change the A83t behaviour
and "fix" it.

It turns out that the controller described in the datasheet and the one
supported here are not the same, yet the A83t has the two of them, and the
one supported in the driver wasn't the one described in the datasheet.

Fix this by reintroducing the proper quirks.

Fixes: 69e450e5 ("ASoC: sun4i-i2s: Fix the LRCK period on A83t")
Fixes: bf943d52 ("ASoC: sun4i-i2s: Fix MCLK Enable bit offset on A83t")
Fixes: 2e04fc4d ("ASoC: sun4i-i2s: Fix WSS and SR fields for the A83t")
Fixes: 515fcfbc ("ASoC: sun4i-i2s: Fix LRCK and BCLK polarity offsets on newer SoCs")
Fixes: c1d3a921 ("ASoC: sun4i-i2s: Fix the MCLK and BCLK dividers on newer SoCs")
Fixes: fb19739d ("ASoC: sun4i-i2s: Use module clock as BCLK parent on newer SoCs")
Fixes: 71137bcd ("ASoC: sun4i-i2s: Move the format configuration to a callback")
Fixes: d70be625 ("ASoC: sun4i-i2s: Move the channel configuration to a callback")
Reported-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827123131.29129-2-mripard@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

In case of error, the function devm_ioremap_wc() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: 202acc56 ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190826120003.183279-1-weiyongjun1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove unused variable mt8183_mt6358_ts3a227_max98357_dapm_widgets and
mt8183_mt6358_ts3a227_max98357_dapm_routes.  They are accidentially
included when rebasing commits.

Fixes: 6191cbde ("ASoC: mediatek: mt8183: switch tdm pins gpio function when playback on or off")
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20190826032642.27324-1-tzungbi@google.comSigned-off-by: Mark Brown <broonie@kernel.org>

This reverts commit 3e9acd7a (ASoC: sun4i-i2s: Remove
duplicated quirks structure").

It turns out that while one I2S controller is described in the A83t
datasheet, the driver supports another, undocumented, one that has been
inherited from the older SoCs, while the documented one uses the new
design.

Fixes: 3e9acd7a ("ASoC: sun4i-i2s: Remove duplicated quirks structure")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/20190827093206.17919-1-mripard@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This platform device is registered from "fsl_audmix", which is
its parent device. If use pdev->dev.parent for the priv->card.dev,
the value set by dev_set_drvdata in parent device will be covered
by the value in child device.

Fixes: b86ef536 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1566921315-23402-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Fix sparse warnings:

sound/soc/sof/imx/imx8.c:104:6: warning: symbol 'imx8_dsp_handle_reply' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:115:6: warning: symbol 'imx8_dsp_handle_request' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:336:5: warning: symbol 'imx8_get_bar_index' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:341:6: warning: symbol 'imx8_ipc_msg_data' was not declared. Should it be static?
sound/soc/sof/imx/imx8.c:348:5: warning: symbol 'imx8_ipc_pcm_params' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190823125939.30012-1-yuehaibing@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.

From function name point of view, "soc_post_component_init()" sounds
like "component initialize function".
But in reality it is rtd setup function.

This patch renames soc_post_component_init() to soc_rtd_init()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9uo7lc3.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Initialize component related list at random place is very difficult
to read. This patch initialize it at snd_soc_component_initialize().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87y2zozazp.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

sof_get_control_data returns negative values even though the return
value is defined unsigned (size_t). So change the return value type to
int and add the data size as pointer argument to sof_get_control_data to
avoid ambiquity in the meaning of the return type.

Fixes: cac974a5 ("ASoC: SOF: topology: use set_get_data in process load")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaska Uimonen <jaska.uimonen@intel.com>
Link: https://lore.kernel.org/r/20190821211138.14618-1-jaska.uimonen@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

It might return without initializing in error case.
In such case, uninitialized variable might be used at error handler.
This patch initializes all necessary variable before return.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87zhk4zazt.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

commit 52abe6cc ("ASoC: topology: fix oops/use-after-free case
with dai driver") fixups remove_dai() error, but it is using
list_for_each_entry() for component->dai_list.

We already have for_each_component_dais() macro for it.
Let's use exising method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tvaczazd.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

.bus_control can be bit field.
this patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/87v9uszazh.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

There is no need to check return value for
soc_cleanup_card_resources(). Let't makes it as void.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/871rxg1lda.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

We can find specified name component via snd_soc_rtdcom_lookup().
But, it is not enough under multi CPU/Codec/Platform, because many
components which have same driver name might be connected to same rtd.

Not using this function as much as possible is best solution,
but some drivers are already deeply depended to it.

We can expand this function, for example having "num" which specifies
found order at parameter, etc (In such case, it need to have fixed
probing order).
Or, use different driver name in such component, etc.

We will have such issue if multi CPU/Codec/Platform were supported.
To indicate it, this patch adds NOTE to this function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/874l2c1ldi.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.

soc-core.c is using device_unregiser(), but there is no its paired
device_regiser(). We can find its code at soc_post_component_init()
which is using device_initialize() and device_add().
Here, device_initialize() + device_add() = device_register().

	-- linux/drivers/base/core.c --
	int device_register(struct device *dev)
	{
		device_initialize(dev);
		return device_add(dev);
	}

device_initialize() is doing each dev member's initialization only,
not related to device parent/release/groups.
Thus, we can postpone it.
let's use device_register() instead of device_initialize()/device_add().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/878sro1ldw.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull TDM pins down when TDM BE shutdown to avoid current leakage.
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1566478261-13464-2-git-send-email-jiaxin.yu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

sound/soc/mediatek/mt2701/mt2701-afe-common.h:66:27: warning:
 mt2701_afe_backup_list defined but not used [-Wunused-const-variable=]

mt2701_afe_backup_list is only used in mt2701-afe-pcm.c,
so just move the definition over there.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190822143747.20944-1-yuehaibing@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

sound/soc/codecs/wm8988.c:270:30: warning:
 wm8988_rline_enum defined but not used [-Wunused-const-variable=]

wm8988_rline_enum should be used in wm8988_right_line_controls.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 5409fb4e ("ASoC: Add WM8988 CODEC driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190822143608.59824-1-yuehaibing@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for the audio DSP hardware found on NXP i.MX8 platform.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821164730.7385-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for device tree based SOF DSP devices.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821164730.7385-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

This describes the DSP device tree node.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190821164730.7385-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

In addition to the I2S format, the controller also supports the DSP_*
formats.

This requires some extra care on the LRCK period calculation, since the
controller, with the PCM formats, require that the value set is no longer
the periods of LRCK for a single channel, but for all of them.

Let's add the code to deal with this, and support the DSP_A and DSP_B
formats.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/5562db1ac8759f12b1b87c3258223eed629ef771.1566392800.git-series.maxime.ripard@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The sun4i_i2s_hw_params function already has a variable holding the value
returned by params_width, so let's just use that variable instead of
calling params_width multiple times.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/f85a1c1e014080a4bbc3abd19bc8fdcb86f0981a.1566392800.git-series.maxime.ripard@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The LRCK period field in the FMT0 register holds the number of LRCK period
for one channel in I2S mode.

This has been hardcoded to 32, while it really should be the physical width
of the format, which creates an improper clock when using a 16bit format,
with the i2s controller as LRCK master.

Fixes: 7d299381 ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/f08a0c3605cd1d79752b38d704690190183f7865.1566392800.git-series.maxime.ripard@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The clock dividers function has been using the word size to compute the
clock rate at which it's supposed to be running, but the proper formula
would be to use the physical width and / or slot width in TDM.

It doesn't make any difference at the moment since all the formats
supported have the same sample width and physical width, but it's not going
to last forever.

Fixes: 7d299381 ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/41a359d9885f397e066816961e5e3236afcbe0a1.1566392800.git-series.maxime.ripard@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

The i2s controller supports TDM, for up to 8 slots. Let's support the TDM
API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/26392af30b3e7b31ee48d5b867d45be8675db046.1566242458.git-series.maxime.ripard@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>