Add myself as maintainer of the Loongson LS2X I2C driver.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

'DYNAMIC_MODE_READ_BROKEN_BIT' quirk added in the driver,
effected IP versions no longer enter dynamic mode.
So, remove local_irq_save/local_irq_restore APIs from driver.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

smbus_block_read is added to xiic driver to read from few sensors
which support this command. Since the number of bytes to read is not
known prior to transfer, xiic standard mode is being used for low level
control of IP.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

If the tx_half_empty interrupt comes first instead of tx_empty,
STOP bit is generated even before all the bytes are transmitted
out on the bus.
STOP bit should be sent only after all the bytes in the FIFO are
transmitted out of the FIFO. So wait until FIFO is empty before sending
the STOP bit.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Xilinx I2C IP has two modes of operation, both of which implement
I2C transactions. The only difference from sw perspective is the
programming sequence for these modes.
Dynamic mode  -> Simple to program, less number of steps in sequence.
Standard mode -> Gives flexibility, more number of steps in sequence.

In dynamic mode, during the i2c-read transactions, if there is a
delay(> 200us) between the register writes (address & byte count),
read transaction fails. On a system with load, this scenario is
occurring frequently.
To avoid this, switch to standard mode if there is a read request.

Added a quirk to identify the IP version effected by this and follow
the standard mode.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

repeated start

When a combined message request comes from user space, the
controller has to initiate repeated start sequence. In standard
mode, this repeated start sequence is corrupted if there is still
data in the Tx FIFO.

So, always make sure that all the bytes are completely transmitted
out of the FIFO by waiting for TXEMPTY, if the previous message is
of Tx type.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

read transfers

Added standard mode for AXI I2C controller to enable read transfers
of size more than 255 bytes. The driver selects standard mode in the
following scenarios.

1. If a single message request comes from user space, requesting a
read of more than 255 bytes

2. If a message set request comes from user space consisting of many
messages and if any one of them is a read operation, irrespective
of the size of transfer. (This is done because it is observed that
repeated start operation is not happening in dynamic mode read as
expected in a message set request from user space.)
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This I2C module is integrated into the Loongson-2K SoCs and Loongson
LS7A bridge chip.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add Loongson LS2X I2C controller binding with DT schema format using
json-schema.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

regmap_read() API signature expects the caller to send "unsigned int"
type to return back the read value, but there are some occurrences of 'u32'
across i2c-designware-* files.

Change them to match the regmap_read() signature.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

On some AMD platforms, based on the new designware datasheet,
BIOS sets the BIT(11) within the IC_CON register to advertise
the "bus clear feature capability".

AMD/Designware datasheet says:

Bit(11) BUS_CLEAR_FEATURE_CTRL. Read-write,Volatile. Reset: 0.
Description: In Master mode:
- 1'b1: Bus Clear Feature is enabled.
- 1'b0: Bus Clear Feature is Disabled.
In Slave mode, this register bit is not applicable.

On AMD platform designs:
1. BIOS programs the BUS_CLEAR_FEATURE_CTRL and enables the detection
of SCL/SDA stuck low.
2. Whenever the stuck low is detected, the SMU FW shall do the bus
recovery procedure.

Currently, the way in which the "master_cfg" is built in the driver, it
overrides the BUS_CLEAR_FEATURE_CTRL advertised by BIOS and the SMU FW
cannot initiate the bus recovery if the stuck low is detected.

Hence add a check in i2c_dw_probe_master() that if the BIOS
advertises the bus clear feature, let driver not ignore it and
adapt accordingly.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

There are slave devices that understand I2C but have read-only SDA and
SCL. Examples are FD650 7-segment LED controller and its derivatives.
Typical board designs don't even have a pull-up for both pins.
Handle the new attributes for write-only SDA and missing pull-up on
SDA/SCL.

For either pin the open-drain and has-no-pullup properties are
mutually-exclusive, what is documented in the DT property documentation.
We don't add an extra warning here because the open-drain properties
are marked deprecated anyway.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
[wsa: switched to device properties]
Signed-off-by: Wolfram Sang <wsa@kernel.org>

This is in preparation of supporting write-only SDA in i2c-gpio.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

There are slave devices that understand I2C but have read-only SDA and
SCL. Examples are FD650 7-segment LED controller and its derivatives.
Typical board designs don't even have a pull-up for both pins.
Therefore add properties for not using open-drain. For write-only SCL
we have a property already, add one for write-only SDA.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Document the compatible for the CCI block found on SM6350 SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add support for the ACPI-based device registration, so that the driver
can be also enabled through ACPI table.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Tested-by: Peibao Liu <liupeibao@loongson.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

In the mrecv() function the Cadence I2C driver has the following expression
in an if clause.

	((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
	 (id->recv_count <= CDNS_I2C_FIFO_DEPTH))

Earlier in the same function when I2C_M_RECV_LEN is set the recv_count is
initialized to a value that is larger than CDNS_I2C_FIFO_DEPTH. This means
if the first expression is false the second expression is also false.
Checking the first expression is thus redundant and can be removed.

This slightly simplifies the logic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The irq field of the driver state struct is only used in the probe
function. There is no need to keep it around. Remove it from the state
struct and use a on-stack variable instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

The CDNS_I2C_DATA_INTR_DEPTH is not used in the Cadence I2C driver. Remove
it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Currently the i2c subsystem rely on the controller device tree to
initialize the pinctrl recovery information, part of the drivers does
not set this field (rinfo->pinctrl), for example i2c DesignWare driver.

The pins information is saved part of the device structure before probe
and it's done on pinctrl_bind_pins().

Make the i2c init recovery to get the device pins if it's not
initialized by the driver from the device pins.
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add an API to get the pinctrl pins if it was initialized before driver
probed. This API will be used in I2C core to get the device pinctrl
information for recovery state change.
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add binding documentation for the MT8365 I2C controllers.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

We have a set of return values that notifier callbacks can return. They
should not return 0, error codes or anything other than those predefined
values. Make the i2c character device's callback return NOTIFY_DONE or
NOTIFY_OK depending on the situation.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Add fwnode APIs for finding and getting I2C adapters, which will be
used by the SFP code. These are passed the fwnode corresponding to
the adapter, and return the I2C adapter. It is the responsibility of
the caller to find the appropriate fwnode.

We keep the DT and ACPI interfaces, but where appropriate, recode them
to use the fwnode interfaces internally.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c_master_hub is only used in i2c-qcom-geni.c now,
change it to static.

Fixes: cacd9643 ("i2c: qcom-geni: add support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Make i2c_dw_clk_rate() to return u32 instead of unsigned long, as the
function return the value of get_clk_rate_khz() which returns u32.

Fixes: b33af11d ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Many compatibles have been introduced, pointing to the same config data.
Leave a note reminding future developers to not do that again.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Almost every compatible string in the CCI driver is a duplicate. Adjust
the bindings to include a common (first-soc-implementing-vX) compatible
to remove the need to keep adding superfluous compatible strings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

Pull powerpc fixes from Michael Ellerman:

 - Three fixes for various bogosity in our linker script, revealed
   by the recent commit which changed discard behaviour with some
   toolchains.

* tag 'powerpc-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/vmlinux.lds: Don't discard .comment
  powerpc/vmlinux.lds: Don't discard .rela* for relocatable builds
  powerpc/vmlinux.lds: Define RUNTIME_DISCARD_EXIT

Pull memblock fixes from Mike Rapoport:
 "Small fixes in kernel-doc and tests:

   - Fix kernel-doc for memblock_phys_free() to use correct names for
     the counterpart allocation methods

   - Fix compilation error in memblock tests"

* tag 'fixes-2023-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
  memblock: Fix doc for memblock_phys_free
  memblock tests: Fix compilation error.

Pull NFS client fixes from Trond Myklebust:

 - Fix a race in the RPCSEC_GSS upcall code that causes hung RPC calls

 - Fix a broken coalescing test in the pNFS file layout driver

 - Ensure that the access cache rcu path also applies the login test

 - Fix up for a sparse warning

* tag 'nfs-for-6.2-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: Fix up a sparse warning
  NFS: Judge the file access cache's timestamp in rcu path
  pNFS/filelayout: Fix coalescing test for single DS
  SUNRPC: ensure the matching upcall is in-flight upon downcall

Pull cifs fixes from Steve French:
 "cifs/smb3 client fixes:

   - two multichannel fixes

   - three reconnect fixes

   - unmap fix"

* tag '6.2-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix interface count calculation during refresh
  cifs: refcount only the selected iface during interface update
  cifs: protect access of TCP_Server_Info::{dstaddr,hostname}
  cifs: fix race in assemble_neg_contexts()
  cifs: ignore ipc reconnect failures during dfs failover
  cifs: Fix kmap_local_page() unmapping

Pull devicetree fixes from Rob Herring:

 - Fix DT memory scanning for some MIPS boards when memory is not
   specified in DT

 - Redo CONFIG_CMDLINE* handling for missing /chosen node. The first
   attempt broke PS3 (and possibly other PPC platforms).

 - Fix constraints in QCom Soundwire schema

* tag 'devicetree-fixes-for-6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: fdt: Honor CONFIG_CMDLINE* even without /chosen node, take 2
  Revert "of: fdt: Honor CONFIG_CMDLINE* even without /chosen node"
  dt-bindings: soundwire: qcom,soundwire: correct sizes related to number of ports
  of/fdt: run soc memory setup when early_init_dt_scan_memory fails

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes for 6.2-rc3 that resolve some
  reported issues. They include:

   - of-reported ulpi problem, so the offending commit is reverted

   - dwc3 driver bugfixes for recent changes

   - fotg210 fixes

  Most of these have been in linux-next for a while, the last few were
  on the mailing list for a long time and passed all the 0-day bot
  testing so all should be fine with them as well"

* tag 'usb-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: dwc3: gadget: Ignore End Transfer delay on teardown
  usb: dwc3: xilinx: include linux/gpio/consumer.h
  usb: fotg210-udc: fix error return code in fotg210_udc_probe()
  usb: fotg210: fix OTG-only build
  Revert "usb: ulpi: defer ulpi_register on ulpi_read_id timeout"