The DCache clean & ICache invalidation requirements for instructions
to be data coherence are discoverable through new fields in CTR_EL0.
The following two control bits DIC and IDC were defined for this
purpose. No need to perform point of unification cache maintenance
operations from software on systems where CPU caches are transparent.

This patch optimize the three functions __flush_cache_user_range(),
clean_dcache_area_pou() and invalidate_icache_range() if the hardware
reports CTR_EL0.IDC and/or CTR_EL0.IDC. Basically it skips the two
instructions 'DC CVAU' and 'IC IVAU', and the associated loop logic
in order to avoid the unnecessary overhead.

CTR_EL0.DIC: Instruction cache invalidation requirements for
 instruction to data coherence. The meaning of this bit[29].
  0: Instruction cache invalidation to the point of unification
     is required for instruction to data coherence.
  1: Instruction cache cleaning to the point of unification is
      not required for instruction to data coherence.

CTR_EL0.IDC: Data cache clean requirements for instruction to data
 coherence. The meaning of this bit[28].
  0: Data cache clean to the point of unification is required for
     instruction to data coherence, unless CLIDR_EL1.LoC == 0b000
     or (CLIDR_EL1.LoUIS == 0b000 && CLIDR_EL1.LoUU == 0b000).
  1: Data cache clean to the point of unification is not required
     for instruction to data coherence.
Co-authored-by: Philip Elcan <pelcan@codeaurora.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Omit patching of ADRP instruction at module load time if the current
CPUs are not susceptible to the erratum.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: Drop duplicate initialisation of .def_scope field]
Signed-off-by: Will Deacon <will.deacon@arm.com>

In some cases, core variants that are affected by a certain erratum
also exist in versions that have the erratum fixed, and this fact is
recorded in a dedicated bit in system register REVIDR_EL1.

Since the architecture does not require that a certain bit retains
its meaning across different variants of the same model, each such
REVIDR bit is tightly coupled to a certain revision/variant value,
and so we need a list of revidr_mask/midr pairs to carry this
information.

So add the struct member and the associated macros and handling to
allow REVIDR fixes to be taken into account.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Working around Cortex-A53 erratum #843419 involves special handling of
ADRP instructions that end up in the last two instruction slots of a
4k page, or whose output register gets overwritten without having been
read. (Note that the latter instruction sequence is never emitted by
a properly functioning compiler, which is why it is disregarded by the
handling of the same erratum in the bfd.ld linker which we rely on for
the core kernel)

Normally, this gets taken care of by the linker, which can spot such
sequences at final link time, and insert a veneer if the ADRP ends up
at a vulnerable offset. However, linux kernel modules are partially
linked ELF objects, and so there is no 'final link time' other than the
runtime loading of the module, at which time all the static relocations
are resolved.

For this reason, we have implemented the #843419 workaround for modules
by avoiding ADRP instructions altogether, by using the large C model,
and by passing -mpc-relative-literal-loads to recent versions of GCC
that may emit adrp/ldr pairs to perform literal loads. However, this
workaround forces us to keep literal data mixed with the instructions
in the executable .text segment, and literal data may inadvertently
turn into an exploitable speculative gadget depending on the relative
offsets of arbitrary symbols.

So let's reimplement this workaround in a way that allows us to switch
back to the small C model, and to drop the -mpc-relative-literal-loads
GCC switch, by patching affected ADRP instructions at runtime:
- ADRP instructions that do not appear at 4k relative offset 0xff8 or
  0xffc are ignored
- ADRP instructions that are within 1 MB of their target symbol are
  converted into ADR instructions
- remaining ADRP instructions are redirected via a veneer that performs
  the load using an unaffected movn/movk sequence.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: tidied up ADRP -> ADR instruction patching.]
[will: use ULL suffix for 64-bit immediate]
Signed-off-by: Will Deacon <will.deacon@arm.com>

We currently have to rely on the GCC large code model for KASLR for
two distinct but related reasons:
- if we enable full randomization, modules will be loaded very far away
  from the core kernel, where they are out of range for ADRP instructions,
- even without full randomization, the fact that the 128 MB module region
  is now no longer fully reserved for kernel modules means that there is
  a very low likelihood that the normal bottom-up allocation of other
  vmalloc regions may collide, and use up the range for other things.

Large model code is suboptimal, given that each symbol reference involves
a literal load that goes through the D-cache, reducing cache utilization.
But more importantly, literals are not instructions but part of .text
nonetheless, and hence mapped with executable permissions.

So let's get rid of our dependency on the large model for KASLR, by:
- reducing the full randomization range to 4 GB, thereby ensuring that
  ADRP references between modules and the kernel are always in range,
- reduce the spillover range to 4 GB as well, so that we fallback to a
  region that is still guaranteed to be in range
- move the randomization window of the core kernel to the middle of the
  VMALLOC space

Note that KASAN always uses the module region outside of the vmalloc space,
so keep the kernel close to that if KASAN is enabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

When PLTs are emitted at relocation time, we really should not exceed
the number that we counted when parsing the relocation tables, and so
currently, we BUG() on this condition. However, even though this is a
clear bug in this particular piece of code, we can easily recover by
failing to load the module.

So instead, return 0 from module_emit_plt_entry() if this condition
occurs, which is not a valid kernel address, and can hence serve as
a flag value that makes the relocation routine bail out.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

TCR_EL1.NFD1 was allocated by SVE and ensures that fault-surpressing SVE
memory accesses (e.g. speculative accesses from a first-fault gather load)
which translate via TTBR1_EL1 result in a translation fault if they
miss in the TLB when executed from EL0. This mitigates some timing attacks
against KASLR, where the kernel address space could otherwise be probed
efficiently using the FFR in conjunction with suppressed faults on SVE
loads.

Cc: Dave Martin <Dave.Martin@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This is the equivalent of commit 001bf455 ("ARM: 8428/1: kgdb: Fix
registers on sleeping tasks") but for arm64.  Nuff said.

...well, perhaps I could also add that task_pt_regs are userspace
registers and that's not what kgdb is supposed to be reporting.  We're
supposed to be reporting kernel registers.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

On arm64, the EFI stub and the kernel proper are essentially the same
binary, although the EFI stub executes at a different virtual address
as the kernel. For this reason, the EFI stub is restricted in the
symbols it can link to, which is ensured by prefixing all EFI stub
symbols with __efistub_ (and emitting __efistub_ prefixed aliases for
routines that may be shared between the core kernel and the stub)

These symbols are leaking into kallsyms, polluting the namespace, so
let's filter them explicitly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

This is a follow up patch to the series I sent recently that cleans up
KASAN_SHADOW_SCALE_SHIFT usage (which value was hardcoded and scattered
all over the code). This fixes the one place that I forgot to fix.

The change is purely aesthetical, instead of hardcoding the value for
KASAN_SHADOW_SCALE_SHIFT in arch/arm64/Makefile, an appropriate variable
is declared and used.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Commit 97303480 ("arm64: Increase the max granular size") increased
the cache line size to 128 to match Cavium ThunderX, apparently for some
performance benefit which could not be confirmed. This change, however,
has an impact on the network packets allocation in certain
circumstances, requiring slightly over a 4K page with a significant
performance degradation.

This patch reverts L1_CACHE_SHIFT back to 6 (64-byte cache line) while
keeping ARCH_DMA_MINALIGN at 128. The cache_line_size() function was
changed to default to ARCH_DMA_MINALIGN in the absence of a meaningful
CTR_EL0.CWG bit field.

In addition, if a system with ARCH_DMA_MINALIGN < CTR_EL0.CWG is
detected, the kernel will force swiotlb bounce buffering for all
non-coherent devices since DMA cache maintenance on sub-CWG ranges is
not safe, leading to data corruption.

Cc: Tirumalesh Chalamarla <tchalamarla@cavium.com>
Cc: Timur Tabi <timur@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

In cases where x30 is used as a temporary in the out-of-line ll/sc atomics
(e.g. atomic_fetch_add), the compiler tends to put out a full stackframe,
which included pointing the x29 at the new frame.

Since these things aren't traceable anyway, we can pass -fomit-frame-pointer
to reduce the work when spilling. Since this is incompatible with -pg, we
also remove that from the CFLAGS for this file.
Signed-off-by: Will Deacon <will.deacon@arm.com>

Using arm64_force_sig_info means that printing messages about unhandled
signals is dealt with for us, so use that in preference to force_sig_info
and remove any homebrew printing code.
Signed-off-by: Will Deacon <will.deacon@arm.com>

show_unhandled_signals_ratelimited is only called in traps.c, so move it
out of its macro in the dreaded system_misc.h and into a static function
in traps.c
Signed-off-by: Will Deacon <will.deacon@arm.com>

If we fail to deliver a signal due to taking an unhandled fault on the
stackframe, we can call arm64_notify_segfault to deliver a SEGV can deal
with printing any unhandled signal messages for us, rather than roll our
own printing code.

A side-effect of this change is that we now deliver the frame address
in si_addr along with an si_code of SEGV_{ACC,MAP}ERR, rather than an
si_addr of 0 and an si_code of SI_KERNEL as before.
Signed-off-by: Will Deacon <will.deacon@arm.com>

Reporting unhandled user pagefaults via arm64_force_sig_info means
that __do_user_fault can be drastically simplified, since it no longer
has to worry about printing the fault information and can consequently
just take the siginfo as a parameter.
Signed-off-by: Will Deacon <will.deacon@arm.com>

There's no need for callers of arm64_notify_die to print information
about user faults. Instead, they can pass a string to arm64_notify_die
which will be printed subject to show_unhandled_signals.
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64_notify_die deals with printing out information regarding unhandled
signals, so there's no need to roll our own code here.
Signed-off-by: Will Deacon <will.deacon@arm.com>

In preparation for consolidating our handling of printing unhandled
signals, introduce a wrapper around force_sig_info which can act as
the canonical place for dealing with show_unhandled_signals.

Initially, we just hook this up to arm64_notify_die.
Signed-off-by: Will Deacon <will.deacon@arm.com>

For signals other than SIGKILL or those with siginfo_layout(signal, code)
== SIL_FAULT then force_signal_inject does not initialise the siginfo_t
properly. Since the signal number is determined solely by the caller,
simply WARN on unknown signals and force to SIGKILL.
Reported-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

force_signal_inject is a little flakey:

  * It only knows about SIGILL and SIGSEGV, so can potentially deliver
    other signals based on a partially initialised siginfo_t

  * It sets si_addr to point at the PC for SIGSEGV

  * It always operates on current, so doesn't need the regs argument

This patch fixes these issues by always assigning the si_addr field to
the address parameter of the function and updates the callers (including
those that indirectly call via arm64_notify_segfault) accordingly.
Signed-off-by: Will Deacon <will.deacon@arm.com>

The word "feature" is repeated in the CPU features reporting. This drops it
for improved readability.

Before (redundant "feature" word):

 SMP: Total of 4 processors activated.
 CPU features: detected feature: 32-bit EL0 Support
 CPU features: detected feature: Kernel page table isolation (KPTI)
 CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
 CPU: All CPU(s) started at EL2

After:

 SMP: Total of 4 processors activated.
 CPU features: detected: 32-bit EL0 Support
 CPU features: detected: Kernel page table isolation (KPTI)
 CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
 CPU: All CPU(s) started at EL2
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

The PAN emulation notification was only happening for non-boot CPUs
if CPU capabilities had already been configured. This seems to be the
wrong place, as it's system-wide and isn't attached to capabilities,
so its reporting didn't normally happen. Instead, report it once from
the boot CPU.

Before (missing PAN emulation report):

 SMP: Total of 4 processors activated.
 CPU features: detected feature: 32-bit EL0 Support
 CPU features: detected feature: Kernel page table isolation (KPTI)
 CPU: All CPU(s) started at EL2

After:

 SMP: Total of 4 processors activated.
 CPU features: detected feature: 32-bit EL0 Support
 CPU features: detected feature: Kernel page table isolation (KPTI)
 CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
 CPU: All CPU(s) started at EL2
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Now that the early kernel mapping logic can tolerate placements of
Image that cross swapper table boundaries, we can remove the logic
that adjusts the offset if the dice roll produced an offset that
puts the kernel right on top of one.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

Mirror arm behaviour for unimplemented syscalls: Below 2048 return
-ENOSYS, above 2048 raise SIGILL.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
[will: Tweak die string to identify as compat syscall]
Signed-off-by: Will Deacon <will.deacon@arm.com>

Pull Xtensa fixes from Max Filippov:
 "Two fixes for reserved memory/DMA buffers allocation in high memory on
  xtensa architecture

   - fix memory accounting when reserved memory is in high memory region

   - fix DMA allocation from high memory"

* tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: support DMA buffers in high memory
  xtensa: fix high memory/reserved memory collision

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes:

   - UAPI data type correction for hyperv

   - correct the cpu cores field in /proc/cpuinfo on CPU hotplug

   - return proper error code in the resctrl file system failure path to
     avoid silent subsequent failures

   - correct a subtle accounting issue in the new vector allocation code
     which went unnoticed for a while and caused suspend/resume
     failures"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
  x86/topology: Fix function name in documentation
  x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
  x86/apic/vector: Handle vector release on CPU unplug correctly
  genirq/matrix: Handle CPU offlining proper
  x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>

Pull perf fix from Thomas Gleixner:
 "A single commit which shuts up a bogus GCC-8 warning"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/oprofile: Fix bogus GCC-8 warning in nmi_setup()

Pull locking fixes from Thomas Gleixner:
 "Three patches to fix memory ordering issues on ALPHA and a comment to
  clarify the usage scope of a mutex internal function"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
  locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
  locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
  locking/mutex: Add comment to __mutex_owner() to deter usage

Pull cleanup patchlet from Thomas Gleixner:
 "A single commit removing a bunch of bogus double semicolons all over
  the tree"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  treewide/trivial: Remove ';;$' typo noise

Pull NFS client bugfixes from Trond Myklebust:

 - fix a broken cast in nfs4_callback_recallany()

 - fix an Oops during NFSv4 migration events

 - make struct nlmclnt_fl_close_lock_ops static

* tag 'nfs-for-4.16-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: make struct nlmclnt_fl_close_lock_ops static
  nfs: system crashes after NFS4ERR_MOVED recovery
  NFSv4: Fix broken cast in nfs4_callback_recallany()

Pull powerpc fixes from Michael Ellerman:

 - Add handling for a missing instruction in our 32-bit BPF JIT so that
   it can be used for seccomp filtering.

 - Add a missing NULL pointer check before a function call in new EEH
   code.

 - Fix an error path in the new ocxl driver to correctly return EFAULT.

 - The support for the new ibm,drc-info device tree property turns out
   to need several fixes, so for now we just stop advertising to
   firmware that we support it until the bugs can be ironed out.

 - One fix for the new drmem code which was incorrectly modifying the
   device tree in place.

 - Finally two fixes for the RFI flush support, so that firmware can
   advertise to us that it should be disabled entirely so as not to
   affect performance.

Thanks to: Bharata B Rao, Frederic Barrat, Juan J. Alvarez, Mark Lord,
Michael Bringmann.

* tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Support firmware disable of RFI flush
  powerpc/pseries: Support firmware disable of RFI flush
  powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2
  powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access
  powerpc/pseries: Revert support for ibm,drc-info devtree property
  powerpc/pseries: Fix duplicate firmware feature for DRC_INFO
  ocxl: Fix potential bad errno on irq allocation
  powerpc/eeh: Fix crashes in eeh_report_resume()

Pull networking fixes from David Miller:

 1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.

 2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.

 3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.

 4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.

 5) Fix potential deadlocks in netfilter getsockopt() code paths, from
    Paolo Abeni.

 6) Netfilter stackpointer size checks really are needed to validate
    user input, from Florian Westphal.

 7) Missing timer init in x_tables, from Paolo Abeni.

 8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.

 9) When an ibmvnic device is brought down then back up again, it can be
    sent queue entries from a previous session, handle this properly
    instead of crashing. From Thomas Falcon.

10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.

11) When we are dumping filters in cls_api, the output SKB is empty, and
    the filter we are dumping is too large for the space in the SKB, we
    should return -EMSGSIZE like other netlink dump operations do.
    Otherwise userland has no signal that is needs to increase the size
    of its read buffer. From Roman Kapl.

12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.

13) Module refcount leak in netlink when a dump start fails, from Jason
    Donenfeld.

14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
    from Eric Dumazet.

15) Releasing bpf per-cpu arraymaps can take a long time, add a
    condtional scheduling point. From Eric Dumazet.

16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
    Daniel Borkmann.

17) Fix page leak in gianfar driver, from Andy Spencer.

18) Missed clearing of estimator scratch buffer, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net_sched: gen_estimator: fix broken estimators based on percpu stats
  gianfar: simplify FCS handling and fix memory leak
  ipv6 sit: work around bogus gcc-8 -Wrestrict warning
  macvlan: fix use-after-free in macvlan_common_newlink()
  bpf, arm64: fix out of bounds access in tail call
  bpf, x64: implement retpoline for tail call
  rxrpc: Fix send in rxrpc_send_data_packet()
  net: aquantia: Fix error handling in aq_pci_probe()
  bpf: fix rcu lockdep warning for lpm_trie map_free callback
  bpf: add schedule points in percpu arrays management
  regulatory: add NUL to request alpha2
  ibmvnic: Fix early release of login buffer
  net/smc9194: Remove bogus CONFIG_MAC reference
  net: ipv4: Set addr_type in hash_keys for forwarded case
  tcp_bbr: better deal with suboptimal GSO
  smsc75xx: fix smsc75xx_set_features()
  netlink: put module reference if dump start fails
  selftests/bpf/test_maps: exit child process without error in ENOMEM case
  selftests/bpf: update gitignore with test_libbpf_open
  selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
  ..

Merge branch 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull security subsystem fixes from James Morris:

 - keys fixes via David Howells:
      "A collection of fixes for Linux keyrings, mostly thanks to Eric
       Biggers:

        - Fix some PKCS#7 verification issues.

        - Fix handling of unsupported crypto in X.509.

        - Fix too-large allocation in big_key"

 - Seccomp updates via Kees Cook:
      "These are fixes for the get_metadata interface that landed during
       -rc1. While the new selftest is strictly not a bug fix, I think
       it's in the same spirit of avoiding bugs"

 - an IMA build fix from Randy Dunlap

* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  integrity/security: fix digsig.c build error with header file
  KEYS: Use individual pages in big_key for crypto buffers
  X.509: fix NULL dereference when restricting key with unsupported_sig
  X.509: fix BUG_ON() when hash algorithm is unsupported
  PKCS#7: fix direct verification of SignerInfo signature
  PKCS#7: fix certificate blacklisting
  PKCS#7: fix certificate chain verification
  seccomp: add a selftest for get_metadata
  ptrace, seccomp: tweak get_metadata behavior slightly
  seccomp, ptrace: switch get_metadata types to arch independent

Pull arm64 fixes from Catalin Marinas:
 "arm64 and perf fixes:

   - build error when accessing MPIDR_HWID_BITMASK from .S

   - fix CTR_EL0 field definitions

   - remove/disable some kernel messages on user faults (unhandled
     signals, unimplemented syscalls)

   - fix kernel page fault in unwind_frame() with function graph tracing

   - fix perf sleeping while atomic errors when booting with ACPI"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix unwind_frame() for filtered out fn for function graph tracing
  arm64: Enforce BBM for huge IO/VMAP mappings
  arm64: perf: correct PMUVer probing
  arm_pmu: acpi: request IRQs up-front
  arm_pmu: note IRQs and PMUs per-cpu
  arm_pmu: explicitly enable/disable SPIs at hotplug
  arm_pmu: acpi: check for mismatched PPIs
  arm_pmu: add armpmu_alloc_atomic()
  arm_pmu: fold platform helpers into platform code
  arm_pmu: kill arm_pmu_platdata
  ARM: ux500: remove PMU IRQ bouncer
  arm64: __show_regs: Only resolve kernel symbols when running at EL1
  arm64: Remove unimplemented syscall log message
  arm64: Disable unhandled signal log messages by default
  arm64: cpufeature: Fix CTR_EL0 field definitions
  arm64: uaccess: Formalise types for access_ok()
  arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files

Pull MIPS fix from James Hogan:
 "A single MIPS fix for mismatching struct compat_flock, resulting in
  bus errors starting Firefox on Debian 8 since 4.13"

* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: Drop spurious __unused in struct compat_flock

Pull printk fixlet from Petr Mladek:
 "People expect to see the real pointer value for %px.

  Let's substitute '(null)' only for the other %p? format modifiers that
  need to deference the pointer"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  vsprintf: avoid misleading "(null)" for %px

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes, one v4.16 regression fix, and two documentation fixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Consider SCL GPIO optional
  i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
  i2c: bcm2835: Set up the rising/falling edge delays
  i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
  i2c: designware: must wait for enable

Pull SCSI fixes from James Bottomley:
 "These are mostly fixes for problems with merge window code.

  In addition we have one doc update (alua) and two dead code removals
  (aiclib and octogon) a spurious assignment removal (csiostor) and a
  performance improvement for storvsc involving better interrupt
  spreading and increasing the command per lun handling"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla4xxx: skip error recovery in case of register disconnect.
  scsi: aacraid: fix shutdown crash when init fails
  scsi: qedi: Cleanup local str variable
  scsi: qedi: Fix truncation of CHAP name and secret
  scsi: qla2xxx: Fix incorrect handle for abort IOCB
  scsi: qla2xxx: Fix double free bug after firmware timeout
  scsi: storvsc: Increase cmd_per_lun for higher speed devices
  scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
  scsi: scsi_dh: Document alua_rtpg_queue() arguments
  scsi: Remove Makefile entry for oktagon files
  scsi: aic7xxx: remove aiclib.c
  scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
  scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
  scsi: sym53c8xx_2: iterator underflow in sym_getsync()
  scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
  scsi: csiostor: remove redundant assignment to pointer 'ln'
  scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
  scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
  scsi: qla2xxx: Fix memory corruption during hba reset test
  scsi: mpt3sas: fix an out of bound write