- 04 Mar, 2016 28 commits
-
-
Andy Shevchenko authored
[ Upstream commit ee1cdcda ] The commit 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") re-enabled BLOCK interrupts with regard to make cyclic transfers work. However, this change becomes a regression for non-cyclic transfers as interrupt counters under stress test had been grown enormously (approximately per 4-5 bytes in the UART loop back test). Taking into consideration above enable BLOCK interrupts if and only if channel is programmed to perform cyclic transfer. Fixes: 2895b2ca ("dmaengine: dw: fix cyclic transfer callbacks") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Mans Rullgard <mans@mansr.com> Tested-by:
Viresh Kumar <viresh.kumar@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
Takashi Iwai authored
[ Upstream commit 0b8c8219 ] The commit [991f86d7: ALSA: hda - Flush the pending probe work at remove] introduced the sync of async probe work at remove for fixing the race. However, this may lead to another hangup when the module removal is performed quickly before starting the probe work, because it issues flush_work() and it's blocked forever. The workaround is to use cancel_work_sync() instead of flush_work() there. Fixes: 991f86d7 ('ALSA: hda - Flush the pending probe work at remove') Cc: <stable@vger.kernel.org> # v3.17+ Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit d99a36f4 ] When multiple concurrent writes happen on the ALSA sequencer device right after the open, it may try to allocate vmalloc buffer for each write and leak some of them. It's because the presence check and the assignment of the buffer is done outside the spinlock for the pool. The fix is to move the check and the assignment into the spinlock. (The current implementation is suboptimal, as there can be multiple unnecessary vmallocs because the allocation is done before the check in the spinlock. But the pool size is already checked beforehand, so this isn't a big problem; that is, the only possible path is the multiple writes before any pool assignment, and practically seen, the current coverage should be "good enough".) The issue was triggered by syzkaller fuzzer. BugLink: http://lkml.kernel.org/r/CACT4Y+bSzazpXNvtAr=WXaL8hptqjHwqEyFA+VN2AWEx=aurkg@mail.gmail.comReported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Gavin Shan authored
[ Upstream commit 05ba75f8 ] When PE is created, its primary bus is cached to pe->bus. At later point, the cached primary bus is returned from eeh_pe_bus_get(). However, we could get stale cached primary bus and run into kernel crash in one case: full hotplug as part of fenced PHB error recovery releases all PCI busses under the PHB at unplugging time and recreate them at plugging time. pe->bus is still dereferencing the PCI bus that was released. This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity of pe->bus. pe->bus is updated when its first child EEH device is online and the flag is set. Before unplugging in full hotplug for error recovery, the flag is cleared. Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE") Cc: stable@vger.kernel.org #v3.11+ Reported-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Reported-by:
Pradipta Ghosh <pradghos@in.ibm.com> Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Tested-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Andrey Konovalov authored
[ Upstream commit 07d86ca9 ] The 'umidi' object will be free'd on the error path by snd_usbmidi_free() when tearing down the rawmidi interface. So we shouldn't try to free it in snd_usbmidi_create() after having registered the rawmidi interface. Found by KASAN. Signed-off-by:
Andrey Konovalov <andreyknvl@gmail.com> Acked-by:
Clemens Ladisch <clemens@ladisch.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hannes Reinecke authored
[ Upstream commit 2d99b55d ] Commit 35dc2483 introduced a check for current->mm to see if we have a user space context and only copies data if we do. Now if an IO gets interrupted by a signal data isn't copied into user space any more (as we don't have a user space context) but user space isn't notified about it. This patch modifies the behaviour to return -EINTR from bio_uncopy_user() to notify userland that a signal has interrupted the syscall, otherwise it could lead to a situation where the caller may get a buffer with no data returned. This can be reproduced by issuing SG_IO ioctl()s in one thread while constantly sending signals to it. Fixes: 35dc2483 [SCSI] sg: Fix user memory corruption when SG_IO is interrupted by a signal Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Hannes Reinecke <hare@suse.de> Cc: stable@vger.kernel.org # v.3.11+ Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Ryan Ware authored
[ Upstream commit 613317bd ] This patch fixes vulnerability CVE-2016-2085. The problem exists because the vm_verify_hmac() function includes a use of memcmp(). Unfortunately, this allows timing side channel attacks; specifically a MAC forgery complexity drop from 2^128 to 2^12. This patch changes the memcmp() to the cryptographically safe crypto_memneq(). Reported-by:
Xiaofei Rex Guo <xiaofei.rex.guo@intel.com> Signed-off-by:
Ryan Ware <ware@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
James Morris <james.l.morris@oracle.com> Signed-off-by:
-
Eryu Guan authored
[ Upstream commit bcff2488 ] I notice ext4/307 fails occasionally on ppc64 host, reporting md5 checksum mismatch after moving data from original file to donor file. The reason is that move_extent_per_page() calls __block_write_begin() and block_commit_write() to write saved data from original inode blocks to donor inode blocks, but __block_write_begin() not only maps buffer heads but also reads block content from disk if the size is not block size aligned. At this time the physical block number in mapped buffer head is pointing to the donor file not the original file, and that results in reading wrong data to page, which get written to disk in following block_commit_write call. This also can be reproduced by the following script on 1k block size ext4 on x86_64 host: mnt=/mnt/ext4 donorfile=$mnt/donor testfile=$mnt/testfile e4compact=~/xfstests/src/e4compact rm -f $donorfile $testfile # reserve space for donor file, written by 0xaa and sync to disk to # avoid EBUSY on EXT4_IOC_MOVE_EXT xfs_io -fc "pwrite -S 0xaa 0 1m" -c "fsync" $donorfile # create test file written by 0xbb xfs_io -fc "pwrite -S 0xbb 0 1023" -c "fsync" $testfile # compute initial md5sum md5sum $testfile | tee md5sum.txt # drop cache, force e4compact to read data from disk echo 3 > /proc/sys/vm/drop_caches # test defrag echo "$testfile" | $e4compact -i -v -f $donorfile # check md5sum md5sum -c md5sum.txt Fix it by creating & mapping buffer heads only but not reading blocks from disk, because all the data in page is guaranteed to be up-to-date in mext_page_mkuptodate(). Cc: stable@vger.kernel.org Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Insu Yun authored
[ Upstream commit 46901760 ] Since sizeof(ext_new_group_data) > sizeof(ext_new_flex_group_data), integer overflow could be happened. Therefore, need to fix integer overflow sanitization. Cc: stable@vger.kernel.org Signed-off-by:
Insu Yun <wuninsu@gmail.com> Signed-off-by:
-
David Sterba authored
[ Upstream commit bc4ef759 ] The value of ctx->pos in the last readdir call is supposed to be set to INT_MAX due to 32bit compatibility, unless 'pos' is intentially set to a larger value, then it's LLONG_MAX. There's a report from PaX SIZE_OVERFLOW plugin that "ctx->pos++" overflows (https://forums.grsecurity.net/viewtopic.php?f=1&t=4284), on a 64bit arch, where the value is 0x7fffffffffffffff ie. LLONG_MAX before the increment. We can get to that situation like that: * emit all regular readdir entries * still in the same call to readdir, bump the last pos to INT_MAX * next call to readdir will not emit any entries, but will reach the bump code again, finds pos to be INT_MAX and sets it to LLONG_MAX Normally this is not a problem, but if we call readdir again, we'll find 'pos' set to LLONG_MAX and the unconditional increment will overflow. The report from Victor at (http://thread.gmane.org/gmane.comp.file-systems.btrfs/49500) with debugging print shows that pattern: Overflow: e Overflow: 7fffffff Overflow: 7fffffffffffffff PAX: size overflow detected in function btrfs_real_readdir fs/btrfs/inode.c:5760 cicus.935_282 max, count: 9, decl: pos; num: 0; context: dir_context; CPU: 0 PID: 2630 Comm: polkitd Not tainted 4.2.3-grsec #1 Hardware name: Gigabyte Technology Co., Ltd. H81ND2H/H81ND2H, BIOS F3 08/11/2015 ffffffff81901608 0000000000000000 ffffffff819015e6 ffffc90004973d48 ffffffff81742f0f 0000000000000007 ffffffff81901608 ffffc90004973d78 ffffffff811cb706 0000000000000000 ffff8800d47359e0 ffffc90004973ed8 Call Trace: [<ffffffff81742f0f>] dump_stack+0x4c/0x7f [<ffffffff811cb706>] report_size_overflow+0x36/0x40 [<ffffffff812ef0bc>] btrfs_real_readdir+0x69c/0x6d0 [<ffffffff811dafc8>] iterate_dir+0xa8/0x150 [<ffffffff811e6d8d>] ? __fget_light+0x2d/0x70 [<ffffffff811dba3a>] SyS_getdents+0xba/0x1c0 Overflow: 1a [<ffffffff811db070>] ? iterate_dir+0x150/0x150 [<ffffffff81749b69>] entry_SYSCALL_64_fastpath+0x12/0x83 The jump from 7fffffff to 7fffffffffffffff happens when new dir entries are not yet synced and are processed from the delayed list. Then the code could go to the bump section again even though it might not emit any new dir entries from the delayed list. The fix avoids entering the "bump" section again once we've finished emitting the entries, both for synced and delayed entries. References: https://forums.grsecurity.net/viewtopic.php?f=1&t=4284Reported-by:
Victor <services@swwu.com> CC: stable@vger.kernel.org Signed-off-by:
David Sterba <dsterba@suse.com> Tested-by:
Holger Hoffstätte <holger.hoffstaette@googlemail.com> Signed-off-by:
Chris Mason <clm@fb.com> Signed-off-by:
-
Linus Walleij authored
[ Upstream commit e972c374 ] Since the dawn of time the ICST code has only supported divide by one or hang in an eternal loop. Luckily we were always dividing by one because the reference frequency for the systems using the ICSTs is 24MHz and the [min,max] values for the PLL input if [10,320] MHz for ICST307 and [6,200] for ICST525, so the loop will always terminate immediately without assigning any divisor for the reference frequency. But for the code to make sense, let's insert the missing i++ Reported-by:
David Binderman <dcb314@hotmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Stefan Haberland authored
[ Upstream commit 9d862aba ] Add refcount to the DASD device when a summary unit check worker is scheduled. This prevents that the device is set offline with worker in place. Cc: stable@vger.kernel.org Signed-off-by:
Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Stefan Haberland authored
[ Upstream commit 020bf042 ] The channel checks the specified length and the provided amount of data for CCWs and provides an incorrect length error if the size does not match. Under z/VM with simulation activated the length may get changed. Having the suppress length indication bit set is stated as good CCW coding practice and avoids errors under z/VM. Cc: stable@vger.kernel.org Signed-off-by:
-
Anton Protopopov authored
[ Upstream commit 4b550af5 ] The setup_ntlmv2_rsp() function may return positive value ENOMEM instead of -ENOMEM in case of kmalloc failure. Signed-off-by:
Anton Protopopov <a.s.protopopov@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Nicolai Hähnle authored
[ Upstream commit f6ff4f67 ] An arbitrary amount of time can pass between spin_unlock and radeon_fence_wait_any, so we need to ensure that nobody frees the fences from under us. Based on the analogous fix for amdgpu. Signed-off-by:
Nicolai Hähnle <nicolai.haehnle@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Tejun Heo authored
[ Upstream commit d6e022f1 ] When looking up the pool_workqueue to use for an unbound workqueue, workqueue assumes that the target CPU is always bound to a valid NUMA node. However, currently, when a CPU goes offline, the mapping is destroyed and cpu_to_node() returns NUMA_NO_NODE. This has always been broken but hasn't triggered often enough before 874bbfe6 ("workqueue: make sure delayed work run in local cpu"). After the commit, workqueue forcifully assigns the local CPU for delayed work items without explicit target CPU to fix a different issue. This widens the window where CPU can go offline while a delayed work item is pending causing delayed work items dispatched with target CPU set to an already offlined CPU. The resulting NUMA_NO_NODE mapping makes workqueue try to queue the work item on a NULL pool_workqueue and thus crash. While 874bbfe6 has been reverted for a different reason making the bug less visible again, it can still happen. Fix it by mapping NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node(). This is a temporary workaround. The long term solution is keeping CPU -> NODE mapping stable across CPU off/online cycles which is being worked on. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Tang Chen <tangchen@cn.fujitsu.com> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Len Brown <len.brown@intel.com> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/g/1454424264.11183.46.camel@gmail.com Link: http://lkml.kernel.org/g/1453702100-2597-1-git-send-email-tangchen@cn.fujitsu.comSigned-off-by:
-
Lai Jiangshan authored
[ Upstream commit 5b95e1af ] Current wq_pool_mutex doesn't proctect the attrs-installation, it results that ->unbound_attrs, ->numa_pwq_tbl[] and ->dfl_pwq can only be accessed under wq->mutex and causes some inconveniences. Example, wq_update_unbound_numa() has to acquire wq->mutex before fetching the wq->unbound_attrs->no_numa and the old_pwq. attrs-installation is a short operation, so this change will no cause any latency for other operations which also acquire the wq_pool_mutex. The only unprotected attrs-installation code is in apply_workqueue_attrs(), so this patch touches code less than comments. It is also a preparation patch for next several patches which read wq->unbound_attrs, wq->numa_pwq_tbl[] and wq->dfl_pwq with only wq_pool_mutex held. Signed-off-by:
Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by:
-
Lai Jiangshan authored
[ Upstream commit 2d5f0764 ] Current apply_workqueue_attrs() includes pwqs-allocation and pwqs-installation, so when we batch multiple apply_workqueue_attrs()s as a transaction, we can't ensure the transaction must succeed or fail as a complete unit. To solve this, we split apply_workqueue_attrs() into three stages. The first stage does the preparation: allocation memory, pwqs. The second stage does the attrs-installaion and pwqs-installation. The third stage frees the allocated memory and (old or unused) pwqs. As the result, batching multiple apply_workqueue_attrs()s can succeed or fail as a complete unit: 1) batch do all the first stage for all the workqueues 2) only commit all when all the above succeed. This patch is a preparation for the next patch ("Allow modifying low level unbound workqueue cpumask") which will do a multiple apply_workqueue_attrs(). The patch doesn't have functionality changed except two minor adjustment: 1) free_unbound_pwq() for the error path is removed, we use the heavier version put_pwq_unlocked() instead since the error path is rare. this adjustment simplifies the code. 2) the memory-allocation is also moved into wq_pool_mutex. this is needed to avoid to do the further splitting. tj: minor updates to comments. Suggested-by:
-
Alexandra Yates authored
[ Upstream commit 342decff ] Adding Intel codename DNV platform device IDs for SATA. Signed-off-by:
Alexandra Yates <alexandra.yates@linux.intel.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 58a66dba ] If we reload phy-twl4030-usb, we get a warning about unbalanced pm_runtime_enable. Let's fix the issue and also fix idling of the device on unload before we attempt to shut it down. If we don't properly idle the PHY before shutting it down on removal, the twl4030 ends up consuming about 62mW of extra power compared to running idle with the module loaded. Cc: stable@vger.kernel.org Cc: Bin Liu <b-liu@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: NeilBrown <neil@brown.name> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit b241d31e ] Otherwise rmmod omap2430; rmmod phy-twl4030-usb; modprobe omap2430 will try to use a non-existing phy and oops: Unable to handle kernel paging request at virtual address b6f7c1f0 ... [<c048a284>] (devm_usb_get_phy_by_node) from [<bf0758ac>] (omap2430_musb_init+0x44/0x2b4 [omap2430]) [<bf0758ac>] (omap2430_musb_init [omap2430]) from [<bf055ec0>] (musb_init_controller+0x194/0x878 [musb_hdrc]) Cc: stable@vger.kernel.org Cc: Bin Liu <b-liu@ti.com> Cc: Felipe Balbi <balbi@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: NeilBrown <neil@brown.name> Signed-off-by:
-
Shawn Lin authored
[ Upstream commit b82fcabe ] If phy_pm_runtime_get_sync failed but we already enable regulator, current code return directly without doing regulator_disable. This patch fix this problem and cleanup err handle of phy_power_on to be more readable. Fixes: 3be88125 ("phy: core: Support regulator ...") Cc: <stable@vger.kernel.org> # v3.18+ Cc: Roger Quadros <rogerq@ti.com> Cc: Axel Lin <axel.lin@ingics.com> Signed-off-by:
Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by:
-
Tejun Heo authored
[ Upstream commit 041bd12e ] This reverts commit 874bbfe6. Workqueue used to implicity guarantee that work items queued without explicit CPU specified are put on the local CPU. Recent changes in timer broke the guarantee and led to vmstat breakage which was fixed by 176bed1d ("vmstat: explicitly schedule per-cpu work on the CPU we need it to run on"). vmstat is the most likely to expose the issue and it's quite possible that there are other similar problems which are a lot more difficult to trigger. As a preventive measure, 874bbfe6 ("workqueue: make sure delayed work run in local cpu") was applied to restore the local CPU guarnatee. Unfortunately, the change exposed a bug in timer code which got fixed by 22b886dd ("timers: Use proper base migration in add_timer_on()"). Due to code restructuring, the commit couldn't be backported beyond certain point and stable kernels which only had 874bbfe6 started crashing. The local CPU guarantee was accidental more than anything else and we want to get rid of it anyway. As, with the vmstat case fixed, 874bbfe6 is causing more problems than it's fixing, it has been decided to take the chance and officially break the guarantee by reverting the commit. A debug feature will be added to force foreign CPU assignment to expose cases relying on the guarantee and fixes for the individual cases will be backported to stable as necessary. Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 4dff5c7b ] snd_timer_user_read() has a potential race among parallel reads, as qhead and qused are updated outside the critical section due to copy_to_user() calls. Move them into the critical section, and also sanitize the relevant code a bit. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 2ebab40e ] The hda_jack_tbl entries are managed by snd_array for allowing multiple jacks. It's good per se, but the problem is that struct hda_jack_callback keeps the hda_jack_tbl pointer. Since snd_array doesn't preserve each pointer at resizing the array, we can't keep the original pointer but have to deduce the pointer at each time via snd_array_entry() instead. Actually, this resulted in the deference to the wrong pointer on codecs that have many pins such as CS4208. This patch replaces the pointer to the NID value as the search key. As an unexpected good side effect, this even simplifies the code, as only NID is needed in most cases. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit ed8b1d6d ] A slave timer element also unlinks at snd_timer_stop() but it takes only slave_active_lock. When a slave is assigned to a master, however, this may become a race against the master's interrupt handling, eventually resulting in a list corruption. The actual bug could be seen with a syzkaller fuzzer test case in BugLink below. As a fix, we need to take timeri->timer->lock when timer isn't NULL, i.e. assigned to a master, while the assignment to a master itself is protected by slave_active_lock. BugLink: http://lkml.kernel.org/r/CACT4Y+Y_Bm+7epAb=8Wi=AaWd+DYS7qawX52qxdCfOfY49vozQ@mail.gmail.com Cc: <stable@vger.kernel.org> Signed-off-by:
-
Linus Walleij authored
[ Upstream commit 5070fb14 ] When trying to set the ICST 307 clock to 25174000 Hz I ran into this arithmetic error: the icst_hz_to_vco() correctly figure out DIVIDE=2, RDW=100 and VDW=99 yielding a frequency of 25174000 Hz out of the VCO. (I replicated the icst_hz() function in a spreadsheet to verify this.) However, when I called icst_hz() on these VCO settings it would instead return 4122709 Hz. This causes an error in the common clock driver for ICST as the common clock framework will call .round_rate() on the clock which will utilize icst_hz_to_vco() followed by icst_hz() suggesting the erroneous frequency, and then the clock gets set to this. The error did not manifest in the old clock framework since this high frequency was only used by the CLCD, which calls clk_set_rate() without first calling clk_round_rate() and since the old clock framework would not call clk_round_rate() before setting the frequency, the correct values propagated into the VCO. After some experimenting I figured out that it was due to a simple arithmetic overflow: the divisor for 24Mhz reference frequency as reference becomes 24000000*2*(99+8)=0x132212400 and the "1" in bit 32 overflows and is lost. But introducing an explicit 64-by-32 bit do_div() and casting the divisor into (u64) we get the right frequency back, and the right frequency gets set. Tested on the ARM Versatile. Cc: stable@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: Pawel Moll <pawel.moll@arm.com> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 117159f0 ] In snd_timer_notify1(), the wrong timer instance was passed for slave ccallback function. This leads to the access to the wrong data when an incompatible master is handled (e.g. the master is the sequencer timer and the slave is a user timer), as spotted by syzkaller fuzzer. This patch fixes that wrong assignment. BugLink: http://lkml.kernel.org/r/CACT4Y+Y_Bm+7epAb=8Wi=AaWd+DYS7qawX52qxdCfOfY49vozQ@mail.gmail.comReported-by:
-
- 28 Feb, 2016 12 commits
-
-
Jani Nikula authored
[ Upstream commit 26f6f2d3 ] Since sequence block v2 the second byte contains flags other than just pull up/down. Don't pass arbitrary data to the sideband interface. The rest may or may not work for sequence block v2, but there should be no harm done. Cc: stable@vger.kernel.org Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/ebe3c2eee623afc4b3a134533b01f8d591d13f32.1454582914.git.jani.nikula@intel.com (cherry picked from commit 4e1c63e3) Signed-off-by:
-
Jani Nikula authored
[ Upstream commit 4db3a244 ] Do not blindly trust the VBT data used for indexing. Cc: stable@vger.kernel.org Reviewed-by:
-
Takashi Iwai authored
[ Upstream commit ddce57a6 ] Currently the selected timer backend is referred at any moment from the running PCM callbacks. When the backend is switched, it's possible to lead to inconsistency from the running backend. This was pointed by syzkaller fuzzer, and the commit [7ee96216: ALSA: dummy: Disable switching timer backend via sysfs] disabled the dynamic switching for avoiding the crash. This patch improves the handling of timer backend switching. It keeps the reference to the selected backend during the whole operation of an opened stream so that it won't be changed by other streams. Together with this change, the hrtimer parameter is reenabled as writable now. NOTE: this patch also turned out to fix the still remaining race. Namely, ops was still replaced dynamically at dummy_pcm_open: static int dummy_pcm_open(struct snd_pcm_substream *substream) { .... dummy->timer_ops = &dummy_systimer_ops; if (hrtimer) dummy->timer_ops = &dummy_hrtimer_ops; Since dummy->timer_ops is common among all streams, and when the replacement happens during accesses of other streams, it may lead to a crash. This was actually triggered by syzkaller fuzzer and KASAN. This patch rewrites the code not to use the ops shared by all streams any longer, too. BugLink: http://lkml.kernel.org/r/CACT4Y+aZ+xisrpuM6cOXbL21DuM0yVxPYXf4cD4Md9uw0C3dBQ@mail.gmail.comReported-by:
-
James Bottomley authored
[ Upstream commit 00cd29b7 ] The starting node for a klist iteration is often passed in from somewhere way above the klist infrastructure, meaning there's no guarantee the node is still on the list. We've seen this in SCSI where we use bus_find_device() to iterate through a list of devices. In the face of heavy hotplug activity, the last device returned by bus_find_device() can be removed before the next call. This leads to Dec 3 13:22:02 localhost kernel: WARNING: CPU: 2 PID: 28073 at include/linux/kref.h:47 klist_iter_init_node+0x3d/0x50() Dec 3 13:22:02 localhost kernel: Modules linked in: scsi_debug x86_pkg_temp_thermal kvm_intel kvm irqbypass crc32c_intel joydev iTCO_wdt dcdbas ipmi_devintf acpi_power_meter iTCO_vendor_support ipmi_si imsghandler pcspkr wmi acpi_cpufreq tpm_tis tpm shpchp lpc_ich mfd_core nfsd nfs_acl lockd grace sunrpc tg3 ptp pps_core Dec 3 13:22:02 localhost kernel: CPU: 2 PID: 28073 Comm: cat Not tainted 4.4.0-rc1+ #2 Dec 3 13:22:02 localhost kernel: Hardware name: Dell Inc. PowerEdge R320/08VT7V, BIOS 2.0.22 11/19/2013 Dec 3 13:22:02 localhost kernel: ffffffff81a20e77 ffff880613acfd18 ffffffff81321eef 0000000000000000 Dec 3 13:22:02 localhost kernel: ffff880613acfd50 ffffffff8107ca52 ffff88061176b198 0000000000000000 Dec 3 13:22:02 localhost kernel: ffffffff814542b0 ffff880610cfb100 ffff88061176b198 ffff880613acfd60 Dec 3 13:22:02 localhost kernel: Call Trace: Dec 3 13:22:02 localhost kernel: [<ffffffff81321eef>] dump_stack+0x44/0x55 Dec 3 13:22:02 localhost kernel: [<ffffffff8107ca52>] warn_slowpath_common+0x82/0xc0 Dec 3 13:22:02 localhost kernel: [<ffffffff814542b0>] ? proc_scsi_show+0x20/0x20 Dec 3 13:22:02 localhost kernel: [<ffffffff8107cb4a>] warn_slowpath_null+0x1a/0x20 Dec 3 13:22:02 localhost kernel: [<ffffffff8167225d>] klist_iter_init_node+0x3d/0x50 Dec 3 13:22:02 localhost kernel: [<ffffffff81421d41>] bus_find_device+0x51/0xb0 Dec 3 13:22:02 localhost kernel: [<ffffffff814545ad>] scsi_seq_next+0x2d/0x40 [...] And an eventual crash. It can actually occur in any hotplug system which has a device finder and a starting device. We can fix this globally by making sure the starting node for klist_iter_init_node() is actually a member of the list before using it (and by starting from the beginning if it isn't). Reported-by:
Ewan D. Milne <emilne@redhat.com> Tested-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit c44d9b11 ] Some Sony VAIO AiO models (VGC-JS4EF and VGC-JS25G, both with PCI SSID 104d:9044) need the same quirk to make the speaker working properly. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=112031 Cc: <stable@vger.kernel.org> Signed-off-by:
-
Herton R. Krzesinski authored
[ Upstream commit 1f55c718 ] Considering current pty code and multiple devpts instances, it's possible to umount a devpts file system while a program still has /dev/tty opened pointing to a previosuly closed pty pair in that instance. In the case all ptmx and pts/N files are closed, umount can be done. If the program closes /dev/tty after umount is done, devpts_kill_index will use now an invalid super_block, which was already destroyed in the umount operation after running ->kill_sb. This is another "use after free" type of issue, but now related to the allocated super_block instance. To avoid the problem (warning at ida_remove and potential crashes) for this specific case, I added two functions in devpts which grabs additional references to the super_block, which pty code now uses so it makes sure the super block structure is still valid until pty shutdown is done. I also moved the additional inode references to the same functions, which also covered similar case with inode being freed before /dev/tty final close/shutdown. Signed-off-by:
Herton R. Krzesinski <herton@redhat.com> Cc: stable@vger.kernel.org # 2.6.29+ Reviewed-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Herton R. Krzesinski authored
[ Upstream commit 2831c89f ] This change fixes a bug for a corner case where we have the the last release from a pty master/slave coming from a previously opened /dev/tty file. When this happens, the tty->driver_data can be stale, due to all ptmx or pts/N files having already been closed before (and thus the inode related to these files, which tty->driver_data points to, being already freed/destroyed). The fix here is to keep a reference on the opened master ptmx inode. We maintain the inode referenced until the final pty_unix98_shutdown, and only pass this inode to devpts_kill_index. Signed-off-by:
-
Jeremy McNicoll authored
[ Upstream commit 7dde5578 ] WCH382 2S board is a PCIe card with 2 DB9 COM ports detected as Serial controller: Device 1c00:3253 (rev 10) (prog-if 05 [16850]) Signed-off-by:
Jeremy McNicoll <jmcnicol@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Peter Hurley authored
[ Upstream commit 308bbc9a ] The omap-serial driver emulates RS485 delays using software timers, but neglects to clamp the input values from the unprivileged ioctl(TIOCSRS485). Because the software implementation busy-waits, malicious userspace could stall the cpu for ~49 days. Clamp the input values to < 100ms. Fixes: 4a0ac0f5 ("OMAP: add RS485 support") Cc: <stable@vger.kernel.org> # 3.12+ Signed-off-by:
-
Quinn Tran authored
[ Upstream commit 84e32a06 ] As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() or pci_enable_msi_exact() and pci_enable_msix_range() or pci_enable_msix_exact() interfaces. Log message code 0x00c6 preserved, although it is reported after successful call to pci_enable_msix_range(), not before possibly unsuccessful call to pci_enable_msix(). Consumers of the error code should not notice the difference. Signed-off-by:
Alexander Gordeev <agordeev@redhat.com> Acked-by:
Chad Dupuis <chad.dupuis@qlogic.com> Cc: qla2xxx-upstream@qlogic.com Cc: linux-scsi@vger.kernel.org Cc: linux-pci@vger.kernel.org Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Cyrille Pitchen authored
[ Upstream commit ee36c87a ] commit c033042a upstream. clk_prepare()/clk_unprepare() must not be called within atomic context. This patch calls clk_prepare() once for all from atmel_sha_probe() and clk_unprepare() from atmel_sha_remove(). Then calls of clk_prepare_enable()/clk_disable_unprepare() were replaced by calls of clk_enable()/clk_disable(). Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Reported-by:
Matthias Mayr <matthias.mayr@student.kit.edu> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
LABBE Corentin authored
[ Upstream commit 9d83d299 ] clk_prepare_enable() can fail so add a check for this and return the error code if it fails. Signed-off-by:
LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by:
-
