The array bio_in_progress[2] only have chance to be increased and
decreased with ssd mode. For pmem mode, they are not involved at all.
So skip writecache_wait_for_ios in writecache_flush for pmem.
Suggested-by: Doris Yu <tyu1@lenovo.com>
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct dm_stat {
	...
        struct dm_stat_shared stat_shared[0];
};

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.

So, replace the following form:

sizeof(struct dm_stat) + (size_t)n_entries * sizeof(struct dm_stat_shared)

with:

struct_size(s, stat_shared, n_entries)

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Only the ESSIV IV generation mode used to use cc->cipher so it could
instantiate the bare cipher used to encrypt the IV. However, this is
now taken care of by the ESSIV template, and so no users of cc->cipher
remain. So remove it altogether.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Replace the explicit ESSIV handling in the dm-crypt driver with calls
into the crypto API, which now possesses the capability to perform
this processing within the crypto subsystem.

Note that we reorder the AEAD cipher_api string parsing with the TFM
instantiation: this is needed because cipher_api is mangled by the
ESSIV handling, and throws off the parsing of "authenc(" otherwise.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Implement a template that wraps a (skcipher,shash) or (aead,shash) tuple
so that we can consolidate the ESSIV handling in fscrypt and dm-crypt and
move it into the crypto API. This will result in better test coverage, and
will allow future changes to make the bare cipher interface internal to the
crypto subsystem, in order to increase robustness of the API against misuse.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

The function sm_find_free() just returns -ENOSPC and 0.
So remove lone caller's check for some other error.
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct mirror_set {
	...
        struct mirror mirror[0];
};

size = sizeof(struct mirror_set) + count * sizeof(struct mirror);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, mirror, count), GFP_KERNEL)

Notice that, in this case, variable len is not necessary, hence it
is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

During the process of writeback, the blocks, which have been placed in wbl.list
for writeback soon, are partially ordered for the contiguous ones.

When writeback_all has been set, for most cases, also by default, there will be
a lot of blocks in pmem need to writeback at the same time.
For this case, we could optimize the performance by sorting all blocks in
wbl.list. writecache_writeback doesn't need to get blocks from the tail of
wc->lru, whereas from the first rb_node from the rb_tree.

The benefit is that, writecache_writeback doesn't need to have any cost to sort
the blocks, because of all blocks are incremental originally in rb_tree.
There will be a writecache_flush when writeback_all begins to work, that will
eliminate duplicate blocks in cache by committed/uncommitted.

Testing platform: Thinksystem SR630 with persistent memory.
The cache comes from pmem, which has 1006MB size. The origin device is HDD, 2GB
of which for using.

Testing steps:
 1) dmsetup create mycache --table '0 4194304 writecache p /dev/sdb1 /dev/pmem4  4096 0'
 2) fio -filename=/dev/mapper/mycache -direct=1 -iodepth=20 -rw=randwrite
 -ioengine=libaio -bs=4k -loops=1  -size=2g -group_reporting -name=mytest1
 3) time dmsetup message /dev/mapper/mycache 0 flush

Here is the results below,
With the patch:
 # fio -filename=/dev/mapper/mycache -direct=1 -iodepth=20 -rw=randwrite
 -ioengine=libaio -bs=4k -loops=1  -size=2g -group_reporting -name=mytest1
   iops        : min= 1582, max=199470, avg=5305.94, stdev=21273.44, samples=197
 # time dmsetup message /dev/mapper/mycache 0 flush
real	0m44.020s
user	0m0.002s
sys	0m0.003s

Without the patch:
 # fio -filename=/dev/mapper/mycache -direct=1 -iodepth=20 -rw=randwrite
 -ioengine=libaio -bs=4k -loops=1  -size=2g -group_reporting -name=mytest1
   iops        : min= 1202, max=197650, avg=4968.67, stdev=20480.17, samples=211
 # time dmsetup message /dev/mapper/mycache 0 flush
real	1m39.221s
user	0m0.001s
sys	0m0.003s

I also have checked the data accuracy with this patch by making EXT4 filesystem
on mycache, then mount it for checking md5 of files on that.
The test result is positive, with this patch it could save more than half of time
when writeback_all.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

In function writecache_writeback, entries g and f has same original
sector only happens at entry f has been committed, but entry g has
NOT yet.

The probability of this happening is very low in the following
256 blocks at most of entry e.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

The stucture member pointer page in writeback_struct never has been
used actually. Remove it.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Commit 75d66ffb ("dm zoned: properly
handle backing device failure") triggers a coverity warning:

*** CID 1452808:  Memory - illegal accesses  (USE_AFTER_FREE)
/drivers/md/dm-zoned-target.c: 137 in dmz_submit_bio()
131             clone->bi_private = bioctx;
132
133             bio_advance(bio, clone->bi_iter.bi_size);
134
135             refcount_inc(&bioctx->ref);
136             generic_make_request(clone);
>>>     CID 1452808:  Memory - illegal accesses  (USE_AFTER_FREE)
>>>     Dereferencing freed pointer "clone".
137             if (clone->bi_status == BLK_STS_IOERR)
138                     return -EIO;
139
140             if (bio_op(bio) == REQ_OP_WRITE && dmz_is_seq(zone))
141                     zone->wp_block += nr_blocks;
142

The "clone" bio may be processed and freed before the check
"clone->bi_status == BLK_STS_IOERR" - so this check can access invalid
memory.

Fixes: 75d66ffb ("dm zoned: properly handle backing device failure")
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

The verification is to support cases where the root hash is not secured
by Trusted Boot, UEFI Secureboot or similar technologies.

One of the use cases for this is for dm-verity volumes mounted after
boot, the root hash provided during the creation of the dm-verity volume
has to be secure and thus in-kernel validation implemented here will be
used before we trust the root hash and allow the block device to be
created.

The signature being provided for verification must verify the root hash
and must be trusted by the builtin keyring for verification to succeed.

The hash is added as a key of type "user" and the description is passed
to the kernel so it can look it up and use it for verification.

Adds CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG which can be turned on if root
hash verification is needed.

Kernel commandline dm_verity module parameter 'require_signatures' will
indicate whether to force root hash signature verification (for all dm
verity volumes).
Signed-off-by: Jaskaran Khurana <jaskarankhurana@linux.microsoft.com>
Tested-and-Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Instead of instantiating a separate cipher to perform the encryption
needed to produce the IV, reuse the skcipher used for the block data
and invoke it one additional time for each block to encrypt a zero
vector and use the output as the IV.

For CBC mode, this is equivalent to using the bare block cipher, but
without the risk of ending up with a non-time invariant implementation
of AES when the skcipher itself is time variant (e.g., arm64 without
Crypto Extensions has a NEON based time invariant implementation of
cbc(aes) but no time invariant implementation of the core cipher other
than aes-ti, which is not enabled by default).

This approach is a compromise between dm-crypt API flexibility and
reducing dependence on parts of the crypto API that should not usually
be exposed to other subsystems, such as the bare cipher API.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Currently, if we pass too high sector number to dm_table_find_target, it
returns zeroed dm_target structure and callers test if the structure is
zeroed with the macro dm_target_is_valid.

However, returning NULL is common practice to indicate errors.

This patch refactors the dm code, so that dm_table_find_target returns
NULL and its callers test the returned value for NULL. The macro
dm_target_is_valid is deleted. In alloc_targets, we no longer allocate an
extra zeroed target.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

If the sector number is too high, dm_table_find_target() should return a
pointer to a zeroed dm_target structure (the caller should test it with
dm_target_is_valid).

However, for some table sizes, the code in dm_table_find_target() that
performs btree lookup will access out of bound memory structures.

Fix this bug by testing the sector number at the beginning of
dm_table_find_target(). Also, add an "inline" keyword to the function
dm_table_get_size() because this is a hot path.

Fixes: 512875bd ("dm: table detect io beyond device")
Cc: stable@vger.kernel.org
Reported-by: Zhang Tao <kontais@zoho.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

In commit 6096d91a ("dm space map metadata: fix occasional leak
of a metadata block on resize"), we refactor the commit logic to a new
function 'apply_bops'.  But when that logic was replaced in out() the
return value was not stored.  This may lead out() returning a wrong
value to the caller.

Fixes: 6096d91a ("dm space map metadata: fix occasional leak of a metadata block on resize")
Cc: stable@vger.kernel.org
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

When btree_split_beneath() splits a node to two new children, it will
allocate two blocks: left and right.  If right block's allocation
failed, the left block will be unlocked and marked dirty.  If this
happened, the left block'ss content is zero, because it wasn't
initialized with the btree struct before the attempot to allocate the
right block.  Upon return, when flushing the left block to disk, the
validator will fail when check this block.  Then a BUG_ON is raised.

Fix this by completely initializing the left block before allocating and
initializing the right block.

Fixes: 4dcb8b57 ("dm btree: fix leak of bufio-backed block in btree_split_beneath error path")
Cc: stable@vger.kernel.org
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

If rs_prepare_reshape() fails, no cleanup is executed, leading to
leak of the raid_set structure allocated at the beginning of
raid_ctr(). To fix this issue, go to the label 'bad' if the error
occurs.

Fixes: 11e47232 ("dm raid: stop keeping raid set frozen altogether")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This function is supposed to return error pointers so it matches the
dmz_get_rnd_zone_for_reclaim() function.  The current code could lead to
a NULL dereference in dmz_do_reclaim()

Fixes: b234c6d7 ("dm zoned: improve error handling in reclaim")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Change the "frontend" dust_remove_block, dust_add_block, and
dust_query_block functions to store the "dust block number", instead
of the sector number corresponding to the "dust block number".

For the "backend" functions dust_map_read and dust_map_write,
right-shift by sect_per_block_shift.  This fixes the inability to
emulate failure beyond the first sector of each "dust block" (for
devices with a "dust block size" larger than 512 bytes).

Fixes: e4f3fabd ("dm: add dust target")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan Gurney <bgurney@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Fix a crash that was introduced by the commit 724376a0. The crash is
reported here: https://gitlab.com/cryptsetup/cryptsetup/issues/468

When reading from the integrity device, the function
dm_integrity_map_continue calls find_journal_node to find out if the
location to read is present in the journal. Then, it calculates how many
sectors are consecutively stored in the journal. Then, it locks the range
with add_new_range and wait_and_add_new_range.

The problem is that during wait_and_add_new_range, we hold no locks (we
don't hold ic->endio_wait.lock and we don't hold a range lock), so the
journal may change arbitrarily while wait_and_add_new_range sleeps.

The code then goes to __journal_read_write and hits
BUG_ON(journal_entry_get_sector(je) != logical_sector); because the
journal has changed.

In order to fix this bug, we need to re-check the journal location after
wait_and_add_new_range. We restrict the length to one block in order to
not complicate the code too much.

Fixes: 724376a0 ("dm integrity: implement fair range locks")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

dm-zoned is observed to lock up or livelock in case of hardware
failure or some misconfiguration of the backing zoned device.

This patch adds a new dm-zoned target function that checks the status of
the backing device. If the request queue of the backing device is found
to be in dying state or the SCSI backing device enters offline state,
the health check code sets a dm-zoned target flag prompting all further
incoming I/O to be rejected. In order to detect backing device failures
timely, this new function is called in the request mapping path, at the
beginning of every reclaim run and before performing any metadata I/O.

The proper way out of this situation is to do

dmsetup remove <dm-zoned target>

and recreate the target when the problem with the backing device
is resolved.

Fixes: 3b1a94c8 ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Some errors are ignored in the I/O path during queueing chunks
for processing by chunk works. Since at least these errors are
transient in nature, it should be possible to retry the failed
incoming commands.

The fix -

Errors that can happen while queueing chunks are carried upwards
to the main mapping function and it now returns DM_MAPIO_REQUEUE
for any incoming requests that can not be properly queued.

Error logging/debug messages are added where needed.

Fixes: 3b1a94c8 ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

There are several places in reclaim code where errors are not
propagated to the main function, dmz_reclaim(). This function
is responsible for unlocking zones that might be still locked
at the end of any failed reclaim iterations. As the result,
some device zones may be left permanently locked for reclaim,
degrading target's capability to reclaim zones.

This patch fixes these issues as follows -

Make sure that dmz_reclaim_buf(), dmz_reclaim_seq_data() and
dmz_reclaim_rnd_data() return error codes to the caller.

dmz_reclaim() function is renamed to dmz_do_reclaim() to avoid
clashing with "struct dmz_reclaim" and is modified to return the
error to the caller.

dmz_get_zone_for_reclaim() now returns an error instead of NULL
pointer and reclaim code checks for that error.

Error logging/debug messages are added where necessary.

Fixes: 3b1a94c8 ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This patch fixes a problem in dm-kcopyd that may leave jobs in
complete queue indefinitely in the event of backing storage failure.

This behavior has been observed while running 100% write file fio
workload against an XFS volume created on top of a dm-zoned target
device. If the underlying storage of dm-zoned goes to offline state
under I/O, kcopyd sometimes never issues the end copy callback and
dm-zoned reclaim work hangs indefinitely waiting for that completion.

This behavior was traced down to the error handling code in
process_jobs() function that places the failed job to complete_jobs
queue, but doesn't wake up the job handler. In case of backing device
failure, all outstanding jobs may end up going to complete_jobs queue
via this code path and then stay there forever because there are no
more successful I/O jobs to wake up the job handler.

This patch adds a wake() call to always wake up kcopyd job wait queue
for all I/O jobs that fail before dm_io() gets called for that job.

The patch also sets the write error status in all sub jobs that are
failed because their master job has failed.

Fixes: b73c67c2 ("dm kcopyd: add sequential write feature")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Revert the commit bd293d07. The proper
fix has been made available with commit d0a255e7 ("loop: set
PF_MEMALLOC_NOIO for the worker thread").

Note that the fix offered by commit bd293d07 doesn't really prevent
the deadlock from occuring - if we look at the stacktrace reported by
Junxiao Bi, we see that it hangs in bit_wait_io and not on the mutex -
i.e. it has already successfully taken the mutex. Changing the mutex
from mutex_lock to mutex_trylock won't help with deadlocks that happen
afterwards.

PID: 474    TASK: ffff8813e11f4600  CPU: 10  COMMAND: "kswapd0"
   #0 [ffff8813dedfb938] __schedule at ffffffff8173f405
   #1 [ffff8813dedfb990] schedule at ffffffff8173fa27
   #2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec
   #3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186
   #4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f
   #5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8
   #6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81
   #7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio]
   #8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio]
   #9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio]
  #10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce
  #11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778
  #12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f
  #13 [ffff8813dedfbec0] kthread at ffffffff810a8428
  #14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd293d07 ("dm bufio: fix deadlock with loop device")
Depends-on: d0a255e7 ("loop: set PF_MEMALLOC_NOIO for the worker thread")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Pull dax fixes from Dan Williams:
 "A filesystem-dax and device-dax fix for v5.3.

  The filesystem-dax fix is tagged for stable as the implementation has
  been mistakenly throwing away all cow pages on any truncate or hole
  punch operation as part of the solution to coordinate device-dma vs
  truncate to dax pages.

  The device-dax change fixes up a regression this cycle from the
  introduction of a common 'internal per-cpu-ref' implementation.

  Summary:

   - Fix dax_layout_busy_page() to not discard private cow pages of
     fs/dax private mappings.

   - Update the memremap_pages core to properly cleanup on behalf of
     internal reference-count users like device-dax"

* tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  mm/memremap: Fix reuse of pgmap instances with internal references
  dax: dax_layout_busy_page() should not unmap cow pages

Pull NTB fix from Jon Mason:
 "Bug fix for NTB MSI kernel compile warning"

* tag 'ntb-5.3-bugfixes' of git://github.com/jonmason/ntb:
  NTB/msi: remove incorrect MODULE defines

Pull RISC-V updates from Paul Walmsley:
 "A few minor RISC-V updates for v5.3-rc4:

   - Remove __udivdi3() from the 32-bit Linux port, converting the only
     upstream user to use do_div(), per Linux policy

   - Convert the RISC-V standard clocksource away from per-cpu data
     structures, since only one is used by Linux, even on a multi-CPU
     system

   - A set of DT binding updates that remove an obsolete text binding in
     favor of a YAML binding, fix a bogus compatible string in the
     schema (thus fixing a "make dtbs_check" warning), and clarifies the
     future values expected in one of the RISC-V CPU properties"

* tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  dt-bindings: riscv: fix the schema compatible string for the HiFive Unleashed board
  dt-bindings: riscv: remove obsolete cpus.txt
  RISC-V: Remove udivdi3
  riscv: delay: use do_div() instead of __udivdi3()
  dt-bindings: Update the riscv,isa string description
  RISC-V: Remove per cpu clocksource

Pull x86 fixes from Thomas Gleixner:
 "A few fixes for x86:

   - Don't reset the carefully adjusted build flags for the purgatory
     and remove the unwanted flags instead. The 'reset all' approach led
     to build fails under certain circumstances.

   - Unbreak CLANG build of the purgatory by avoiding the builtin
     memcpy/memset implementations.

   - Address missing prototype warnings by including the proper header

   - Fix yet more fall-through issues"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/lib/cpu: Address missing prototypes warning
  x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS
  x86/purgatory: Do not use __builtin_memcpy and __builtin_memset
  x86: mtrr: cyrix: Mark expected switch fall-through
  x86/ptrace: Mark expected switch fall-through

Pull perf tooling fixes from Thomas Gleixner:
 "Perf tooling fixes all over the place:

   - Fix the selection of the main thread COMM in db-export

   - Fix the disassemmbly display for BPF in annotate

   - Fix cpumap mask setup in perf ftrace when only one CPU is present

   - Add the missing 'cpu_clk_unhalted.core' event

   - Fix CPU 0 bindings in NUMA benchmarks

   - Fix the module size calculations for s390

   - Handle the gap between kernel end and module start on s390
     correctly

   - Build and typo fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf pmu-events: Fix missing "cpu_clk_unhalted.core" event
  perf annotate: Fix s390 gap between kernel end and module start
  perf record: Fix module size on s390
  perf tools: Fix include paths in ui directory
  perf tools: Fix a typo in a variable name in the Documentation Makefile
  perf cpumap: Fix writing to illegal memory in handling cpumap mask
  perf ftrace: Fix failure to set cpumask when only one cpu is present
  perf db-export: Fix thread__exec_comm()
  perf annotate: Fix printing of unaugmented disassembled instructions from BPF
  perf bench numa: Fix cpu0 binding

Pull scheduler fixes from Thomas Gleixner:
 "Three fixlets for the scheduler:

   - Avoid double bandwidth accounting in the push & pull code

   - Use a sane FIFO priority for the Pressure Stall Information (PSI)
     thread.

   - Avoid permission checks when setting the scheduler params for the
     PSI thread"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/psi: Do not require setsched permission from the trigger creator
  sched/psi: Reduce psimon FIFO priority
  sched/deadline: Fix double accounting of rq/running bw in push & pull

Pull irq fix from Thomas Gleixner:
 "A small fix for the affinity spreading code.

  It failed to handle situations where a single vector was requested
  either due to only one CPU being available or vector exhaustion
  causing only a single interrupt to be granted.

  The fix is to simply remove the requirement in the affinity spreading
  code for more than one interrupt being available"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Create affinity mask for single vector

Pull objtool warning fix from Thomas Gleixner:
 "The recent objtool fixes/enhancements unearthed a unbalanced CLAC in
  the i915 driver.

  Chris asked me to pick the fix up and route it through"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  drm/i915: Remove redundant user_access_end() from __copy_from_user() error path

Pull gfs2 fix from Andreas Gruenbacher:
 "Fix incorrect lseek / fiemap results"

* tag 'gfs2-v5.3-rc3.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: gfs2_walk_metadata fix

A compilation -Wimplicit-fallthrough warning was enabled by commit
a035d552 ("Makefile: Globally enable fall-through warning")

Even though clang 10.0.0 does not currently support this warning without
a patch, clang currently does not support a value for this option.

  Link: https://bugs.llvm.org/show_bug.cgi?id=39382

The gcc default for this warning is 3 so removing the =3 has no effect
for gcc and enables the warning for patched versions of clang.

Also remove the =3 from an existing use in a parisc Makefile:
arch/parisc/math-emu/Makefile
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-and-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull char/misc driver fixes Greg KH:
 "Here are some small char/misc driver fixes for 5.3-rc4.

  Two of these are for the habanalabs driver for issues found when
  running on a big-endian system (are they still alive?) The others are
  tiny fixes reported by people, and a MAINTAINERS update about the
  location of the fpga development tree.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: Fix DEBUG_LOCKS_WARN_ON for uninitialized attribute
  MAINTAINERS: Move linux-fpga tree to new location
  nvmem: Use the same permissions for eeprom as for nvmem
  habanalabs: fix host memory polling in BE architecture
  habanalabs: fix F/W download in BE architecture