Online setting of a qeth device may fail for instance because of:
- out-of-memory condition when allocating qdio queues
- IDX ACTIVATE problem
- ...
Such a device is still returned in a driver_for_each_device loop
processed in qeth_reboot_event(), which calls
qeth_clear_qdio_buffers(). Make sure qeth_clear_output_buffer() is
called only, if the qdio queues have been successfully allocated
during initialization of a qeth device.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

TSO requires tx checksumming. For non GSO frames in TSO/EDDP mode we
have to manually calculate the checksum.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

under memory pressure scatter gather mode switching messages must be
rate limited.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Problem:
A recovery thread must not be active when device is removed.
In qeth_remove_device() an interruptible wait operation is used
to wait until a qeth recovery thread is finished. If a user really
interrupts the ungroup operation of a qeth device while a recovery
is running, cio and qeth are out of sync (device already removed
from cio, but kept in qeth). A following module unload of qeth
results in a kernel OOPS here.

Solution:
Do not allow interruption of ungroup operation to guarantee
finishing of a potentially running qeth recovery thread.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot.  This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register.  This happens
to work for the console but not rarely for additional ports.

While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

acpi_get_devices() returns success if it did not find any device.
We have to check for this case.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Daniel Ritz <daniel.ritz-ml@swissonline.ch>
Tested-by: Luca <kronos.it@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  SELinux: clear parent death signal on SID transitions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - make dummy touchkit_ps2_detect() static
  Input: gscps2 - convert to use kzalloc
  Input: iforce - fix 'unused variable' warning
  Input: i8042 - fix retrun value of i8042_aux_test_irq
  Input: gpio_keys - remove duplicate includes

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4561/1: i.MX/MX1 GPIO parenthes omission and input setup fix
  [ARM] 4557/1: Fix PXA irq gpio initialization
  [ARM] 4551/1: s3c24xx: fix wrong virtual address offsets
  [ARM] 4552/1: i.MX/MX1 GPIO output setup fix
  [ARM] 4553/1: ARM at91: define FIQ_START
  [ARM] 4554/1: replace consistent_sync() with flush_ioremap_region()
  ARM: OMAP: Enable serial idling and wakeup features
  ARM: OMAP2: Force APLLs always active
  ARM: OMAP: H3 workqueue fixes
  ARM: OMAP: OSK led fixes
  ARM: OMAP: fix OMAP1 dmtimer build warning
  ARM: OMAP: Fix 32k timer unsupported one-shot mode

Alexey Dobriyan reports that maxcpus=1 is still broken in 2.6.23-rc4:
if CONFIG_HOTPLUG_CPU is not set, x86_64 bootup oopses in show_stat() -
for_each_possible_cpu accesses a per-cpu area which was never set up.

Alexey identified commit 61ec7567
(ACPI: boot correctly with "nosmp" or "maxcpus=0") as the origin;
but it's not really to blame, just exposes a bug in 2.6.23-rc1's commit
8b3b2955 (Especially when !CONFIG_HOTPLUG_CPU,
avoid needlessy allocating resources for CPUs that can never become available).

rc1's test for max_cpus < 2 in start_kernel() wasn't working because
max_cpus was still NR_CPUS at that point: until rc4 moved the maxcpus
parsing earlier.  Now it sets cpu_possible_map to 1 before allocating
all possible per-cpu areas; then smp_init() expands cpu_possible_map
to cpu_present_map (0xf in my case) later on.

rc1's commit has good intentions, but expects cpu_present_map to be
limited by maxcpus, which is only the case on i386.  cpus_and(possible,
possible,present) might be good, but needs an audit of cpu_present_map
uses - there may well be assumptions that any cpu present is possible.

So stay safe for now and just revert those #ifndef CONFIG_HOTPLUG_CPU
optimizations in rc1's commit.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Clear parent death signal on SID transitions to prevent unauthorized
signaling between SIDs.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Eric Paris <eparis@parisplace.org>
Signed-off-by: James Morris <jmorris@localhost.localdomain>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] PS3: Fix bug where the major version part is not compared
  [POWERPC] Update defconfigs
  [POWERPC] spufs: Don't call spu_run_init from spu_reacquire_runnable
  [POWERPC] spufs: Fix update of mailbox status register during backed wbox write
  [POWERPC] spu_manage: fix spu_unit_number for celleb device tree
  [POWERPC] Update defconfigs
  [POWERPC] Flush registers to proper task context

Another fallout from the removal of #include <linux/fs.h> from mm.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If the stack pointer is 0xc057a000, then the first stack page is at
0xc0579000 (the stack pointer is decremented before use).  Not
calculating this correctly caused guests with CONFIG_DEBUG_PAGEALLOC=y
to be killed with a "bad stack page" message: the initial kernel stack
was just proceeding the .smp_locks section which
CONFIG_DEBUG_PAGEALLOC marks read-only when freeing.

Thanks to Frederik Deweerdt for the bug report!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the bug that the major version part of the firmware version number
is ignored in the comparison done by ps3_compare_firmware_version
because the difference of two 64-bit quantities is returned as an int.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

During GPIO testing on PiMX1 board there has been revealed
problem with some pins input functions. The GIUS bit has
to be set for inputs to work reliably too. It is surprising
that input worked on some inputs with incorrect setup before.
DR is not mandatory, but it ensures stable constant level
on internal traces.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Paul Mackerras <paulus@samba.org>

This fixes a major bug which was happening when a SPU thread advances
its execution right after being restored to a SPU.  A potentially
outdated NPC value was being (re)written to the SPU.

So, spu_run_init, in this case, was either not doing anything relevant,
or breaking the execution of the SPU thread.

This fixes a common problem of losing a mailbox write when it was done
to a saved context.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When a process writes into the inbound spu mailbox (wbox) while the
context is saved, we accidentally break the contents of the mb_stat_R
register by clearing other entries of the mailbox status register. This
can cause the user side to hang.

This change fixes the problem by only altering the appropriate bits
of the mailbox status register during a backing-store write.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The dummy touchkit_ps2_detect() for the CONFIG_MOUSE_PS2_TOUCHKIT=n case
shouldn't be a global function.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

drivers/input/joystick/iforce/iforce-packets.c: In function `iforce_get_id_packet':
drivers/input/joystick/iforce/iforce-packets.c:249: warning: unused variable `status'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

We should not return IRQ_HANDLED if we didn't handle the interrupt.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This fixes a regression introduced with 2.6.23-rc4 after on some
confusion about the device tree interfaces.

IBM QS21 device trees provide "physical-id", so we changed the code to
run on that and remain compatible with all IBM machines.

However, the Toshiba Celleb device tree provides the "unit-id" property,
which was in the Linux code, but never used in this way on IBM hardware.

Legacy device tree used the reg property for the physical id of an spe.
This patch fixes find_spu_unit_number to look for the spu id in that order.
The length is checked to avoid misinterpretation in case the attributes
unit-id or reg do not contain the id.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Jeremy Kerr <jk@ozlabs.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

When we flush register state for FP, Altivec, or SPE in flush_*_to_thread
we need to respect the task_struct that the caller has passed to us.

Most cases we are called with current, however sometimes (ptrace) we may
be passed a different task_struct.

This showed up when using gdbserver debugging a simple program that used
floating point. When gdb tried to show the FP regs they all showed up as
0, because the child's FP registers were never properly flushed to memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

As pointed out by Jrgen, we are overflowing the number of GPIOs
in pxa_init_irq_gpio(). I'm seeing the same problem on my HTC
Universal PXA270 based PDA.
According to Eric, the function argument is the number of GPIOs,
so we should keep the semantics and reduce the number of
iteration by 1.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Jrgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Without this, we get qla2xxx complaining about "ISP System Error".

What's happening here is the firmware is detecting a Xfer-ready from the
storage when in fact the data-direction for a mode-select should be a
write (DATA_OUT).

The following patch fixes the problem (typo). Verified by Brian, as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Verified-by: Brian De Wolf <bldewolf@csupomona.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC32]: Make flush_tlb_kernel_range() an inline function.
  [SERIAL]: Fix 32-bit warnings in sunzilog.c and sunsu.c
  [SPARC32]: Kill unused vars and macros from prom/console.c
  [SPARC32]: Add __cmpdi2() libcall implementation ala. MIPS.
  [VIDEO]: Do not prom_halt() in cg3 and bw2 device probe.
  [SUNVDC]: Use slice 0xff on VD_DISK_TYPE_DISK.

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Mark Paul Moore as maintainer of labelled networking.
  [VLAN/BRIDGE]: Fix "skb_pull_rcsum - Fatal exception in interrupt"
  [ISDN]: Get rid of some pointless allocation casts in common and bsd comp.
  [NET]: Avoid pointless allocation casts in BSD compression module
  [IRDA]: Do not do pointless kmalloc return value cast in KingSun driver
  [NET]: Fix crash in dev_mc_sync()/dev_mc_unsync()
  [PPPOL2TP]: Fix endianness annotations.
  [IOAT]: ioatdma needs to to play nice in a multi-dma-client world
  [SLIP]: trivial sparse warning fix
  [EQL]: sparse warning fix
  [NET]: is_power_of_2 in net/core/neighbour.c
  [TCP]: Describe tcp_init_cwnd() thoroughly in a comment.
  [NET]: Fix IP_ADD/DROP_MEMBERSHIP to handle only connectionless
  [KBUILD]: Sanitize tc_ematch headers.
  [IPSEC] AH4: Update IPv4 options handling to conform to RFC 4302.

Fix bogus DEBUG_PREEMPT warning on x86_64, when cpu brought online after
bootup: current_is_keventd is right to note its use of smp_processor_id
is preempt-safe, but should use raw_smp_processor_id to avoid the warning.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sigh.  Again an ACPI assault on the Thinkpad's Fn+F4 to suspend to RAM.
The default and text for CONFIG_THINKPAD_ACPI_INPUT_ENABLED were fixed
in -rc3, but now commit 14e04fb3 ("ACPI:
Schedule /proc/acpi/event for removal") introduces the ACPI_PROC_EVENT
config entry, and defaults it to 'n' to disable it again.

Change default to y, and add comment to make it clearer that n is for
future distros.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 61ec7567 ('ACPI: boot correctly
with "nosmp" or "maxcpus=0"') broke 'maxcpus=' handling on x86[-64].

maxcpus=N is now having no effect on x86_64, and freezing bootup on i386
(because of inconsistency with the separate maxcpus parsing down in
arch/i386, I guess).  That's because early_param parsing is a little
different from __setup parsing, and needs the "=" omitted: then it seems
to work as the original commit intended (no mention of IO-APIC in
/proc/interrupts when maxcpus=0).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (60 commits)
  [MIPS] Fulong doesn't need ISA DMA.
  [MIPS] IP27: intr_sconnect_level: don't disable interrupts.
  [MIPS] IP27: startup_bridge_irq: connect interrupt.
  [MIPS] IP27: shutdown_bridge_irq: don't free irq.
  [MIPS] Sort out handling of ISA-less PCI systems.
  [MIPS] Add __cmpdi2
  [MIPS] HOTPLUG: Make register_pci_controller __devinit.
  [MIPS] PCI: Remove __devinit attribute from pcibios_fixup_bus.
  [MIPS] PCI: Remove __devinit attribute from pcibios_fixup_bus.
  [MIPS] Delete duplicate inclusion of <linux/delay.h>.
  [MIPS] Polish <asm/edac.h>.
  [MIPS] IP22: Export sgi_gfxaddr for use by the Newport console driver.
  [MIPS] Maintain si_code field properly for FP exceptions
  [MIPS] SMTC: Fix duplicate status dumps on NMI
  [MIPS] Unconditionally writeback and invalidate caches on kexec.
  [PATCH] rtc: Make rtc-rs5c348 driver hotplug-aware
  [MIPS] Fix gcc 3.3 warning.
  [MIPS] Fix invalid semicolon after if statement
  [MIPS] Update Cobalt defconfig
  [MIPS] Update workpad_defconfig
  ...

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fix SLB initialization at boot time
  [POWERPC] Fix undefined reference to device_power_up/resume
  [POWERPC] cell: Update cell_defconfig for 2.6.23
  [POWERPC] axonram: Do not delete gendisks queue in error path
  [POWERPC] axonram: Module modification for latest firmware API changes
  [POWERPC] cell: Support pinhole-reset on IBM cell blades
  [POWERPC] spu_manage: Use newer physical-id attribute
  [POWERPC] pasemi: Another IOMMU bugfix for 64K PAGE_SIZE