- 15 Aug, 2019 40 commits
-
-
Michael Strauss authored
[Why] DCN10 performs color processing before MPC combination, causes color shift in RGB colorspaces when positive brightness offset is applied However, YCbCr is still unfixed and remains disabled [How] Add layerIndex to dc_plane_state and dc_plane_info structs Re-enable MPO when brightness is adjusted and colorspace is not YCbCr Set rear plane's brightness offset to 0 when front plane visible Signed-off-by:
Michael Strauss <michael.strauss@amd.com> Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Acked-by:
Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
yanyan kang authored
[why] disable_az_endpoint has been skipped because dc->debug.az_endpoint_mute_only = true. [how] set dc->debug.az_endpoint_mute_only false when PPLIB’s PME notification function pointer is not NULL at the dcn10_resource construct function,because right now SMU/PPLIB and DAL all have the AZ D3 force PME notification implemented. AZ D3 should work. Signed-off-by:
yanyan kang <Yanyan.Kang@amd.com> Reviewed-by:
Charlene Liu <Charlene.Liu@amd.com> Acked-by:
-
Wenjing Liu authored
[why] During detection link training if a display is disconnected, the current code will retry 3 times of link training on disconnected link before giving up. [how] Before each retry check for HPD status, only retry verify link cap when HPD is still high. Also put a 10ms delay between each retry to improve the chance of success. Signed-off-by:
Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by:
-
Charlene Liu authored
Enable dcn_mem_pwr as golden setting updates Signed-off-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
-
Anthony Koo authored
Signed-off-by:
-
Dmytro Laktyushkin authored
Currently the paremeters are extracted as if dml is calculating using pipes as we pass them in. in reality, dml internally merges pipes into planes if pipe split is detected. This change adds reverse logic to dcn20_calculate_dlg_params so that the global sync parameters can be correctly extracted for all the pipes when pipe split is enabled. Signed-off-by:
-
Anthony Koo authored
Signed-off-by:
-
Nikola Cornij authored
[why] Some logs messages were not precise and some new log messages were needed after "get packed PPS" function was introduced Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
-
Wyatt Wood authored
[Why] A recent bug showed that logging would be useful in debugging various gamma issues. [How] Add logging in dc. Signed-off-by:
Wyatt Wood <wyatt.wood@amd.com> Reviewed-by:
Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by:
-
Julian Parkin authored
There are repeated (but guarded) definitions of dwb_src enums. There are also unused entires. Clean them up. Signed-off-by:
Julian Parkin <julian.parkin@amd.com> Reviewed-by:
-
Qingqing Zhuo authored
Add h_timing_div_mode enum to better reflect possible register values. Replace previously programmed values with enum Signed-off-by:
Qingqing Zhuo <qingqing.zhuo@amd.com> Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] These are needed to send back DRM vblank events in the case where VRR is on. Without the interrupt enabled we're deferring the events into the vblank queue and userspace is left waiting forever to get back the events they need. Found using igt@kms_vrr - the test fails immediately due to vblank timeout. [How] Register them the same way we're handling it for DCN1. This fixes igt@kms_vrr for DCN2. Signed-off-by:
David Francis <David.Francis@amd.com> Acked-by:
-
Charlene Liu authored
[Description] OGAM_MEM_PWR could stay in light up when driver woke up to update gamma. either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away. Easy reproduce after LOW_MEM Power feature enables and resume from S3. Signed-off-by:
Julian Parkin <jparkin@amd.com> Acked-by:
-
Nikola Cornij authored
[why] A misleading message "Programming PPS" appears before both programming and "query PPS" functions [how] Move the message from "log PPS" function to "program PPS" function Signed-off-by:
-
Vitaly Prosyak authored
Not all ASIC types have this function implemented - check before calling. Signed-off-by:
Vitaly Prosyak <vitaly.prosyak@amd.com> Reviewed-by:
-
Ilya Bakoulin authored
The type was changed previously to better reflect possible register values. Signed-off-by:
Ilya Bakoulin <Ilya.Bakoulin@amd.com> Reviewed-by:
-
Wyatt Wood authored
[Why] A recent bug showed that logging would be useful in debugging various gamma issues. [How] Add new log types and logging code to the color module. Signed-off-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Nikola Cornij authored
[why] If DSC is available, a higher picture quality is achieved by using DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit and would only introduce loss of quality. Removing it reduces maintenance and testing effort. Signed-off-by:
-
Lewis Huang authored
[Why] The vm config will be clear to 0 when system enter S4. It will cause hubbub didn't know how to fetch data when system resume. The flip always pending because earliest_inuse_address and request_address are different. [How] Reprogram VM config when system resume Signed-off-by:
Lewis Huang <Lewis.Huang@amd.com> Reviewed-by:
Eric Yang <eric.yang2@amd.com> Acked-by:
-
Eric Yang authored
[Why and How] We want to change where timing is done for alt mode. Some of the commented out #ifs are needed for DCN20 so we enable them for that case. Signed-off-by:
-
Ilya Bakoulin authored
[Why] - Need to change interface function signature / add an enum to reflect the available register field values [How] - Add a new enum and modify existing functions to use it instead of bool Signed-off-by:
-
Dmytro Laktyushkin authored
Current optc odm interface only accepts 2 opps, we need to expand this to allow 4 to 1 odm combine. Signed-off-by:
-
Ilya Bakoulin authored
[Why] Need to add DML struct members that were omitted in previous DML implemenations. [How] - Add missing enum values - Add missing struct members - Set new input values in the fetch functions Signed-off-by:
-
Julian Parkin authored
[Why] There are currently two interfaces for exactly the same thing: hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub version is currently unused past dcn10, largely because the call from the dcn10 hardware sequencer does not call through the interface, so the hupb interface was used instead. This is confusing because of the duplicate code, the unused functions, and the fact that more that one block currently owns this set of registers. [How] Remove the hubp interface entirely, as well as the register declarations that are not longer needed because of this. Change the call site to always call the hubbub version through the interface. Fix the update_dchub function in dcn20_hubbub.c to program the correct registers for dcn20. Signed-off-by:
-
Jun Lei authored
[why] Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full update is performed, the HWSS will only update the MPCC tree for the stream that is updated as opposed to all streams. This means that when mapping pipes in validation, care must be taken to not change any existing mapping, otherwise it leads to partial hw programming [how] it's not strictly necessary to track which stream/mpcc tree is being updated, but rather it's sufficient to compare current and new state and just keep pipes that were previously already mapped unchanged. Signed-off-by:
-
Aric Cyr authored
Signed-off-by:
-
Nikola Cornij authored
[why] At the time DIG FE is connected to its BE, the clocks in OTG are enabled and PHY will also be set up. When DSC has to be used to fit the stream into the available bandwidth, without DSC being set DIG could get exposed to the higer bandwidth it (or link) could handle. This causes the HW to "reject" video enable setup (the register shows that video enable was attempted, but the status bit shows it as disabled). [how] - Separate DSC setup into DSC register config and DSC PPS SDP setup - Move most of the DSC setup (register config) to before dcn10_link_encoder_connect_dig_be_to_fe() is called - Set up DSC PPS SDP after DIG FE is connected to its BE. This is because setting DSC PPS SDP before that has no effect. Signed-off-by:
-
Nikola Cornij authored
[why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide Signed-off-by:
-
Vitaly Prosyak authored
[Why & How] Support hlg OETF and EOTF based on BT.2100-2 Follow up is required. Signed-off-by:
-
Jun Lei authored
[why] Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since DMLv2 has gone through proper validation. v2 can now be used as the default and 1 level of fallback can be removed [how] remove previous workaround implemenation Signed-off-by:
-
Martin Leung authored
[Why] Seamless boot (building SW state inheriting BIOS-initialized timing) was enabled on DCN2, including fixes [How] Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/ Pixel clock. This is part 2 of 2 for seamless boot NV10 Signed-off-by:
Martin Leung <martin.leung@amd.com> Reviewed-by:
-
Martin Leung authored
[Why] underflow seen on certain monitor setups caused by making dcnxx_init_hw generic [How] by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr memset in an else statement so both memsets don't get set Signed-off-by:
-
Martin Leung authored
[Why] For seamless boot the init_hw sequence must be split into actual hardware vs pipes, in order to defer pipe initialization to set mode and skip of pipe-destructive sequences [How] made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit deleted dcn20 specific versions. This is part 1 of a 2 partimplementation of seamless boot Signed-off-by:
-
Aric Cyr authored
Signed-off-by:
-
Jun Lei authored
[why] When planes are enabled, they must be enabled using VSYNC update (not immediate). However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address only. This operation would normally be okay, but if the locking for immediate flip happens to occur before the VUPDATE associated with the initial plane enablement, it will cause HW to hang. [how] HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane. Signed-off-by:
-
Su Sung Chung authored
[why] if dynamic allocation fails during gpio_open, it will cause crash due to page fault. [how] handle allocation when gpio object gets created and prevent from calling gpio_open if allocation failed Signed-off-by:
Su Sung Chung <Su.Chung@amd.com> Reviewed-by:
-
Jaehyun Chung authored
[Why] Auto Overclock Memory fails for some systems that don't support p-state. [How] Implement the workaround, and it's corresponding enable flag. Signed-off-by:
Jaehyun Chung <jaehyun.chung@amd.com> Reviewed-by:
Alvin Lee <Alvin.Lee2@amd.com> Acked-by:
-
Jun Lei authored
[why] DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not. This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need an increased divider will temporarily have actual DPP clock drop below minimum while DTO double buffering takes effect. This results in temporary underflow. [how] To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase. When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because we do not use dividers larger than 1. Signed-off-by:
-
Dmytro Laktyushkin authored
Currently every time DC wants to access firmware info we make a call into VBIOS. This makes no sense as there is nothing that can change runtime inside fw info and can cause issues when calling unstable bios during bringup. This change eliminate this behavior by only calling bios once for fw info and keeping it stored as part of dc_bios. Signed-off-by:
Chris Park <Chris.Park@amd.com> Acked-by:
-
David Galiffi authored
[WHY] We require a method to perform synchronous link training. [HOW] Sync LT is broken into 3 basic steps. "Begin" starts the state machine, and resets "preferred" link settings. "Attempt" will attempt to train the link with a given set of training parameters. "End" stops the state machine, and will optionally disable the link phy. Between "Begin" and "End" DPCD:600h must not be set to "2" (D3:Powered Down). Between "Begin" and "End", there may be multiple "Attempts" with different training parameters. Signed-off-by:
David Galiffi <david.galiffi@amd.com> Reviewed-by:
-
