Add ISP24xx diagnostic routines.

Add function and structure definitions for the ISP24xx
diagnostic firmware dump routines.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Add ISP24xx definitions.

Add requisite structure definitions and #define's for ISP24xx
support.  Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Add pci ids for new ISP types.

Move old definitions in local qla_def.h file to pci_ids.h as
well.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Factor-out ISP specific functions to method-based call tables.

In anticipation of ISP24xx/ISP25xx support, factor-out ISP
specific functions into a method-based call table.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

At the moment, the transport class blindly tries to set things like
QAS and IU, even if the drive won't support them.  It's best not to
annoy the devices like this and instead only set what the drive says
is actually supported.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

now that we do normal PCI probing there's no need to keep a list of
all HBAs.

Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

always probe in bus order, avoid any reordering
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Here's a tiny update that means we print the correct ASCII type
information
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

drivers/scsi/dpt_i2o.c: In function `adpt_queue':
drivers/scsi/dpt_i2o.c:385: warning: unused variable `timeout'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Use the macros consistently in ahd_linux_dev_reset().

If ahd_linux_dev_reset() really can be called with local interrupts disabled
then yuk.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Apparently these are the only drives that try to negotiate IU and QAS
at u160 speeds.  The aic7xxx driver can't cope with this.  The fix is
to eliminate the IU and QAS setting routines.  I've #if 0'd them out,
just in case we ever get the sequencer documentation out of Adaptec,
since we'd then be able to fix the driver.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix the problem in IBM VSCSI Client where the client doesn't send the
information which is expected by the server.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This code pokes deep into EH internals and duplicates scsi_error.c code
wrongly.  It doesn't compile anymore in scsi-misc, so let's #if 0 out
the code - the driver hasn't worked for more than five years anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Update copyright notice text and include year 2005.

Add Copyright notice for Christoph Hellwig to several files: lpfc.h
lpfc_attr.c lpfc_els.c lpfc_hbadisc.c lpfc_init.c lpfc_mbox.c
lpfc_mem.c lpfc_nportdisc.c lpfc_scsi.c lpfc_sli.c
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Symptom - An unmapped node (initiator) that goes away in a situation
such as cable pull, comes back as a mapped node.  Fix - On ADISC
completion, put a list on the mapped list only if it is a FCP_TARGET.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Add completion handler to the abort iocbs to close a hole where we
could reuse an iotag.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

lpfc_els_unsol_event() checks rjt_err to determine is LS_RJT should be
sent.  However, rjt_err was set to LSEXP_NOTHING_ELSE (which is 0) in
cases where an LS_RJT should be sent, so rjt_err was never true.
Change lpfc_els_unsol_event() to set rjt_err to 1 when LS_RJT should
be sent.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix driver not seeing LP6000.  Fix: add PCI id to the pci_device_id
table and a short description for the HBA in get_hba_model_desc().
Also add a default clause to the switch statement that parses the
various PCI ID's.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Add max_sectors to the driver host template and initialize it with
0xFFFF since the driver has no limitations on the size a transfer
contained by a scsi command and that fits within the sg_tablesize
provisioned by the driver.  This fixes a performance issue seen in
some configurations.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Bug reported via SourceForge - lpfc does not load on sparc.  The lpfc
driver must byteswap all FCP IOCBs to recover the data into cpu native
format.

Also correct issue of "iotag not found" messages
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Analysis:

Timeout of READ_SPARM64 causes call to lpfc_mbox_timeout_handler which
reads psli->mbox_active to determine the timeout mbox.  Timeout
handler then NULL's psli->mbox_active and calls
lpfc_mbx_cmpl_read_sparam(), which on timeout condition, calls
link_down().  link_down() now calls disc_done() which calls
mbox_timeout_hander() again since WORKER_MBOX_TMO is still set, which
goes back to read psli->mbox_active which is already NULL'ed.

Remove redundant if statement in lpfc_mbox_timeout_handler.  pmbox is
assigned psli->mbox_active so there is no need to check if it actually
equals psli->mbox_active.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix issue where all hosts connected to SAN get spammed with nodev
message when other initiators go away.  Display nodev message only
when FC targets go away.  However this behavior will be overridden if
LOG_DISCOVERY is set.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

From: Christoph Hellwig <hch@lst.de>:

 - rename PGP/HPH to lpfc_pgp/lpfc_hgp
 - use __le32 types for the members to start fixing sparse -Wbitwise
   issues
 - remove lpfc_sli.MBhostaddr, we can always use the pointer from
   SLI2_DESC directly
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Convert driver to use new change_queue_depth API.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>

Fixed up rejections and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

From: 	Andy Whitcroft <apw@shadowen.org>

Updated to remove the bogus translated target check.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Just opencoded access to eh_eflags, it's much more readable anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

We never look at it except for the old megaraid driver that abuses it
for sending internal commands.  That usage can be fixed easily because
those internal commands are single-threaded by a mutex and we can easily
use a completion there.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

never checked anywhere
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Never used for anything but printing it out in debug routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

it's never set to anything, and just three broken drivers are looking
at it and doing odd things.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

From: Christoph Hellwig <hch@lst.de>

Patch fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch add the following products to the driver:
        IBM ServeRAID 8i
        ICP 9014R0
        ICP 9024R0
        ICP 9047MA
        ICP 9087MA
        ICP 9085LI
        ICP 5085AU
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.

note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Use ssleep() instead of schedule_timeout to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The parentheses were missing. Noted by Pavel Machek.

1. Establish a simple API for process freezing defined in linux/include/sched.h:

   frozen(process)		Check for frozen process
   freezing(process)		Check if a process is being frozen
   freeze(process)		Tell a process to freeze (go to refrigerator)
   thaw_process(process)	Restart process
   frozen_process(process)	Process is frozen now

2. Remove all references to PF_FREEZE and PF_FROZEN from all
   kernel sources except sched.h

3. Fix numerous locations where try_to_freeze is manually done by a driver

4. Remove the argument that is no longer necessary from two function calls.

5. Some whitespace cleanup

6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
   cleared before setting PF_FROZEN, recalc_sigpending does not check
   PF_FROZEN).

This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>