Split the null_blk device driver, such that it can prepare for
zoned block interface support.
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

With gcc 4.9.0 and 7.3.0:

    block/blk-core.c: In function 'blk_pm_allow_request':
    block/blk-core.c:2747:2: warning: enumeration value 'RPM_ACTIVE' not handled in switch [-Wswitch]
      switch (rq->q->rpm_status) {
      ^

Convert the return statement below the switch() block into a default
case to fix this.

Fixes: e4f36b24 ("block: fix peeking requests during PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If __blkdev_issue_discard is in progress and a device mapper device is
reloaded with a table that doesn't support discard,
q->limits.max_discard_sectors is set to zero. This results in infinite
loop in __blkdev_issue_discard.

This patch checks if max_discard_sectors is zero and aborts with
-EOPNOTSUPP.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Zdenek Kabelac <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The flag GFP_ATOMIC already contains __GFP_HIGH. There is no need to
explicitly or __GFP_HIGH again. So, just remove unnecessary __GFP_HIGH.
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Currently mbps knob could only be set once before switching power knob to
on, after power knob has been set at least once, there is no way to set
mbps knob again due to -EBUSY.

As nullb is mainly used for testing, in order to make it flexible, this
removes the flag NULLB_DEV_FL_CONFIGURED so that mbps knob can be reset
when power knob is off, e.g.

echo 0 > /config/nullb/a/power
echo 40 > /config/nullb/a/mbps
echo 1 > /config/nullb/a/power

So does other knobs under /config/nullb/a.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We noticed in testing we'd get pretty bad latency stalls under heavy
pressure because read ahead would try to do its thing while the cgroup
was under severe pressure.  If we're under this much pressure we want to
do as little IO as possible so we can still make progress on real work
if we're a throttled cgroup, so just skip readahead if our group is
under pressure.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

A basic documentation to describe the interface, statistics, and
behavior of io.latency.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Current IO controllers for the block layer are less than ideal for our
use case.  The io.max controller is great at hard limiting, but it is
not work conserving.  This patch introduces io.latency.  You provide a
latency target for your group and we monitor the io in short windows to
make sure we are not exceeding those latency targets.  This makes use of
the rq-qos infrastructure and works much like the wbt stuff.  There are
a few differences from wbt

 - It's bio based, so the latency covers the whole block layer in addition to
   the actual io.
 - We will throttle all IO types that comes in here if we need to.
 - We use the mean latency over the 100ms window.  This is because writes can
   be particularly fast, which could give us a false sense of the impact of
   other workloads on our protected workload.
 - By default there's no throttling, we set the queue_depth to INT_MAX so that
   we can have as many outstanding bio's as we're allowed to.  Only at
   throttle time do we pay attention to the actual queue depth.
 - We backcharge cgroups for root cg issued IO and induce artificial
   delays in order to deal with cases like metadata only or swap heavy
   workloads.

In testing this has worked out relatively well.  Protected workloads
will throttle noisy workloads down to 1 io at time if they are doing
normal IO on their own, or induce up to a 1 second delay per syscall if
they are doing a lot of root issued IO (metadata/swap IO).

Our testing has revolved mostly around our production web servers where
we have hhvm (the web server application) in a protected group and
everything else in another group.  We see slightly higher requests per
second (RPS) on the test tier vs the control tier, and much more stable
RPS across all machines in the test tier vs the control tier.

Another test we run is a slow memory allocator in the unprotected group.
Before this would eventually push us into swap and cause the whole box
to die and not recover at all.  With these patches we see slight RPS
drops (usually 10-15%) before the memory consumer is properly killed and
things recover within seconds.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

wbt cares only about request completion time, but controllers may need
information that is on the bio itself, so add a done_bio callback for
rq-qos so things like blk-iolatency can use it to have the bio when it
completes.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We don't really need to save this stuff in the core block code, we can
just pass the bio back into the helpers later on to derive the same
flags and update the rq->wbt_flags appropriately.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blkcg-qos is going to do essentially what wbt does, only on a cgroup
basis.  Break out the common code that will be shared between blkcg-qos
and wbt into blk-rq-qos.* so they can both utilize the same
infrastructure.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We need to use blk_rq_stat in the blkcg qos stuff, so export some of
these helpers so they can be used by other things.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Memory allocations can induce swapping via kswapd or direct reclaim.  If
we are having IO done for us by kswapd and don't actually go into direct
reclaim we may never get scheduled for throttling.  So instead check to
see if our cgroup is congested, and if so schedule the throttling.
Before we return to user space the throttling stuff will only throttle
if we actually required it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Since IO can be issued from literally anywhere it's almost impossible to
do throttling without having some sort of adverse effect somewhere else
in the system because of locking or other dependencies.  The best way to
solve this is to do the throttling when we know we aren't holding any
other kernel resources.  Do this by tracking throttling in a per-blkg
basis, and if we require throttling flag the task that it needs to check
before it returns to user space and possibly sleep there.

This is to address the case where a process is doing work that is
generating IO that can't be throttled, whether that is directly with a
lot of REQ_META IO, or indirectly by allocating so much memory that it
is swamping the disk with REQ_SWAP.  We can't use task_add_work as we
don't want to induce a memory allocation in the IO path, so simply
saving the request queue in the task and flagging it to do the
notify_resume thing achieves the same result without the overhead of a
memory allocation.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

For backcharging we need to know who the page belongs to when swapping
it out.  We don't worry about things that do ->rw_page (zram etc) at the
moment, we're only worried about pages that actually go to a block
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Just like REQ_META, it's important to know the IO coming down is swap
in order to guard against potential IO priority inversion issues with
cgroups.  Add REQ_SWAP and use it for all swap IO, and add it to our
bio_issue_as_root_blkg helper.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-iolatency has a few stats that it would like to print out, and
instead of adding a bunch of crap to the generic code just provide a
helper so that controllers can add stuff to the stat line if they want
to.

Hide it behind a boot option since it changes the output of io.stat from
normal, and these stats are only interesting to developers.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Instead of forcing all file systems to get the right context on their
bio's, simply check for REQ_META to see if we need to issue as the root
blkg.  We don't want to force all bio's to have the root blkg associated
with them if REQ_META is set, as some controllers (blk-iolatency) need
to know who the originating cgroup is so it can backcharge them for the
work they are doing.  This helper will make sure that the controllers do
the proper thing wrt the IO priority and backcharging.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Currently io.low uses a bi_cg_private to stash its private data for the
blkg, however other blkcg policies may want to use this as well.  Since
we can get the private data out of the blkg, move this to bi_blkg in the
bio and make it generic, then we can use bio_associate_blkg() to attach
the blkg to the bio.

Theoretically we could simply replace the bi_css with this since we can
get to all the same information from the blkg, however you have to
lookup the blkg, so for example wbc_init_bio() would have to lookup and
possibly allocate the blkg for the css it was trying to attach to the
bio.  This could be problematic and result in us either not attaching
the css at all to the bio, or falling back to the root blkcg if we are
unable to allocate the corresponding blkg.

So for now do this, and in the future if possible we could just replace
the bi_css with bi_blkg and update the helpers to do the correct
translation.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

It won't be efficient to dequeue request one by one from sw queue,
but we have to do that when queue is busy for better merge performance.

This patch takes the Exponential Weighted Moving Average(EWMA) to figure
out if queue is busy, then only dequeue request one by one from sw queue
when queue is busy.

Fixes: b347689f ("blk-mq-sched: improve dispatching from sw queue")
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Reported-by: Kashyap Desai <kashyap.desai@broadcom.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Warning level 2 was used in this case: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Only attempt to merge bio iff the ctx->rq_list isn't empty, because:

1) for high-performance SSD, most of times dispatch may succeed, then
there may be nothing left in ctx->rq_list, so don't try to merge over
sw queue if it is empty, then we can save one acquiring of ctx->lock

2) we can't expect good merge performance on per-cpu sw queue, and missing
one merge on sw queue won't be a big deal since tasks can be scheduled from
one CPU to another.

Cc: Laurence Oberman <loberman@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reported-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

list_splice_tail_init() is much more faster than inserting each
request one by one, given all requets in 'list' belong to
same sw queue and ctx->lock is required to insert requests.

Cc: Laurence Oberman <loberman@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Fix typo in a function blk_mq_alloc_tag_set() comment.
if if it too large -> if it's too large.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

set->mq_map is now currently cleared if something goes wrong when
establishing a queue map in blk-mq-pci.c.  It's also cleared before
updating a queue map in blk_mq_update_queue_map().

This patch provides an API to clear set->mq_map to make it clear.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Variable n is being assigned but is never used hence it is redundant
and can be removed. Also put spacing between variables in declaration
to clean up checkpatch warnings.

Cleans up clang warning:
warning: variable 'n' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pointer dgrp is being assigned but is never used hence it is redundant
and can be removed.

Cleans up clang warning:
warning: variable 'dgrp' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pointer inode is being assigned but is never used hence it is redundant
and can be removed.

Cleans up clang warning:
warning: variable 'inode' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Variable dflags is being assigned but is never used hence it is redundant
and can be removed.

Cleans up clang warning:
warning: variable 'dflags' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Once one cgroup has io.low configured, @low_valid becomes true and other
cgroups won't switch it back whatsoever.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Since @blk_debugfs_root couldn't be configured dynamically, we can
save a few memory allocation if it's not there.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The payload of struct request is stored in the request.bio chain if
the RQF_SPECIAL_PAYLOAD flag is not set and in request.special_vec if
RQF_SPECIAL_PAYLOAD has been set. However, blk_update_request()
iterates over req->bio whether or not RQF_SPECIAL_PAYLOAD has been
set. Additionally, the RQF_SPECIAL_PAYLOAD flag is ignored by
blk_rq_bytes() which means that the value returned by that function
is incorrect if the RQF_SPECIAL_PAYLOAD flag has been set. It is not
clear to me whether this is an oversight or whether this happened on
purpose. Anyway, document that it is known that both functions ignore
RQF_SPECIAL_PAYLOAD. See also commit f9d03f96 ("block: improve
handling of the magic discard payload").
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Since __must_hold() is defined in <linux/compiler_types.h>, do not
redefine it in DRBD. Compile-tested only.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

SCSI probing may synchronously create and destroy a lot of request_queues
for non-existent devices. Any synchronize_rcu() in queue creation or
destroy path may introduce long latency during booting, see detailed
description in comment of blk_register_queue().

This patch removes one synchronize_rcu() inside blk_cleanup_queue()
for this case, commit c2856ae2(blk-mq: quiesce queue before freeing queue)
needs synchronize_rcu() for implementing blk_mq_quiesce_queue(), but
when queue isn't initialized, it isn't necessary to do that since
only pass-through requests are involved, no original issue in
scsi_execute() at all.

Without this patch and previous one, it may take more 20+ seconds for
virtio-scsi to complete disk probe. With the two patches, the time becomes
less than 100ms.

Fixes: c2856ae2 ("blk-mq: quiesce queue before freeing queue")
Reported-by: Andrew Jones <drjones@redhat.com>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We have to remove synchronize_rcu() from blk_queue_cleanup(),
otherwise long delay can be caused during lun probe. For removing
it, we have to avoid to iterate the set->tag_list in IO path, eg,
blk_mq_sched_restart().

This patch reverts 5b79413946d (Revert "blk-mq: don't handle
TAG_SHARED in restart"). Given we have fixed enough IO hang issue,
and there isn't any reason to restart all queues in one tags any more,
see the following reasons:

1) blk-mq core can deal with shared-tags case well via blk_mq_get_driver_tag(),
which can wake up queues waiting for driver tag.

2) SCSI is a bit special because it may return BLK_STS_RESOURCE if queue,
target or host is ready, but SCSI built-in restart can cover all these well,
see scsi_end_request(), queue will be rerun after any request initiated from
this host/target is completed.

In my test on scsi_debug(8 luns), this patch may improve IOPS by 20% ~ 30%
when running I/O on these 8 luns concurrently.

Fixes: 705cda97 ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reported-by: Andrew Jones <drjones@redhat.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Now hctx->lock is only acquired when adding hctx->dispatch_wait to
one wait queue, but not held when removing it from the wait queue.

IO hang can be observed easily if SCHED RESTART is disabled, that means
now RESTART exits just for fixing the issue in blk_mq_mark_tag_wait().

This patch fixes the issue by introducing hctx->dispatch_wait_lock and
holding it for removing hctx->dispatch_wait in blk_mq_dispatch_wake(),
since we need to avoid acquiring hctx->lock in irq context.

Fixes: eb619fdb ("blk-mq: fix issue with shared tag queue re-running")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

'hctx' won't be changed at all, so not necessary to pass
'**hctx' to blk_mq_mark_tag_wait().

Cc: Christoph Hellwig <hch@lst.de>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We never pass 'wait' as true to blk_mq_get_driver_tag(), and hence
we never change '**hctx' as well. The last use of these went away
with the flush cleanup, commit 0c2a6fe4.

So cleanup the usage and remove the two extra parameters.

Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Tested-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

The actual goal of the function bfq_bfqq_may_idle is to tell whether
it is better to perform device idling (more precisely: I/O-dispatch
plugging) for the input bfq_queue, either to boost throughput or to
preserve service guarantees. This commit improves the name of the
function accordingly.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>