Some chips have a fifo overflow bit issue where the bit is always
set. The result is that every data is dropped.

Change fifo overflow management by checking fifo count against
a maximum value.

Add fifo size in chip hardware set of values.

Fixes: f5057e7b ("iio: imu: inv_mpu6050: better fifo overflow handling")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The measured time value in the driver is limited to the maximum distance
which can be read by the sensor. This limitation was wrong and is fixed
by this patch.

It also takes into account that we are supporting a variety of sensors
today and that the recently added sensors have a higher maximum
distance range.

Changes in v2:
- Added a Tested-by
Suggested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Tested-by: Zbyněk Kocur <zbynek.kocur@fel.cvut.cz>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc:<Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

It could happen that either `val` or `val2` [provided from userspace] is
negative. In that case the computed frequency could get a weird value.

Fix this by checking that neither of the 2 variables is negative, and check
that the computed result is not-zero.

Fixes: e4f95939 ("iio: imu: adis16480 switch sampling frequency attr to core support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First set of IIO fixes for the 5.4 cycle.

* adis16400
  - Make sure to free memory on a few failure paths.
* adxl372
  - Fix wrong fifo depth
  - Fix wrong indexing of data from the fifo.
  - Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
  - This is a fix for a fix.  The original fix made sure we kept the
    configuration from some firmwares to preserve a bias current.
    Unfortunately it appears the previous behaviour was working around
    a buggy firmware by overwriting the wrong value it had.  Hence
    a regression was seen.
* bmc150
  - Fix the centre temperature.  This was due to an error in one of the
    datasheets.
* hx711
  - Fix an issue where a badly timed interrupt could lead to a control
    line being high long enough to put the device into a low power state.
* meson_sar_adc
  - Fix a case where the irq was enabled before everything it uses was
    allocated.
* st_lsm6dsx
  - Ensure we don't set the sensor sensitivity to 0 as it will force
    all readings to 0.
  - Fix a wait time for the slave i2c controller when the accelerometer
    is not enabled.
* stm32-adc
  - Precursor for fix. Move a set of register definitions to a header.
  - Fix a race when several ADCs are in use with some using interrupts
    to control the dataflow and some using DMA.
* vcnl4000
  - Fix a garbage of_match_table in which a string was passed instead
    of the intended enum.

* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: Fix an undefied reference error in noa1305_probe
  iio: light: opt3001: fix mutex unlock race
  iio: adc: ad799x: fix probe error handling
  iio: light: add missing vcnl4040 of_compatible
  iio: light: fix vcnl4000 devicetree hooks
  iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
  iio: adc: axp288: Override TS pin bias current for some models
  iio: imu: adis16400: fix memory leak
  iio: imu: adis16400: release allocated memory on failure
  iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
  iio: adc: stm32-adc: move registers definitions
  iio: accel: adxl372: Perform a reset at start up
  iio: accel: adxl372: Fix push to buffers lost samples
  iio: accel: adxl372: Fix/remove limitation for FIFO samples
  iio: adc: hx711: fix bug in sampling of data
  iio: fix center temperature of bmc150-accel-core
  iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
  iio: adc: meson_saradc: Fix memory allocation order

I hit the following error when compile the kernel.

drivers/iio/light/noa1305.o: In function `noa1305_probe':
noa1305.c:(.text+0x65): undefined reference to `__devm_regmap_init_i2c'
make: *** [vmlinux] Error 1
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b1 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since commit 0f7ddcc1 ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.

Fixes: 0f7ddcc1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Commit 5a441aad ("iio: light: vcnl4000 add support for the VCNL4040
proximity and light sensor") added the support for the vcnl4040 but
forgot to add the of_compatible. Fix this by adding it now.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Fixes: 5a441aad ("iio: light: vcnl4000 add support for the VCNL4040 proximity and light sensor")
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since commit ebd457d5 ("iio: light: vcnl4000 add devicetree hooks")
the of_match_table is supported but the data shouldn't be a string.
Instead it shall be one of 'enum vcnl4000_device_ids'. Also the matching
logic for the vcnl4020 was wrong. Since the data retrieve mechanism is
still based on the i2c_device_id no failures did appeared till now.

Fixes: ebd457d5 ("iio: light: vcnl4000 add devicetree hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Angus Ainslie (Purism) angus@akkea.ca
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout

Fixes: c91c1c84 ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since commit 9bcf15f7 ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot.  This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.

In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).

Fixes: 9bcf15f7 ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In adis_update_scan_mode_burst, if adis->buffer allocation fails release
the adis->xfer.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
  called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
  request instead. It's then automatically cleared by DMA read. But the
  handler gets called due to status bit is temporarily set (IRQ triggered
  by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).

Fixes: 2763ea05 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq

It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.

Fixes: 2763ea05 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We need to perform a reset a start up to make sure that the chip is in a
consistent state. This reset also disables all the interrupts which
should only be enabled together with the iio buffer. Not doing this, was
sometimes causing unwanted interrupts to trigger.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce3 ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

One in two sample sets was lost by multiplying fifo_set_size with
sizeof(u16). Also, the double number of available samples were pushed to
the iio buffers.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce3 ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Currently, the driver sets the FIFO_SAMPLES register with the number of
sample sets (maximum of 170 for 3 axis data, 256 for 2-axis and 512 for
single axis). However, the FIFO_SAMPLES register should store the number
of samples, regardless of how the FIFO format is configured.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Fixes: f4f55ce3 ("iio:adxl372: Add FIFO and interrupts support")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.

Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.

This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.

Fixes: c3b2fdd0 ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In vt6655_probe, if vnt_init() fails the cleanup code needs to be called
like other error handling cases. The call to device_free_info() is
added.

Fixes: 67013f2c ("staging: vt6655: mac80211 conversion add main mac80211 functions")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191004200319.22394-1-navid.emamdoost@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix mount failed "Cannot allocate memory".

When the memory gets fragmented, kzalloc() might fail to allocate
physically contiguous pages for the struct exfat_sb_info (its size is
about 34KiB) even the total free memory is enough.
Use kvzalloc() to solve this problem.
Reviewed-by: Ethan Wu <ethanwu@synology.com>
Signed-off-by: Jia-Ye Li <jiayeli@synology.com>
Link: https://lore.kernel.org/r/20190925083729.4653-1-jiayeli@synology.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In fbtft_framebuffer_alloc the error handling path should take care of
releasing frame buffer after it is allocated via framebuffer_alloc, too.
Therefore, in two failure cases the goto destination is changed to
address this issue.

Fixes: c296d5f9 ("staging: fbtft: core support")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190930030949.28615-1-navid.emamdoost@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Speakup exposes a set of sysfs attributes under
/sys/accessibility/speakup/ for user-space to interact with and
configure speakup's kernel modules. This patch describes those
attributes. Some attributes either lack a description or contain
incomplete description. They are marked wit TODO.
Authored-by: Gregory Nowak <greg@gregn.net>
Submitted-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Link: https://lore.kernel.org/r/20191001214729.1770-1-okash.khawaja@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's incorrect to compare HighestRate with 0x0b twice in the following
manner "if (HighestRate > 0x0b) ... else if (HighestRate > 0x0b) ...". The
"else if" branch is constantly false. The second comparision should be
with 0x03 according to the max_rate_idx in ODM_RAInfo_Init().

Cc: Michael Straube <straube.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20190926073138.12109-1-efremov@linux.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If kzalloc() returns NULL, the error path doesn't stop the flow of
control from entering rtw_hal_read_chip_version() which dereferences the
null pointer. Fix this by adding a 'goto' to the error path to more
gracefully handle the issue and avoid proceeding with initialization
steps that we're no longer prepared to handle.

Also update the debug message to be more consistent with the other debug
messages in this function.

Addresses-Coverity: ("Dereference after null check")
Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com>
Link: https://lore.kernel.org/r/20190927214415.899-1-connor.kuehl@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The PCM draining behavior got broken since the recent refactoring, and
this turned out to be the incorrect expectation of the firmware
behavior regarding "draining".  While I expected the "drain" flag at
the stop operation would do processing the queued samples, it seems
rather dropping the samples.

As a quick fix, just drop the SNDRV_PCM_INFO_DRAIN_TRIGGER flag, so
that the driver uses the normal PCM draining procedure.  Also, put
some caution comment to the function for future readers not to fall
into the same pitfall.

Fixes: d7ca3a71 ("staging: bcm2835-audio: Operate non-atomic PCM ops")
BugLink: https://github.com/raspberrypi/linux/issues/2983
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20190914152405.7416-1-tiwai@suse.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

flexfb was an attempt to write a generic fbtft driver that was abandoned.
All the displays it supports are supported by other fbtft drivers.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20190917171843.10334-3-noralf@tronnes.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit c440eee1 ("Staging: fbtft: Switch to the gpio descriptor
interface") removed the gpio code from fbtft_device rendering it useless.

fbtft_device is a module that was used on the Raspberry Pi to dynamically
add fbtft devices when the Pi didn't have Device Tree support.
Just remove the module since it's the responsibility of Device Tree, ACPI
or platform code to add devices.

Fixes: c440eee1 ("Staging: fbtft: Switch to the gpio descriptor interface")
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20190917171843.10334-2-noralf@tronnes.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit c440eee1 ("Staging: fbtft: Switch to the gpio descriptor
interface") removed setting gpios via platform data. This means that
fbtft will now only work with Device Tree so set the dependency.

This also prevents a NULL pointer deref on non-DT platform because
fbtftops.request_gpios is not set in that case anymore.

Fixes: c440eee1 ("Staging: fbtft: Switch to the gpio descriptor interface")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20190917171843.10334-1-noralf@tronnes.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On 32-bit:

    In file included from drivers/staging/octeon/octeon-ethernet.h:41,
		     from drivers/staging/octeon/ethernet-tx.c:25:
    drivers/staging/octeon/octeon-stubs.h: In function ‘cvmx_phys_to_ptr’:
    drivers/staging/octeon/octeon-stubs.h:1205:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
      return (void *)(physical_address);
	     ^
    drivers/staging/octeon/ethernet-tx.c: In function ‘cvm_oct_xmit’:
    drivers/staging/octeon/ethernet-tx.c:264:37: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
       hw_buffer.s.addr = XKPHYS_TO_PHYS((u64)skb->data);
					 ^
    drivers/staging/octeon/octeon-stubs.h:2:30: note: in definition of macro ‘XKPHYS_TO_PHYS’
     #define XKPHYS_TO_PHYS(p)   (p)
				  ^
    drivers/staging/octeon/ethernet-tx.c:268:37: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
       hw_buffer.s.addr = XKPHYS_TO_PHYS((u64)skb->data);
					 ^
    drivers/staging/octeon/octeon-stubs.h:2:30: note: in definition of macro ‘XKPHYS_TO_PHYS’
     #define XKPHYS_TO_PHYS(p)   (p)
				  ^
    drivers/staging/octeon/ethernet-tx.c:276:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
	 XKPHYS_TO_PHYS((u64)skb_frag_address(fs));
			^
    drivers/staging/octeon/octeon-stubs.h:2:30: note: in definition of macro ‘XKPHYS_TO_PHYS’
     #define XKPHYS_TO_PHYS(p)   (p)
				  ^
    drivers/staging/octeon/ethernet-tx.c:280:37: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
       hw_buffer.s.addr = XKPHYS_TO_PHYS((u64)CVM_OCT_SKB_CB(skb));
					 ^
    drivers/staging/octeon/octeon-stubs.h:2:30: note: in definition of macro ‘XKPHYS_TO_PHYS’
     #define XKPHYS_TO_PHYS(p)   (p)
				  ^

Fix this by replacing casts to "u64" by casts to "uintptr_t", which is
either 32-bit or 64-bit, and adding an intermediate cast to "uintptr_t"
where needed.

Exposed by commit 171a9bae ("staging/octeon: Allow test build on
!MIPS").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20190919095022.29099-1-geert@linux-m68k.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix a spelling typo in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Link: https://lore.kernel.org/r/20190930130504.21994-1-standby24x7@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The copyright notices as I got them said "GPLv2 or later", which I
screwed up when putting in the SPDX tags.  Fix them to match the
license I got the code under.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>

Link: https://lore.kernel.org/r/122590.1568853488@turing-policeSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add SPDX identifier to Kconfig.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20190917190755.21723-1-straube.linux@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>