- 05 Feb, 2013 40 commits
-
-
Sean Young authored
A sample resolution of 2us generates more than 300 interrupts per key and this resolution is not needed unless carrier reports are enabled. Revert to a resolution of 10us unless carrier reports are needed. This generates up to a fifth of the interrupts. Signed-off-by:
Sean Young <sean@mess.org> Acked-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Lad, Prabhakar authored
Without this patch the adv7343 encoder was being set to default configuration which caused display not to work on this board. This patch passes the necessary platform data required for adv7343 encoder to work on da850 evm. Signed-off-by:
Lad, Prabhakar <prabhakar.lad@ti.com> Acked-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Lad, Prabhakar authored
The current code was implemented with some default configurations, this default configuration works on board and doesn't work on other. This patch accepts the configuration through platform data and configures the encoder depending on the data passed. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Two fixes: - the priv field wasn't set to 0. - only V4L2_FIELD_INTERLACED is supported. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
- add device_caps support - fix bus_info - fix numerous tuner-related problems due to incorrect tests and setting v4l2_tuner fields to wrong values. - remove (audio) input support from the radio: it doesn't belong there. This also fixed a nasty issue where opening the radio would set dev->input to 5 for no good reason. This was never set back to a valid TV input after closing the radio device, thus leaving it at 5 which is out of bounds of the vinput card array. Signed-off-by:
-
Hans Verkuil authored
Convert the meye driver to the control framework. Some private controls have been replaced with standardized controls (SHARPNESS and JPEGQUAL). The AGC control looks like it can be replaced by the AUTOGAIN control, but it isn't a boolean so I do not know how to interpret it. The FRAMERATE control looks like it can be replaced by S_PARM, but again, without knowing how to interpret it I decided to leave it alone. Signed-off-by:
-
Hans Verkuil authored
If you only poll for events, then vb2_poll will return POLLPRI | POLLERR if no streaming is in progress. That's not right, it's perfectly valid to poll just for events. Cc: Pawel Osciak <pawel@osciak.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Hans Verkuil authored
These are already done elsewhere. Signed-off-by:
-
Hans Verkuil authored
I know, nobody really cares about this black-and-white webcam anymore, but it was fun to do. Tested with an actual webcam. Signed-off-by:
-
Hans Verkuil authored
Fix a v4l2-compliance problem: the priv field of v4l2_pix_format must be cleared by drivers. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
- instead of a mute module option, use audmode as per the spec. - clamp the frequency before setting it. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Such ioctls are not valid for radio devices. Signed-off-by:
-
Hans Verkuil authored
Don't set version (done by the v4l2 core), fill in bus_info, set correct driver name and add device_caps support. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
The inputmask for the tea6420 wasn't set and the wrong mute register value was used. Signed-off-by:
-
Hans Verkuil authored
The balance control did not do what it is supposed to do due to wrong calculations. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Hans Verkuil authored
When the control IDs were split off from videodev2.h to v4l2-controls.h these new Digital Video controls were forgotten (the two patches may have crossed one another). Move these controls to their proper place in v4l2-controls.h. Signed-off-by:
-
Sylwester Nawrocki authored
Newer Exynos4 SoC are equipped with a local camera ISP that controls external raw image sensor directly. Such sensors can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to the ISP, which then feeds image data to the FIMCn IP. Thus there can be two busses associated with an image source (sensor). Rename struct s5p_fimc_isp_info describing external image sensor (video decoder) to struct fimc_source_info to avoid confusion. bus_type is split into fimc_bus_type and sensor_bus_type. The bus type enumeration is extended to include both FIMC Writeback input types. The bus_type enumeration and the data structure name in the board files are modified according to the above changes. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Andrzej Hajda authored
Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Signed-off-by:
-
Sachin Kamat authored
devm_regulator_bulk_get saves some cleanup and exit code. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sylwester Nawrocki authored
Add clk_prepare(), clk_unprepare() calls for the sclk_cam clocks to ensure the driver works on platforms with the common clocks API enabled. Signed-off-by:
-
Sylwester Nawrocki authored
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection targets are not supposed to be handled in the set_selection ioctl. Remove the code that doesn't do anything sensible now and make sure ctx->state is modified with the spinlock held. Signed-off-by:
-
Sylwester Nawrocki authored
Make sure a valid image format is initially set on both the CAPTURE and the OUTPUT buffer queue. Signed-off-by:
-
Sylwester Nawrocki authored
With presence of some faults, e.g. caused by wrong platform data or the device tree structure the IDX_SENSOR entry in the array may be NULL, so make sure it is not dereferenced then. Signed-off-by:
-
Sachin Kamat authored
Fixes the following sparse warnings: drivers/media/i2c/s5c73m3/s5c73m3-core.c:42:5: warning: symbol 'boot_from_rom' was not declared. Should it be static? drivers/media/i2c/s5c73m3/s5c73m3-core.c:45:5: warning: symbol 'update_fw' was not declared. Should it be static? drivers/media/i2c/s5c73m3/s5c73m3-core.c:298:5: warning: symbol 's5c73m3_isp_comm_result' was not declared. Should it be static? Signed-off-by:
-
Sylwester Nawrocki authored
clk_set_rate(), clk_enable() functions can fail, so check the return values to avoid surprises. While at it use ERR_PTR() value to indicate an invalid clock. Signed-off-by:
-
Sylwester Nawrocki authored
clk_set_rate(), clk_enable() functions can fail, so check the return values to avoid surprises. While at it use ERR_PTR() value to indicate an invalid clock. Signed-off-by:
-
Sylwester Nawrocki authored
The previous method of registering platform entities into the main driver using driver_find() and then iterating over devices bound to a driver was racy and is being removed here. Nothing was preventing module from unloading during a call to try_module_get(driver->owner). Instead, we look up a device first and then check for its driver while holding device lock. The platform sub-devices are looked up and registered to the top level driver. When any sub-device is not yet initialized and ready the main driver's probe() will be deferred. Signed-off-by:
-
Sylwester Nawrocki authored
Add missing line breaks in the debug traces. Signed-off-by:
-
Sachin Kamat authored
devm_regulator_bulk_get is device managed and saves some cleanup and exit code. Signed-off-by:
-
Sylwester Nawrocki authored
This patch fixes regression introduced in commit 6319d6a002beb26631 '[media] fimc-lite: Add ISP FIFO output support'. In case of a configuration where video is captured at the video node exposed by the FIMC-LITE driver there is a following video pipeline: sensor -> MIPI-CSIS.n -> FIMC-LITE.n subdev -> FIMC-LITE.n video node In this situation s_stream() handler of the FIMC-LITE.n is called back from within VIDIOC_STREAMON/OFF ioctl of the FIMC-LITE.n video node, through vb2_stream_on/off(), start/stop_streaming and fimc_pipeline_call(set_stream). The fimc->lock mutex is already held then, before invoking vidioc_streamon/off. So it must not be taken again in the s_stream() callback in this case, to avoid a deadlock. This patch makes fimc->out_path atomic_t so the mutex don't need to be taken in the FIMC-LITE subdev s_stream() callback in the DMA output case. Signed-off-by:
-
Sylwester Nawrocki authored
The .s_power FIMC-LITE subdev callback is now empty and unneeded. The FIMC-LITE IP power handling will be done by the FIMC-IS driver, so just remove the callback. Signed-off-by:
-
