[ Upstream commit 70a87287 ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

https://bugzilla.kernel.org/show_bug.cgi?id=206283Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 457bfc0a ]

As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1d3ca681 ]

When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 73d527ae ]

Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 22e98449 ]

Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b0b03951 ]

Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9583a363 ]

Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 78f7a756 ]

The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().

The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".

There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.

However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.

Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.

Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d6bce213 ]

The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().

The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.

That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.

Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:

	// read the rid length field
	bap_read(ai, pBuf, 2, BAP1);
	// length for remaining part of rid
	len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
	...
	// read remainder of the rid
	rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);

PC4500_readrid() then returns to readrids() which does:

	len = comp->len;
	if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {

Where comp->len is the user controlled length field.

So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.

Fix it by kzalloc()'ing the buffer.

Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9e0caab8 ]

The optee driver uses specific page table types to verify if a memory
region is normal. These types are not defined in nommu systems. Trying
to compile the driver in these systems results in a build error:

  linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’:
  linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared
     (first use in this function); did you mean ‘PREEMPT_MASK’?
     return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
                             ^~~~~~~~~~~~~
                             PREEMPT_MASK
  linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is
     reported only once for each function it appears in
  linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared
     (first use in this function)
     return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
                                            ^~~~~~~~~~~~~~~~~~~

Make the optee driver depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[jw: update commit title]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6849b5eb ]

Updates to the Generic Timer architecture allow ID_PFR1.GenTimer to
have values other than 0 or 1 while still preserving backward
compatibility. At the moment, Linux is quite strict in the way it
handles this field at early boot and will not configure arch timer if
it doesn't find the value 1.

Since here use ubfx for arch timer version extraction (hyb-stub build
with -march=armv7-a, so it is safe)

To help backports (even though the code was correct at the time of writing)

Fixes: 8ec58be9 ("ARM: virt: arch_timers: enable access to physical timers")
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0e220962 ]

When a link is going down the driver will be calling fnic_cleanup_io(),
which will traverse all commands and calling 'done' for each found command.
While the traversal is handled under the host_lock, calling 'done' happens
after the host_lock is being dropped.

As fnic_queuecommand_lck() is being called with the host_lock held, it
might well be that it will pick the command being selected for abortion
from the above routine and enqueue it for sending, but then 'done' is being
called on that very command from the above routine.

Which of course confuses the hell out of the scsi midlayer.

So fix this by not queueing commands when fnic_cleanup_io is active.

Link: https://lore.kernel.org/r/20200116102053.62755-1-hare@suse.deSigned-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8aaea2b0 ]

When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f042365d ]

With an ebpf program that redirects packets through a xfrm interface,
packets are dropped because no dst is attached to skb.

This could also be reproduced with an AF_PACKET socket, with the following
python script (xfrm1 is a xfrm interface):

 import socket
 send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0)
 # scapy
 # p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request')
 # raw(p)
 req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00'
 send_s.sendto(req, ('xfrm1', 0x800, 0, 0))

It was also not possible to send an ip packet through an AF_PACKET socket
because a LL header was expected. Let's remove those LL header constraints.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 95224166 ]

With an ebpf program that redirects packets through a vti[6] interface,
the packets are dropped because no dst is attached.

This could also be reproduced with an AF_PACKET socket, with the following
python script (vti1 is an ip_vti interface):

 import socket
 send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0)
 # scapy
 # p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request')
 # raw(p)
 req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00'
 send_s.sendto(req, ('vti1', 0x800, 0, 0))
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5abd45ea ]

BeagleBone Black series is equipped with 512MB RAM
whereas only 256MB is included from am335x-bone-common.dtsi

This leads to an issue with unusual setups when devicetree
is loaded by GRUB2 directly.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2763bba6 ]

When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 95f4d9cc ]

Temporary files used in the VDSO build process linger on even after make
mrproper: vdso-dummy.o.tmp, vdso.so.dbg.tmp.

Delete them once they're no longer needed.
Signed-off-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6fc7caa8 ]

Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8f1880cb ]

With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.

Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9ec22d7c ]

Fixes: af308b94 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e1611965 ]

After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:

In function 'iw_handler_get_iwstats',
    inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
    inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
    inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
    inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
   memcpy(extra, stats, sizeof(struct iw_statistics));
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here

The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.

Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.deSigned-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6f601265 ]

TKIP replay protection was skipped for the very first frame received
after a new key is configured. While this is potentially needed to avoid
dropping a frame in some cases, this does leave a window for replay
attacks with group-addressed frames at the station side. Any earlier
frame sent by the AP using the same key would be accepted as a valid
frame and the internal RSC would then be updated to the TSC from that
frame. This would allow multiple previously transmitted group-addressed
frames to be replayed until the next valid new group-addressed frame
from the AP is received by the station.

Fix this by limiting the no-replay-protection exception to apply only
for the case where TSC=0, i.e., when this is for the very first frame
protected using the new key, and the local RSC had not been set to a
higher value when configuring the key (which may happen with GTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20200107153545.10934-1-j@w1.fiSigned-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 26ec17a1 ]

In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.

If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.

If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.

To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c4b9d655 ]

Commit e33e2241 ("Revert "cfg80211: Use 5MHz bandwidth by
default when checking usable channels"") fixed a broken
regulatory (leaving channel 12 open for AP where not permitted).
Apply a similar fix to custom regulatory domain processing.
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Link: https://lore.kernel.org/r/1576836859-8945-1-git-send-email-ganapathi.bhat@nxp.com
[reword commit message, fix coding style, add a comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4f80b70e ]

resource_size_t should be printed with its own size-independent format
to fix warnings when compiling on 64-bit platform (e.g. with
COMPILE_TEST):

    arch/parisc/kernel/drivers.c: In function 'print_parisc_device':
    arch/parisc/kernel/drivers.c:892:9: warning:
        format '%p' expects argument of type 'void *',
        but argument 4 has type 'resource_size_t {aka unsigned int}' [-Wformat=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a9ff44f0 ]

RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce780a47 ]

Change mutex and spinlock management to avoid sleep
in atomic issue.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20200113100400.30472-1-arnaud.pouliquen@st.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1f27dbd8 ]

Allow the user to configure the fan to turn on / speed-up at lower
thresholds then before (20 degrees Celcius as minimum instead of 40) and
likewise also allow the user to delay the fan speeding-up till the
temperature hits 90 degrees Celcius (was 70).

Cc: Jason Anderson <jasona.594@gmail.com>
Reported-by: Jason Anderson <jasona.594@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5365ec1a ]

Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.

Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.

Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4fad78ad ]

This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.

The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit aa604651 ]

Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.

Fixes: 46ec20ff ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 89b71b3f ]

The rt5640->jack is NULL if jack is already disabled at the time of
driver's module unloading.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200106014707.11378-1-digetx@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8bea5ac0 ]

Determined empirically, no documentation is available.

The OLPC XO-1.75 laptop used parent 1, that one being VCTCXO/4 (65MHz), but
thought it's a VCTCXO/2 (130MHz). The mmp2 timer driver, not knowing
what is going on, ended up just dividing the rate as of
commit f36797ee ("ARM: mmp/mmp2: dt: enable the clock")'

Link: https://lore.kernel.org/r/20191218190454.420358-3-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 02a61449 ]

The following warning is triggered every time an unestablished mesh peer
gets dumped. Checks if a peer link is established before retrieving the
airtime link metric.

[ 9563.022567] WARNING: CPU: 0 PID: 6287 at net/mac80211/mesh_hwmp.c:345
               airtime_link_metric_get+0xa2/0xb0 [mac80211]
[ 9563.022697] Hardware name: PC Engines apu2/apu2, BIOS v4.10.0.3
[ 9563.022756] RIP: 0010:airtime_link_metric_get+0xa2/0xb0 [mac80211]
[ 9563.022838] Call Trace:
[ 9563.022897]  sta_set_sinfo+0x936/0xa10 [mac80211]
[ 9563.022964]  ieee80211_dump_station+0x6d/0x90 [mac80211]
[ 9563.023062]  nl80211_dump_station+0x154/0x2a0 [cfg80211]
[ 9563.023120]  netlink_dump+0x17b/0x370
[ 9563.023130]  netlink_recvmsg+0x2a4/0x480
[ 9563.023140]  ____sys_recvmsg+0xa6/0x160
[ 9563.023154]  ___sys_recvmsg+0x93/0xe0
[ 9563.023169]  __sys_recvmsg+0x7e/0xd0
[ 9563.023210]  do_syscall_64+0x4e/0x140
[ 9563.023217]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20191203180644.70653-1-markus.theil@tu-ilmenau.de
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0c545240 ]

According to the BSP source code, both the AR100 and R_APB2 clocks have
PLL_PERIPH0 as mux index 3, not 2 as it was on previous chips. The pre-
divider used for PLL_PERIPH0 should be changed to index 3 to match.

This was verified by running a rough benchmark on the AR100 with various
clock settings:

        | mux | pre-divider | iterations/second | clock source |
        |=====|=============|===================|==============|
        |   0 |           0 |  19033   (stable) |       osc24M |
        |   2 |           5 |  11466 (unstable) |  iosc/osc16M |
        |   2 |          17 |  11422 (unstable) |  iosc/osc16M |
        |   3 |           5 |  85338   (stable) |  pll-periph0 |
        |   3 |          17 |  27167   (stable) |  pll-periph0 |

The relative performance numbers all match up (with pll-periph0 running
at its default 600MHz).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 463f550f ]

It has been reported by Google that rseq is not behaving properly
with respect to clone when CLONE_VM is used without CLONE_THREAD.

It keeps the prior thread's rseq TLS registered when the TLS of the
thread has moved, so the kernel can corrupt the TLS of the parent.

The approach of clearing the per task-struct rseq registration
on clone with CLONE_THREAD flag is incomplete. It does not cover
the use-case of clone with CLONE_VM set, but without CLONE_THREAD.

Here is the rationale for unregistering rseq on clone with CLONE_VM
flag set:

1) CLONE_THREAD requires CLONE_SIGHAND, which requires CLONE_VM to be
   set. Therefore, just checking for CLONE_VM covers all CLONE_THREAD
   uses. There is no point in checking for both CLONE_THREAD and
   CLONE_VM,

2) There is the possibility of an unlikely scenario where CLONE_SETTLS
   is used without CLONE_VM. In order to be an issue, it would require
   that the rseq TLS is in a shared memory area.

   I do not plan on adding CLONE_SETTLS to the set of clone flags which
   unregister RSEQ, because it would require that we also unregister RSEQ
   on set_thread_area(2) and arch_prctl(2) ARCH_SET_FS for completeness.
   So rather than doing a partial solution, it appears better to let
   user-space explicitly perform rseq unregistration across clone if
   needed in scenarios where CLONE_VM is not set.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191211161713.4490-3-mathieu.desnoyers@efficios.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f84ae29a ]

It is necessary to call free_arg(arg) when add_filter_type() returns NULL
in filter_event().
Signed-off-by: Hewenliang <hewenliang4@huawei.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Link: http://lore.kernel.org/lkml/20191209063549.59941-1-hewenliang4@huawei.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 03729cfa ]

Any user of wkup_m3_ipc calls wkup_m3_ipc_get to get a handle and this
checks the value of the static variable m3_ipc_state to see if the
wkup_m3 is ready. Currently this is populated during probe before
rproc_boot has been called, meaning there is a window of time that
wkup_m3_ipc_get can return a valid handle but the wkup_m3 itself is not
ready, leading to invalid IPC calls to the wkup_m3 and system
instability.

To avoid this, move the population of the m3_ipc_state variable until
after rproc_boot has succeeded to guarantee a valid and usable handle
is always returned.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e17e7c49 ]

On am57xx-beagle-x15, 5V0 is connected to P16, P17, P18 and P19
connectors. On am57xx-evm, 5V0 regulator is used to get 3V6 regulator
which is connected to the COMQ port. Model 5V0 regulator here in order
for it to be used in am57xx-evm to model 3V6 regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>