- 11 Jun, 2019 33 commits
-
-
Mauro Carvalho Chehab authored
commit a4768663 upstream. Most Siano devices require an alignment for the response. Changeset f3be52b0056a ("media: usb: siano: Fix general protection fault in smsusb") changed the logic with gets such aligment, but it now produces a sparce warning: drivers/media/usb/siano/smsusb.c: In function 'smsusb_init_device': drivers/media/usb/siano/smsusb.c:447:37: warning: 'in_maxp' may be used uninitialized in this function [-Wmaybe-uninitialized] 447 | dev->response_alignment = in_maxp - sizeof(struct sms_msg_hdr); | ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~ The sparse message itself is bogus, but a broken (or fake) USB eeprom could produce a negative value for response_alignment. So, change the code in order to check if the result is not negative. Fixes: 31e0456d ("media: usb: siano: Fix general protection fault in smsusb") CC: <stable@vger.kernel.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alan Stern authored
commit 45457c01 upstream. GCC complains about an apparently uninitialized variable recently added to smsusb_init_device(). It's a false positive, but to silence the warning this patch adds a trivial initialization. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
kbuild test robot <lkp@intel.com> CC: <stable@vger.kernel.org> Signed-off-by:
-
Alan Stern authored
commit 31e0456d upstream. The syzkaller USB fuzzer found a general-protection-fault bug in the smsusb part of the Siano DVB driver. The fault occurs during probe because the driver assumes without checking that the device has both IN and OUT endpoints and the IN endpoint is ep1. By slightly rearranging the driver's initialization code, we can make the appropriate checks early on and thus avoid the problem. If the expected endpoints aren't present, the new code safely returns -ENODEV from the probe routine. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit e0feb734 upstream. If a disconnected device is closed, rio_close() must free the buffers. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 3864d339 upstream. This driver is using a global variable. It cannot handle more than one device at a time. The issue has been existing since the dawn of the driver. Signed-off-by:
-
Maximilian Luz authored
commit ea261113 upstream. Without USB_QUIRK_NO_LPM ethernet will not work and rtl8152 will complain with r8152 <device...>: Stop submitting intr, status -71 Adding the quirk resolves this. As the dock is externally powered, this should not have any drawbacks. Signed-off-by:
Maximilian Luz <luzmaximilian@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 9a5729f6 upstream. The pointer used to log a failure of usb_register_dev() must be set before the error is logged. v2: fix that minor is not available before registration Signed-off-by:
-
Alan Stern authored
commit a03ff544 upstream. The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the USB core, caused by a failure to check the actual size of a BOS descriptor. This patch adds a check to make sure the descriptor is at least as large as it is supposed to be, so that the code doesn't inadvertently access memory beyond the end of the allocated region when assigning to dev->bos->desc->bNumDeviceCaps later on. Signed-off-by:
-
Shuah Khan authored
commit 3ea3091f upstream. Fix the following sparse context imbalance regression introduced in a patch that fixed sleeping function called from invalid context bug. kbuild test robot reported on: tree/branch: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git usb-linus Regressions in current branch: drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476 Error ids grouped by kconfigs: recent_errors ├── i386-allmodconfig │ └── drivers-usb-usbip-stub_dev.c:second-lock-on-line ├── x86_64-allmodconfig │ ├── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_disconnect-different-lock-contexts-for-basic-block │ └── drivers-usb-usbip-stub_dev.c:sparse:sparse:context-imbalance-in-stub_probe-different-lock-contexts-for-basic-block └── x86_64-allyesconfig └── drivers-usb-usbip-stub_dev.c:second-lock-on-line This is a real problem in an error leg where spin_lock() is called on an already held lock. Fix the imbalance in stub_probe() and stub_disconnect(). Signed-off-by:
Shuah Khan <skhan@linuxfoundation.org> Fixes: 0c9e8b3c ("usbip: usbip_host: fix BUG: sleeping function called from invalid context") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Shuah Khan authored
commit 0c9e8b3c upstream. stub_probe() and stub_disconnect() call functions which could call sleeping function in invalid context whil holding busid_lock. Fix the problem by refining the lock holds to short critical sections to change the busid_priv fields. This fix restructures the code to limit the lock holds in stub_probe() and stub_disconnect(). stub_probe(): [15217.927028] BUG: sleeping function called from invalid context at mm/slab.h:418 [15217.927038] in_atomic(): 1, irqs_disabled(): 0, pid: 29087, name: usbip [15217.927044] 5 locks held by usbip/29087: [15217.927047] #0: 0000000091647f28 (sb_writers#6){....}, at: vfs_write+0x191/0x1c0 [15217.927062] #1: 000000008f9ba75b (&of->mutex){....}, at: kernfs_fop_write+0xf7/0x1b0 [15217.927072] #2: 00000000872e5b4b (&dev->mutex){....}, at: __device_driver_lock+0x3b/0x50 [15217.927082] #3: 00000000e74ececc (&dev->mutex){....}, at: __device_driver_lock+0x46/0x50 [15217.927090] #4: 00000000b20abbe0 (&(&busid_table[i].busid_lock)->rlock){....}, at: get_busid_priv+0x48/0x60 [usbip_host] [15217.927103] CPU: 3 PID: 29087 Comm: usbip Tainted: G W 5.1.0-rc6+ #40 [15217.927106] Hardware name: Dell Inc. OptiPlex 790/0HY9JP, BIOS A18 09/24/2013 [15217.927109] Call Trace: [15217.927118] dump_stack+0x63/0x85 [15217.927127] ___might_sleep+0xff/0x120 [15217.927133] __might_sleep+0x4a/0x80 [15217.927143] kmem_cache_alloc_trace+0x1aa/0x210 [15217.927156] stub_probe+0xe8/0x440 [usbip_host] [15217.927171] usb_probe_device+0x34/0x70 stub_disconnect(): [15279.182478] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908 [15279.182487] in_atomic(): 1, irqs_disabled(): 0, pid: 29114, name: usbip [15279.182492] 5 locks held by usbip/29114: [15279.182494] #0: 0000000091647f28 (sb_writers#6){....}, at: vfs_write+0x191/0x1c0 [15279.182506] #1: 00000000702cf0f3 (&of->mutex){....}, at: kernfs_fop_write+0xf7/0x1b0 [15279.182514] #2: 00000000872e5b4b (&dev->mutex){....}, at: __device_driver_lock+0x3b/0x50 [15279.182522] #3: 00000000e74ececc (&dev->mutex){....}, at: __device_driver_lock+0x46/0x50 [15279.182529] #4: 00000000b20abbe0 (&(&busid_table[i].busid_lock)->rlock){....}, at: get_busid_priv+0x48/0x60 [usbip_host] [15279.182541] CPU: 0 PID: 29114 Comm: usbip Tainted: G W 5.1.0-rc6+ #40 [15279.182543] Hardware name: Dell Inc. OptiPlex 790/0HY9JP, BIOS A18 09/24/2013 [15279.182546] Call Trace: [15279.182554] dump_stack+0x63/0x85 [15279.182561] ___might_sleep+0xff/0x120 [15279.182566] __might_sleep+0x4a/0x80 [15279.182574] __mutex_lock+0x55/0x950 [15279.182582] ? get_busid_priv+0x48/0x60 [usbip_host] [15279.182587] ? reacquire_held_locks+0xec/0x1a0 [15279.182591] ? get_busid_priv+0x48/0x60 [usbip_host] [15279.182597] ? find_held_lock+0x94/0xa0 [15279.182609] mutex_lock_nested+0x1b/0x20 [15279.182614] ? mutex_lock_nested+0x1b/0x20 [15279.182618] kernfs_remove_by_name_ns+0x2a/0x90 [15279.182625] sysfs_remove_file_ns+0x15/0x20 [15279.182629] device_remove_file+0x19/0x20 [15279.182634] stub_disconnect+0x6d/0x180 [usbip_host] [15279.182643] usb_unbind_device+0x27/0x60 Signed-off-by:
-
Carsten Schmid authored
commit 7aa1bb2f upstream. With defective USB sticks we see the following error happen: usb 1-3: new high-speed USB device number 6 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: device descriptor read/64, error -71 usb 1-3: new high-speed USB device number 7 using xhci_hcd usb 1-3: device descriptor read/64, error -71 usb 1-3: unable to get BOS descriptor set usb 1-3: New USB device found, idVendor=0781, idProduct=5581 usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 ... BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 This comes from the following place: [ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.222092] PGD 0 P4D 0 [ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P U W O 4.14.67-apl #1 [ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore] [ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000 [ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] [ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046 [ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002 [ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2 [ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001 [ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000 [ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000 [ 1660.499494] FS: 0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000 [ 1660.508530] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0 [ 1660.522917] Call Trace: [ 1660.525657] usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore] [ 1660.531792] usb_disable_device+0x242/0x260 [usbcore] [ 1660.537439] usb_disconnect+0xc1/0x2b0 [usbcore] [ 1660.542600] hub_event+0x596/0x18f0 [usbcore] [ 1660.547467] ? trace_preempt_on+0xdf/0x100 [ 1660.552040] ? process_one_work+0x1c1/0x410 [ 1660.556708] process_one_work+0x1d2/0x410 [ 1660.561184] ? preempt_count_add.part.3+0x21/0x60 [ 1660.566436] worker_thread+0x2d/0x3f0 [ 1660.570522] kthread+0x122/0x140 [ 1660.574123] ? process_one_work+0x410/0x410 [ 1660.578792] ? kthread_create_on_node+0x60/0x60 [ 1660.583849] ret_from_fork+0x3a/0x50 [ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00 [ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70 [ 1660.617921] CR2: 0000000000000008 Tracking this down shows that udev->bos is NULL in the following code: (xhci.c, in xhci_set_usb2_hardware_lpm) field = le32_to_cpu(udev->bos->ext_cap->bmAttributes); <<<<<<< here xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n", enable ? "enable" : "disable", port_num + 1); if (enable) { /* Host supports BESL timeout instead of HIRD */ if (udev->usb2_hw_lpm_besl_capable) { /* if device doesn't have a preferred BESL value use a * default one which works with mixed HIRD and BESL * systems. See XHCI_DEFAULT_BESL definition in xhci.h */ if ((field & USB_BESL_SUPPORT) && (field & USB_BESL_BASELINE_VALID)) hird = USB_GET_BESL_BASELINE(field); else hird = udev->l1_params.besl; The failing case is when disabling LPM. So it is sufficient to avoid access to udev->bos by moving the instruction into the "enable" clause. Cc: Stable <stable@vger.kernel.org> Signed-off-by:
Carsten Schmid <carsten_schmid@mentor.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Andrey Smirnov authored
commit f7fac17c upstream. Xhci_handshake() implements the algorithm already captured by readl_poll_timeout_atomic(). Convert the former to use the latter to avoid repetition. Turned out this patch also fixes a bug on the AMD Stoneyridge platform where usleep(1) sometimes takes over 10ms. This means a 5 second timeout can easily take over 15 seconds which will trigger the watchdog and reboot the system. [Add info about patch fixing a bug to commit message -Mathias] Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by:
Raul E Rangel <rrangel@chromium.org> Reviewed-by:
-
Fabio Estevam authored
commit c1a145a3 upstream. Commit 597c56e3 ("xhci: update bounce buffer with correct sg num") caused the following build warnings: drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=] Use %zu for printing size_t type in order to fix the warnings. Fixes: 597c56e3 ("xhci: update bounce buffer with correct sg num") Reported-by:
Fabio Estevam <festevam@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by:
-
Henry Lin authored
commit 597c56e3 upstream. This change fixes a data corruption issue occurred on USB hard disk for the case that bounce buffer is used during transferring data. While updating data between sg list and bounce buffer, current implementation passes mapped sg number (urb->num_mapped_sgs) to sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data not get copied if target buffer is located in the elements after mapped sg elements. This change passes sg number for full list to fix issue. Besides, for copying data from bounce buffer, calling dma_unmap_single() on the bounce buffer before copying data to sg list can avoid cache issue. Fixes: f9c589e1 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by:
Henry Lin <henryl@nvidia.com> Signed-off-by:
-
Rasmus Villemoes authored
commit ef4d6f6b upstream. The ror32 implementation (word >> shift) | (word << (32 - shift) has undefined behaviour if shift is outside the [1, 31] range. Similarly for the 64 bit variants. Most callers pass a compile-time constant (naturally in that range), but there's an UBSAN report that these may actually be called with a shift count of 0. Instead of special-casing that, we can make them DTRT for all values of shift while also avoiding UB. For some reason, this was already partly done for rol32 (which was well-defined for [0, 31]). gcc 8 recognizes these patterns as rotates, so for example __u32 rol32(__u32 word, unsigned int shift) { return (word << (shift & 31)) | (word >> ((-shift) & 31)); } compiles to 0000000000000020 <rol32>: 20: 89 f8 mov %edi,%eax 22: 89 f1 mov %esi,%ecx 24: d3 c0 rol %cl,%eax 26: c3 retq Older compilers unfortunately do not do as well, but this only affects the small minority of users that don't pass constants. Due to integer promotions, ro[lr]8 were already well-defined for shifts in [0, 8], and ro[lr]16 were mostly well-defined for shifts in [0, 16] (only mostly - u16 gets promoted to _signed_ int, so if bit 15 is set, word << 16 is undefined). For consistency, update those as well. Link: http://lkml.kernel.org/r/20190410211906.2190-1-linux@rasmusvillemoes.dkSigned-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Reported-by:
Ido Schimmel <idosch@mellanox.com> Tested-by:
Will Deacon <will.deacon@arm.com> Cc: Vadim Pasternak <vadimp@mellanox.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
James Clarke authored
commit d3c976c1 upstream. Previously, %g2 would end up with the value PAGE_SIZE, but after the commit mentioned below it ends up with the value 1 due to being reused for a different purpose. We need it to be PAGE_SIZE as we use it to step through pages in our demap loop, otherwise we set different flags in the low 12 bits of the address written to, thereby doing things other than a nucleus page flush. Fixes: a74ad5e6 ("sparc64: Handle extremely large kernel TLB range flushes more gracefully.") Reported-by:
Meelis Roos <mroos@linux.ee> Tested-by:
James Clarke <jrtc27@jrtc27.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Junwei Hu authored
commit 526f5b85 upstream. Error message printed: modprobe: ERROR: could not insert 'tipc': Address family not supported by protocol. when modprobe tipc after the following patch: switch order of device registration, commit 7e27e8d6 ("tipc: switch order of device registration to fix a crash") Because sock_create_kern(net, AF_TIPC, ...) called by tipc_topsrv_create_listener() in the initialization process of tipc_init_net(), so tipc_socket_init() must be execute before that. Meanwhile, tipc_net_id need to be initialized when sock_create() called, and tipc_socket_init() is no need to be called for each namespace. I add a variable tipc_topsrv_net_ops, and split the register_pernet_subsys() of tipc into two parts, and split tipc_socket_init() with initialization of pernet params. By the way, I fixed resources rollback error when tipc_bcast_init() failed in tipc_init_net(). Fixes: 7e27e8d6 ("tipc: switch order of device registration to fix a crash") Signed-off-by:
Junwei Hu <hujunwei4@huawei.com> Reported-by:
Wang Wang <wangwang2@huawei.com> Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com Reviewed-by:
Kang Zhou <zhoukang7@huawei.com> Reviewed-by:
Suanming Mou <mousuanming@huawei.com> Signed-off-by:
-
David S. Miller authored
commit 5593530e upstream. This reverts commit 532b0f7e. More revisions coming up. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 7681f31e upstream. There is no need for this at all. Worst it means that if the guest tries to write to BARs it could lead (on certain platforms) to PCI SERR errors. Please note that with af6fc858 "xen-pciback: limit guest control of command register" a guest is still allowed to enable those control bits (safely), but is not allowed to disable them and that therefore a well behaved frontend which enables things before using them will still function correctly. This is done via an write to the configuration register 0x4 which triggers on the backend side: command_write \- pci_enable_device \- pci_enable_device_flags \- do_pci_enable_device \- pcibios_enable_device \-pci_enable_resourcess [which enables the PCI_COMMAND_MEMORY|PCI_COMMAND_IO] However guests (and drivers) which don't do this could cause problems, including the security issues which XSA-120 sought to address. Reported-by:
Jan Beulich <jbeulich@suse.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Daniel Axtens authored
commit 357d065a upstream. VMX ghash was using a fallback that did not support interleaving simd and nosimd operations, leading to failures in the extended test suite. If I understood correctly, Eric's suggestion was to use the same data format that the generic code uses, allowing us to call into it with the same contexts. I wasn't able to get that to work - I think there's a very different key structure and data layout being used. So instead steal the arm64 approach and perform the fallback operations directly if required. Fixes: cc333cd6 ("crypto: vmx - Adding GHASH routines for VMX module") Cc: stable@vger.kernel.org # v4.1+ Reported-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Daniel Axtens <dja@axtens.net> Acked-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Tested-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Antoine Tenart authored
[ Upstream commit 21808437 ] MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but the current code is passing the global tx queue offset, so it ends up writing to unknown registers (between 0x8280 and 0x82fc, which seemed to be unused by the hardware). This fixes the issue by using the logical queue id instead. Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by:
Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by:
-
Jisheng Zhang authored
[ Upstream commit d484e06e ] Fix below issues in err code path of probe: 1. we don't need to unregister_netdev() because the netdev isn't registered. 2. when register_netdev() fails, we also need to destroy bm pool for HWBM case. Fixes: dc35a10f ("net: mvneta: bm: add support for hardware buffer management") Signed-off-by:
Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by:
-
Rasmus Villemoes authored
[ Upstream commit 84b3fd1f ] Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends up in bits 47:32 of the return value, instead of bits 31:16 as they should. Fixes: 6e46e2d8 ("net: dsa: mv88e6xxx: Fix u64 statistics") Signed-off-by:
Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by:
Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 903869bd ] ip_sf_list_clear_all() needs to be defined even if !CONFIG_IP_MULTICAST Fixes: 3580d04a ("ipv4/igmp: fix another memory leak in igmpv3_del_delrec()") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
-
Eric Dumazet authored
[ Upstream commit 3580d04a ] syzbot reported memory leaks [1] that I have back tracked to a missing cleanup from igmpv3_del_delrec() when (im->sfmode != MCAST_INCLUDE) Add ip_sf_list_clear_all() and kfree_pmc() helpers to explicitely handle the cleanups before freeing. [1] BUG: memory leak unreferenced object 0xffff888123e32b00 (size 64): comm "softirq", pid 0, jiffies 4294942968 (age 8.010s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 e0 00 00 01 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<000000006105011b>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<000000006105011b>] slab_post_alloc_hook mm/slab.h:439 [inline] [<000000006105011b>] slab_alloc mm/slab.c:3326 [inline] [<000000006105011b>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553 [<000000004bba8073>] kmalloc include/linux/slab.h:547 [inline] [<000000004bba8073>] kzalloc include/linux/slab.h:742 [inline] [<000000004bba8073>] ip_mc_add1_src net/ipv4/igmp.c:1961 [inline] [<000000004bba8073>] ip_mc_add_src+0x36b/0x400 net/ipv4/igmp.c:2085 [<00000000a46a65a0>] ip_mc_msfilter+0x22d/0x310 net/ipv4/igmp.c:2475 [<000000005956ca89>] do_ip_setsockopt.isra.0+0x1795/0x1930 net/ipv4/ip_sockglue.c:957 [<00000000848e2d2f>] ip_setsockopt+0x3b/0xb0 net/ipv4/ip_sockglue.c:1246 [<00000000b9db185c>] udp_setsockopt+0x4e/0x90 net/ipv4/udp.c:2616 [<000000003028e438>] sock_common_setsockopt+0x38/0x50 net/core/sock.c:3130 [<0000000015b65589>] __sys_setsockopt+0x98/0x120 net/socket.c:2078 [<00000000ac198ef0>] __do_sys_setsockopt net/socket.c:2089 [inline] [<00000000ac198ef0>] __se_sys_setsockopt net/socket.c:2086 [inline] [<00000000ac198ef0>] __x64_sys_setsockopt+0x26/0x30 net/socket.c:2086 [<000000000a770437>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<00000000d3adb93b>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 9c8bb163 ("igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Michael Chan authored
[ Upstream commit 296d5b54 ] For every RX packet, the driver replenishes all buffers used for that packet and puts them back into the RX ring and RX aggregation ring. In one code path where the RX packet has one RX buffer and one or more aggregation buffers, we missed recycling the aggregation buffer(s) if we are unable to allocate a new SKB buffer. This leads to the aggregation ring slowly running out of buffers over time. Fix it by properly recycling the aggregation buffers. Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.") Reported-by:
Rakesh Hemnani <rhemnani@fb.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Chris Packham authored
TLV_SET is called with a data pointer and a len parameter that tells us how many bytes are pointed to by data. When invoking memcpy() we need to careful to only copy len bytes. Previously we would copy TLV_LENGTH(len) bytes which would copy an extra 4 bytes past the end of the data pointer which newer GCC versions complain about. In file included from test.c:17: In function 'TLV_SET', inlined from 'test' at test.c:186:5: /usr/include/linux/tipc_config.h:317:3: warning: 'memcpy' forming offset [33, 36] is out of the bounds [0, 32] of object 'bearer_name' with type 'char[32]' [-Warray-bounds] memcpy(TLV_DATA(tlv_ptr), data, tlv_len); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ test.c: In function 'test': test.c::161:10: note: 'bearer_name' declared here char bearer_name[TIPC_MAX_BEARER_NAME]; ^~~~~~~~~~~ We still want to ensure any padding bytes at the end are initialised, do this with a explicit memset() rather than copy bytes past the end of data. Apply the same logic to TCM_SET. Signed-off-by:Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by:
-
Kloetzke Jan authored
[ Upstream commit ad70411a ] When disconnecting cdc_ncm the kernel sporadically crashes shortly after the disconnect: [ 57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000 ... [ 58.006653] PC is at 0x0 [ 58.009202] LR is at call_timer_fn+0xec/0x1b4 [ 58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145 [ 58.020976] sp : ffffff8008003da0 [ 58.024295] x29: ffffff8008003da0 x28: 0000000000000001 [ 58.029618] x27: 000000000000000a x26: 0000000000000100 [ 58.034941] x25: 0000000000000000 x24: ffffff8008003e68 [ 58.040263] x23: 0000000000000000 x22: 0000000000000000 [ 58.045587] x21: 0000000000000000 x20: ffffffc68fac1808 [ 58.050910] x19: 0000000000000100 x18: 0000000000000000 [ 58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10 [ 58.061556] x15: 0000000000000001 x14: 000000000000006e [ 58.066878] x13: 0000000000000000 x12: 00000000000000ba [ 58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020 [ 58.077524] x9 : 8000100008001000 x8 : 0000000000000001 [ 58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70 [ 58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b [ 58.093492] x3 : 0000000000000000 x2 : 0000000000000000 [ 58.098814] x1 : 0000000000000000 x0 : 0000000000000000 ... [ 58.205800] [< (null)>] (null) [ 58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c [ 58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128 [ 58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348 [ 58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc [ 58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac [ 58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac ... The crash happens roughly 125..130ms after the disconnect. This correlates with the 'delay' timer that is started on certain USB tx/rx errors in the URB completion handler. The problem is a race of usbnet_stop() with usbnet_start_xmit(). In usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in flight. This only makes sense if no new URBs are submitted concurrently, though. But the usbnet_start_xmit() can run at the same time on another CPU which almost unconditionally submits an URB. The error callback of the new URB will then schedule the timer after it was already stopped. The fix adds a check if the tx queue is stopped after the tx list lock has been taken. This should reliably prevent the submission of new URBs while usbnet_terminate_urbs() does its job. The same thing is done on the rx side even though it might be safe due to other flags that are checked there. Signed-off-by:
Jan Klötzke <Jan.Kloetzke@preh.de> Signed-off-by:
-
Jisheng Zhang authored
[ Upstream commit 49ce881c ] Commit 984203ce ("net: stmmac: mdio: remove reset gpio free") removed the reset gpio free, when the driver is unbinded or rmmod, we miss the gpio free. This patch uses managed API to request the reset gpio, so that the gpio could be freed properly. Fixes: 984203ce ("net: stmmac: mdio: remove reset gpio free") Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit a4270d67 ] If a network driver provides to napi_gro_frags() an skb with a page fragment of exactly 14 bytes, the call to gro_pull_from_frag0() will 'consume' the fragment by calling skb_frag_unref(skb, 0), and the page might be freed and reused. Reading eth->h_proto at the end of napi_frags_skb() might read mangled data, or crash under specific debugging features. BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline] BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 Read of size 2 at addr ffff88809366840c by task syz-executor599/8957 CPU: 1 PID: 8957 Comm: syz-executor599 Not tainted 5.2.0-rc1+ #32 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188 __kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 kasan_report+0x12/0x20 mm/kasan/common.c:614 __asan_report_load_n_noabort+0xf/0x20 mm/kasan/generic_report.c:142 napi_frags_skb net/core/dev.c:5833 [inline] napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841 tun_get_user+0x2f3c/0x3ff0 drivers/net/tun.c:1991 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2037 call_write_iter include/linux/fs.h:1872 [inline] do_iter_readv_writev+0x5f8/0x8f0 fs/read_write.c:693 do_iter_write fs/read_write.c:970 [inline] do_iter_write+0x184/0x610 fs/read_write.c:951 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1015 do_writev+0x15b/0x330 fs/read_write.c:1058 Fixes: a50e233c ("net-gro: restore frag0 optimization") Signed-off-by:
-
Andy Duan authored
[ Upstream commit ce8d24f9 ] Fix the clk mismatch in the error path "failed_reset" because below error path will disable clk_ahb and clk_ipg directly, it should use pm_runtime_put_noidle() instead of pm_runtime_put() to avoid to call runtime resume callback. Reported-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Tested-by:
-
Eric Dumazet authored
[ Upstream commit 8fb44d60 ] If llc_mac_hdr_init() returns an error, we must drop the skb since no llc_build_and_send_ui_pkt() caller will take care of this. BUG: memory leak unreferenced object 0xffff8881202b6800 (size 2048): comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.590s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 1a 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............ backtrace: [<00000000e25b5abe>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<00000000e25b5abe>] slab_post_alloc_hook mm/slab.h:439 [inline] [<00000000e25b5abe>] slab_alloc mm/slab.c:3326 [inline] [<00000000e25b5abe>] __do_kmalloc mm/slab.c:3658 [inline] [<00000000e25b5abe>] __kmalloc+0x161/0x2c0 mm/slab.c:3669 [<00000000a1ae188a>] kmalloc include/linux/slab.h:552 [inline] [<00000000a1ae188a>] sk_prot_alloc+0xd6/0x170 net/core/sock.c:1608 [<00000000ded25bbe>] sk_alloc+0x35/0x2f0 net/core/sock.c:1662 [<000000002ecae075>] llc_sk_alloc+0x35/0x170 net/llc/llc_conn.c:950 [<00000000551f7c47>] llc_ui_create+0x7b/0x140 net/llc/af_llc.c:173 [<0000000029027f0e>] __sock_create+0x164/0x250 net/socket.c:1430 [<000000008bdec225>] sock_create net/socket.c:1481 [inline] [<000000008bdec225>] __sys_socket+0x69/0x110 net/socket.c:1523 [<00000000b6439228>] __do_sys_socket net/socket.c:1532 [inline] [<00000000b6439228>] __se_sys_socket net/socket.c:1530 [inline] [<00000000b6439228>] __x64_sys_socket+0x1e/0x30 net/socket.c:1530 [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 BUG: memory leak unreferenced object 0xffff88811d750d00 (size 224): comm "syz-executor907", pid 7074, jiffies 4294943781 (age 8.600s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 f0 0c 24 81 88 ff ff 00 68 2b 20 81 88 ff ff ...$.....h+ .... backtrace: [<0000000053026172>] kmemleak_alloc_recursive include/linux/kmemleak.h:55 [inline] [<0000000053026172>] slab_post_alloc_hook mm/slab.h:439 [inline] [<0000000053026172>] slab_alloc_node mm/slab.c:3269 [inline] [<0000000053026172>] kmem_cache_alloc_node+0x153/0x2a0 mm/slab.c:3579 [<00000000fa8f3c30>] __alloc_skb+0x6e/0x210 net/core/skbuff.c:198 [<00000000d96fdafb>] alloc_skb include/linux/skbuff.h:1058 [inline] [<00000000d96fdafb>] alloc_skb_with_frags+0x5f/0x250 net/core/skbuff.c:5327 [<000000000a34a2e7>] sock_alloc_send_pskb+0x269/0x2a0 net/core/sock.c:2225 [<00000000ee39999b>] sock_alloc_send_skb+0x32/0x40 net/core/sock.c:2242 [<00000000e034d810>] llc_ui_sendmsg+0x10a/0x540 net/llc/af_llc.c:933 [<00000000c0bc8445>] sock_sendmsg_nosec net/socket.c:652 [inline] [<00000000c0bc8445>] sock_sendmsg+0x54/0x70 net/socket.c:671 [<000000003b687167>] __sys_sendto+0x148/0x1f0 net/socket.c:1964 [<00000000922d78d9>] __do_sys_sendto net/socket.c:1976 [inline] [<00000000922d78d9>] __se_sys_sendto net/socket.c:1972 [inline] [<00000000922d78d9>] __x64_sys_sendto+0x2a/0x30 net/socket.c:1972 [<00000000cec820c1>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:301 [<000000000c32554f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Mike Manning authored
[ Upstream commit 72f7cfab ] IPv6 does not consider if the socket is bound to a device when binding to an address. The result is that a socket can be bound to eth0 and then bound to the address of eth1. If the device is a VRF, the result is that a socket can only be bound to an address in the default VRF. Resolve by considering the device if sk_bound_dev_if is set. Signed-off-by:
Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Tested-by:
-
- 31 May, 2019 7 commits
-
-
Greg Kroah-Hartman authored
-
Chris Wilson authored
[ Upstream commit 60b80199 ] After an event is sent, we try to copy it into the user buffer of the first waiter in drm_read() and if the user buffer doesn't have enough room we put it back onto the list. However, we didn't wake up any subsequent waiter, so that event may sit on the list until either a new vblank event is sent or a new waiter appears. Rare, but in the worst case may lead to a stuck process. Testcase: igt/drm_read/short-buffer-wakeup Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170804082328.17173-1-chris@chris-wilson.co.ukSigned-off-by:
Sasha Levin <sashal@kernel.org>
-
Arnd Bergmann authored
[ Upstream commit 8ca51047 ] Building with clang shows a variable that is only used by the suspend/resume functions but defined outside of their #ifdef block: sound/soc/ti/davinci-mcasp.c:48:12: error: variable 'context_regs' is not needed and will not be emitted We commonly fix these by marking the PM functions as __maybe_unused, but here that would grow the davinci_mcasp structure, so instead add another #ifdef here. Fixes: 1cc0c054 ("ASoC: davinci-mcasp: Convert the context save/restore to use array") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Chris Lesiak authored
[ Upstream commit 5442dcaa ] This fixes a bug for messages containing both zero length and unidirectional xfers. The function spi_map_msg will allocate dummy tx and/or rx buffers for use with unidirectional transfers when the hardware can only do a bidirectional transfer. That dummy buffer will be used in place of a NULL buffer even when the xfer length is 0. Then in the function __spi_map_msg, if he hardware can dma, the zero length xfer will have spi_map_buf called on the dummy buffer. Eventually, __sg_alloc_table is called and returns -EINVAL because nents == 0. This fix prevents the error by not using the dummy buffer when the xfer length is zero. Signed-off-by:
Chris Lesiak <chris.lesiak@licor.com> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 26843bb1 ] While the sequencer is reset after each SPI message since commit 880c6d11 ("spi: rspi: Add support for Quad and Dual SPI Transfers on QSPI"), it was never reset for the first message, thus relying on reset state or bootloader settings. Fix this by initializing it explicitly during configuration. Fixes: 0b2182dd ("spi: add support for Renesas RSPI") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Aditya Pakki authored
[ Upstream commit f37d8e67 ] pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further, these buffers are used without a check. The patch checks for these failures and sends the error upstream. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
-
James Smart authored
[ Upstream commit c95a3b4b ] During debug, it was seen that the driver is issuing commands specific to SLI3 on SLI4 devices. Although the adapter correctly rejected the command, this should not be done. Revise the code to stop sending these commands on a SLI4 adapter. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
