'clocks' node is not a bus, but just a placeholder for clocks:

  apq8096-db820c.dtb: clocks: $nodename:0: 'clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
    From schema: dtschema/schemas/simple-bus.yaml
  apq8096-db820c.dtb: clocks: xo-board: {'compatible': ['fixed-clock'], '#clock-cells': [[0]],  ...
    From schema: dtschema/schemas/simple-bus.yaml
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324202244.744271-2-krzysztof.kozlowski@linaro.org

Add the final "s" to the pgio properties and fix the invalid "enable"
name to the correct "wake", checked against the HDK8450 schematics.

Fixes: bc6588bc ("arm64: dts: qcom: sm8450: add PCIe1 root device")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-4-0ca1bea1a843@linaro.org

Fixes the following DT bindings check error:
pci@1c00000: Unevaluated properties are not allowed ('power-domain-names' were unexpected)
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-3-0ca1bea1a843@linaro.org

Enable both touchpad nodes in the devictree and let the HID driver
determine which one is actually populated (by attempting to read from
each i2c address).

Ideally this would not be needed and the boot firmware should instead
enable only the node for the populated touchpad, but this is unlikely to
ever be realised for the X13s.

Note that the pin configuration must currently be moved to the parent
i2c-bus node even though only one of these nodes will ever be
successfully probed on a specific device (e.g. to allow them to be
probed in parallel).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324094744.20448-1-johan+linaro@kernel.org

The SPMI PMIC register region width is fixed and should not be encoded
in the devicetree.

Fixes: d6dbbda3 ("arm64: dts: qcom: sc8280xp-pmics: add pmk8280 sdam nvram")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230320135710.1989-3-johan+linaro@kernel.org

Add the Display Port controller subnode to the MDSS node.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-5-d78313cbc41d@linaro.org

The QMP PHY is a USB3/DP combo phy, switch to the newly
documented bindings and register the clocks to the GCC
and DISPCC controllers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-4-d78313cbc41d@linaro.org

Add the Display Port controller subnode to the MDSS node.

Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #SM8350-HDK
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-3-d78313cbc41d@linaro.org

The first QMP PHY is an USB3/DP combo phy, switch to the newly
documented bindings and register the clocks to the GCC
and DISPCC controllers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #SM8350-HDK
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230206-topic-sm8450-upstream-dp-controller-v6-2-d78313cbc41d@linaro.org

Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230217155838.848403-3-krzysztof.kozlowski@linaro.org

Bindings expect DBVDD-supply and LDO1-IN-supply:

  sc7280-herobrine-evoker-lte.dtb: codec@1a: 'DBVDD-supply' is a required property
  sc7280-herobrine-evoker-lte.dtb: codec@1a: 'LDO1-IN-supply' is a required property

In sc7180-trogdor.dtsi they come from the same regulator, so let's
assume intention was the same here.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230217155838.848403-2-krzysztof.kozlowski@linaro.org

It seems that the RT5682S codec does not use VBAT-supply:

  sc7180-trogdor-pazquel360-lte.dtb: codec@1a: Unevaluated properties are not allowed ('VBAT-supply' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230217155838.848403-1-krzysztof.kozlowski@linaro.org

Add the APCS, A53 PLL, cpu-opp-table nodes to bump the CPU frequency
above 800MHz.
Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230217083308.12017-6-quic_kathirav@quicinc.com

Describe the bus topology for PCIe domain 6 and add the ath11k
calibration variant so that the board file (calibration data) can be
loaded.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216246Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230321094011.9759-3-johan+linaro@kernel.org

All the input devices use s10b as 1.8V supply.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-7-johan+linaro@kernel.org

The s11b, s12b, s1c and bob supplies are used by several pmic
regulators. Add the missing description to the devicetree.

Note that there are still some consumers that are not (fully) described
in the devicetree so the supplies must remain marked as always-on for
now.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230322113318.17908-6-johan+linaro@kernel.org

Downstream DTS uses 16 mA drive strength for the WCD9385 audio codec
RESET_N reset pin.  It also pulls the pin down in shutdown mode, thus it
is more like a shutdown pin, not a reset.  Use the same settings here
for HDK8450 and keep the WCD9385 by default in powered off (so pin as
low).  Align the name of pin configuration node with other pins in the
DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308183317.559253-2-krzysztof.kozlowski@linaro.org

The HDK8450 uses WCD9385 audio codec, so use precise compatible, even
though WCD9380 and WCD9385 are both compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308183317.559253-1-krzysztof.kozlowski@linaro.org

Downstream DTS (and sc8280xp-lenovo-thinkpad-x13s with the same
speakers) uses 16 mA drive strength for the WSA8835 speaker SD_N
reset/shutdown pin.  Use the same for HDK8450, as it is seem the
recommended value.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308142712.277659-1-krzysztof.kozlowski@linaro.org

Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-8-3368473ec52d@linaro.org

Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-7-3368473ec52d@linaro.org

Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-6-3368473ec52d@linaro.org

Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-5-3368473ec52d@linaro.org

Add a SoC-specific compatbile to cpufreq_hw for compliancy with bindings.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-topic-cpufreq_bindings-v1-4-3368473ec52d@linaro.org

Enable the Hall effect sensor (flip cover) for OnePlus 6/6T.
The GPIO is mapped to SW_LID events as in msm8916, msm8994,
msm8998 devices.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306174147.185239-1-soyer@irl.hu

Remove trailing, redundant line breaks.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306081430.28491-2-krzysztof.kozlowski@linaro.org

Drop empty override of pm8998_gpios.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230306081430.28491-1-krzysztof.kozlowski@linaro.org

Bindings expect thermal node names to end with '-thermal', so fix pm660
and pm660l:

  sda660-inforce-ifc6560.dtb: thermal-zones: 'pm660', 'pm660l' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230305154308.241651-1-krzysztof.kozlowski@linaro.org

The "dr_mode" is a property of USB DWC3 node, not the Qualcomm wrapper
one:
  sm8350-microsoft-surface-duo2.dtb: usb@a6f8800: 'dr_mode' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+'

Fixes: c16160cf ("arm64: dts: qcom: add minimal DTS for Microsoft Surface Duo 2")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304130315.51595-2-krzysztof.kozlowski@linaro.org

Fix typo in USB DWC3 node maximum speed property.

Fixes: a41b6175 ("arm64: dts: qcom: sm8250: Add device tree for Xiaomi Mi Pad 5 Pro")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304130315.51595-1-krzysztof.kozlowski@linaro.org

Enable the high-speed UART port connected to the Bluetooth controller on
the sa8775p-adp development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-10-brgl@bgdev.pl

Enable the high-speed UART port connected to the GNSS controller on the
sa8775p-adp development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-9-brgl@bgdev.pl

Add two UART nodes that are known to be used by existing development
boards with this SoC.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-8-brgl@bgdev.pl

Enable the SPI interface exposed on the sa8775p-ride development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-7-brgl@bgdev.pl

Add the SPI controller node for the interface exposed on the sa8775p-ride
development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-6-brgl@bgdev.pl

This enables the I2C interface on the sa8775p-ride development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-5-brgl@bgdev.pl

Add a disabled node for the I2C interface that's exposed on the
sa8775p-ride development board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-4-brgl@bgdev.pl

Enable the second instance of the QUPv3 engine on the sa8775p-ride board.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-3-brgl@bgdev.pl

Add the second instance of the QUPv3 engine to the sa8775p.dtsi.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309103752.173541-2-brgl@bgdev.pl

Add a node describing the flash block found on pm8150l.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230321182319.24958-1-danila@jiaxyga.com