http://bugs.freedesktop.org/show_bug.cgi?id=20429Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[anholt: Massive cleanup of the slave addr function]
Signed-off-by: Eric Anholt <eric@anholt.net>

The general definition block contains the child device tables, which include
the SDVO device info. For example: device slave address, device dvo port,
device type.

We will get the info of SDVO device by parsing the general definition blocks.
Only when a valid slave address is found, it is regarded as the SDVO device.
And the info of DVO port and slave address is recorded.

http://bugs.freedesktop.org/show_bug.cgi?id=20429Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

This adds the register definitions for the display port enable register
along with those for the GMCH and Link M/N ratios required to drive display
port outputs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

We can safely assume that cursor addresses will not extend beyond the
addressable screen dimensions; setting the additional bits is harmless in
any case.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

We detect TV connect status by setting DAC voltage level override
values as 0.7 voltage for DAC_A/B/C. The corresponding 2-bits shold be 0x2,
In order correctly to set last bit as 0, at first we must clean it.

It fixed freedesktop.org bug #21204
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

This adds kernel mode setting on IGDNG with VGA output support.
Note that suspend/resume doesn't work yet.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Swizzle bit detection not working right on it.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[anholt: dropped drm_pciids.h hunk to avoid loading an incomplete driver]
Signed-off-by: Eric Anholt <eric@anholt.net>

Both desktop and mobile versions are added.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

keithp didn't like the original 20ms plan because a cooperative client could
be starved by an uncooperative client.  There may even have been problems
with cooperative clients versus cooperative clients.  So keithp changed
throttle to just wait for the second to last seqno emitted by that client.
It worked well, until we started getting more round-trips to the server
due to DRI2 -- the server throttles in BlockHandler, and so if you did more
than one round trip after finishing your frame, you'd end up unintentionally
syncing to the swap.

Fix this by keeping track of the client's requests, so the client can wait
when it has an outstanding request over 20ms old.  This should have
non-starving behavior, good behavior in the presence of restarts, and less
waiting.  Improves high-settings openarena performance on my GM45 by 50%.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This may fix cursor corruption in X on resume, which would persist until
the cursor was hidden and then shown again.

V2: Also include the cursor control regs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>

This could be triggered by a gtt mapping fault on 965 that decides to
remove the fence from another object that happens to be active currently.
Since the other object doesn't rely on the fence reg for its execution, we
don't wait for it to finish.  We'll soon be not waiting on 915 most of the
time as well, so just drop the BUG_ON.
Signed-off-by: Eric Anholt <eric@anholt.net>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/pmac: Update PowerMac 32-bit defconfig

Ideally we should have a directory of drivers and a link to the 'active'
driver. For now just show the first device which is effectively the existing
semantics without a warning.

This is an update on the original buggy patch that I then forgot to
resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels
fixed and submitted by Intel ...

Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This matches Bartlomiej's patch for ide_pci_generic:
c339dfdd

In the libata case netcell has its own mini driver. I suspect this fix is
actually only needed for some firmware revs but it does no harm either way.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup
  e1000: add missing length check to e1000 receive routine
  forcedeth: add phy_power_down parameter, leave phy powered up by default (v2)
  Bluetooth: Remove useless flush_work() causing lockdep warnings

* 'for-linus' of git://oss.sgi.com/xfs/xfs:
  xfs: prevent deadlock in xfs_qm_shake()
  xfs: fix overflow in xfs_growfs_data_private
  xfs: fix double unlock in xfs_swap_extents()

net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup

This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.

When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained.  After it's chained,
tc_ctl_tfilter() calls classifier's change().  When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.

In addition, cls_cgroup is initialized in change() not in init().  It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

	Patch to fix bad length checking in e1000.  E1000 by default does two
things:

1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put

Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set.  This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test).  If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb.  This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU.  The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000.  This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.

The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072).  Leaving the phy
powered on is the safest default behavior.  Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's possible to recurse into filesystem from the memory
allocation, which deadlocks in xfs_qm_shake(). Add check
for __GFP_FS, and bail out if it is not set.
Signed-off-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Hedi Berriche <hedi@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>

In the case where growing a filesystem would leave the last AG
too small, the fixup code has an overflow in the calculation
of the new size with one fewer ag, because "nagcount" is a 32
bit number.  If the new filesystem has > 2^32 blocks in it
this causes a problem resulting in an EINVAL return from growfs:

 # xfs_io -f -c "truncate 19998630180864" fsfile
 # mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile
 # mount -o loop fsfile /mnt
 # xfs_growfs /mnt

meta-data=/dev/loop0             isize=256    agcount=52,
agsize=76288719 blks
         =                       sectsz=512   attr=2
data     =                       bsize=4096   blocks=3905982455, imaxpct=5
         =                       sunit=0      swidth=0 blks
naming   =version 2              bsize=4096   ascii-ci=0
log      =internal               bsize=4096   blocks=32768, version=2
         =                       sectsz=512   sunit=0 blks, lazy-count=0
realtime =none                   extsz=4096   blocks=0, rtextents=0
xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument

Reported-by: richard.ems@cape-horn-eng.com
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>

Regreesion from commit ef8f7fc5, which rearranged the code in
xfs_swap_extents() leading to double unlock of xfs inode ilock.
That resulted in xfs_fsr deadlocking itself on platforms, which
don't handle double unlock of rw_semaphore nicely. It caused the
count go negative, which represents the write holder, without
really having one. ia64 is one of the platforms where deadlock
was easily reproduced and the fix was tested.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Felix Blyakher <felixb@sgi.com>

This mostly adds back AppleTouch support and adds CONFIG_HIGHMEM
by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: hash - Fix handling of sg entry that crosses page boundary

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Update documentation on fan_max
  hwmon: (lm78) Add missing __devexit_p()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix section attribute warnings.
  sparc64: Fix SET_PERSONALITY to not clip bits outside of PER_MASK.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  3c509: Add missing EISA IDs
  MAINTAINERS: take maintainership of the cpmac Ethernet driver
  net/firmare: Ignore .cis files
  ath1e: add new device id for asus hardware
  mlx4_en: Fix a kernel panic when waking tx queue
  rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle
  at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan
  mac8390: fix build with NET_POLL_CONTROLLER
  cxgb3: link fault fixes
  cxgb3: fix dma mapping regression
  netfilter: nfnetlink_log: fix wrong skbuff size	calculation
  netfilter: xt_hashlimit does a wrong SEQ_SKIP
  bfin_mac: fix build error due to net_device_ops convert
  atlx: move modinfo data from atlx.h to atl1.c
  gianfar: fix babbling rx error event bug
  cls_cgroup: read classid atomically in classifier
  netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache
  netfilter: nf_ct_tcp: fix accepting invalid RST segments

* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
  headers_check fix: linux/net_dropmon.h
  headers_check fix: linux/auto_fs.h

Add fan_max description.

Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

The remove function uses __devexit, so the .remove assignment needs
__devexit_p() to fix a build error with hotplug disabled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Several EISA device IDs for 3c509 family network cards are missing from 
the driver, making the cards unusable in their EISA mode.  Here's a fix to 
add them based on the EISA configuration files distributed by 3Com and our 
eisa.ids database.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds me as the maintainer of the CPMAC (AR7)
Ethernet driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>