- 13 Feb, 2014 20 commits
-
-
David S. Miller authored
Yuval Mintz says: ==================== bnx2x: Enhancements & semantic changes series This patch series contains several semantic (or mostly semantic) patches, as well as adding support for packet aggregations on the receive path of windows VMs and updating bnx2x to the new FW recently accepted upstream. Please consider applying these patches to `net-next'. (This is a repost as net-next was still closed when this was previously sent) ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Dmitry Kravkov authored
This new firmware fixes following bugs: 1. HW attention appears and traffic stops when iSCSI firmware tries to retransmit iSCSI login command when the iSCSI login is carrying data not aligned to 4-bytes. 2. FCoE traffic fails to run when running in switch-independent multi-function mode and there's more than one interface supporting FCoE on a given port. 3. While two ports are running FCoE with at least one of them has a function number (>1) on the same engine in a 4-port device a zeroed CQE is given, causing FCoE traffic to stop. Signed-off-by:Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by:
Ariel Elior <ariele@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
This removes the various points where the driver use bit operations in order to schedule the sp_rtnl_task from the code, adding a single utility function that does it instead. Signed-off-by:
-
Yuval Mintz authored
bnx2x_panic_dump() prints all kind of driver information, including slowpath information. Since VFs don't initialize slowpath information, a VF reaching this flow will likely cause a panic in the system as it will access NULL pointers. Signed-off-by:
-
Yuval Mintz authored
There are several places in IOV related flows where PF needs to determine whether a VF slowpath elements have already been configured (i.e., this affect its ability to configure/remove classifications for the VF). This patch changes the conditions for the validation and performs a cleaner validation (e.g., by replacing several validations with a single one). Signed-off-by:
-
Michal Kalderon authored
This provides PF-side support for VFs assigned to a VM running windows 2012 with the RSC feature enabled. Signed-off-by:
Michal Kalderon <michals@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
This is purely semantic - break the flow in which PF validates the VF classification filtering requirement is valid into several sub-functions for better readable code. Signed-off-by:
-
Ariel Elior authored
Latest FW performs this autonomously, makes this code surplus. Signed-off-by:
-
Yuval Mintz authored
Signed-off-by:
-
Yuval Mintz authored
There are some debug prints (mostly iov/statistics related) which clobber system logs whenever their verbosity level is set for an interface. This patch puts harsher verbosity requirements for such debug prints to be printed. Signed-off-by:
-
Florian Fainelli authored
Expose the PHY device has_fixups boolean as a sysfs property to help troubleshooting PHY configurations. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
Add a boolean property which indicates if the PHY has had any fixup routine ran on it. We are later going to use that boolean to expose it as a sysfs property to help troubleshooting. Signed-off-by:
-
Florian Fainelli authored
Expose the PHY device interface mode through sysfs since this is an useful piece of information for knowing how the attached networking device will have configured its transmit/receive path. Signed-off-by:
-
Florian Fainelli authored
of_get_phy_mode() uses a local array to map phy_interface_t values from include/linux/net/phy.h to a string which is read from the 'phy-mode' or 'phy-connection-type' property. In preparation for exposing the PHY interface mode through sysfs, perform the following: - mode phy_modes from drivers/of/of_net.c to include/linux/phy.h such that it is right below the phy_interface_t enum - make it a static inline function returning the string such that we can use it by just including include/linux/net/phy.h - add a PHY_INTERFACE_MODE_MAX enum value to guard the iteration in of_get_phy_mode() Signed-off-by:
-
Florian Fainelli authored
The comments above phy_{clear,config}_interrupt used the word "on" instead of "or", when talking about the return values of the functions, fix these two typos. Signed-off-by: -
Florian Fainelli authored
Some PHYs out there can be very quirky with respect to how they would report the auto-negotiation is completed. Allow drivers to override the generic aneg_done() implementation by providing their own. Since not all drivers have been updated yet to use genphy_aneg_done() as aneg_done() callback, we explicitely check that this callback is valid before calling into it. Signed-off-by:
-
Florian Fainelli authored
In preparation for allowing PHY drivers to potentially override their auto-negotiation done callback, move the contents of phy_aneg_done() to genphy_aneg_done() since that function really is the generic implementation based on the BMSR_ANEGCOMPLETE status. Signed-off-by:
-
Florian Fainelli authored
Use a convenience function: phy_speed_to_str() which will display human readable speeds. Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Florian Fainelli authored
Update phy_print_status() to also display the PHY device pause settings (rx/tx or off). Suggested-by:
-
Florian Fainelli authored
phy_print_status() currently uses dev_name(&phydev->dev) which will usually result in printing something along those lines for Device Tree aware drivers: libphy: f0b60000.etherne:0a - Link is Down libphy: f0ba0000.etherne:00 - Link is Up - 1000/Full This is not terribly useful for network administrators or users since we expect a network interface name to be able to correlate link events with interfaces. Update phy_print_status() to use netdev_info() with phydev->attached_dev which is the backing network device for our PHY device. The leading dash is removed since netdev_info() prefixes the messages with "<interface>: " already. Signed-off-by:
-
- 12 Feb, 2014 20 commits
-
-
David S. Miller authored
Shradha Shah says: ==================== Cleanup patches for the SFC driver This patch set consists of some cleanup and housekeeping patches for the sfc driver. These patches help to reduce the differences between the in- tree and out-of-tree driver. Ben Hutchings (12): sfc: Cache skb->data in local variable in efx_ptp_rx() sfc: Rewrite adjustment of PPS event in a clearer way sfc: Replace TSOH_OFFSET with the equivalent NET_IP_ALIGN sfc: Rename 'use_options' variable in tso_start() to clearer 'use_opt_desc' sfc: Remove unused definitions of EF10 user-mode DMA descriptors sfc: Correct comment about number of TX queues used on EF10 sfc: Preserve rx_frm_trunc counters when resizing DMA rings sfc: Use canonical pointer type for MAC address in efx_set_mac_address() sfc: Update product naming sfc: Cosmetic changes to self-test from the out-of-tree driver sfc: Fail self-test with -EBUSY, not -EIO, if the device is busy sfc: Add/remove blank lines to taste Laurence Evans (1): sfc: Removed adhoc scheme to rate limit PTP event queue overflow message ==================== Signed-off-by: -
Ben Hutchings authored
Remove trailing blank lines in several files. Use only one blank line between functions. Add a blank line as a separator in a few places. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
Shradha Shah <sshah@solarflare.com> Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
We don't use 'Solarstorm' or 'Solarflare Communications' in full any more. Signed-off-by:
-
Ben Hutchings authored
Functions such as is_valid_ether_addr() expect u8 *, so use that instead of char *. Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
We allocate efx_channel structures with kzalloc() so we don't need to zero-initialise individual fields in efx_probe_channel(). Further, this function will be called again during DMA ring resizing and we should not reset any statistics then. Signed-off-by:
-
Ben Hutchings authored
EF10 implements option descriptors to switch TX checksum offload on and off between packets. We could therefore use a single hardware TX queue per kernel TX queue, although we don't yet. Signed-off-by:
-
Ben Hutchings authored
These DMA descriptor types will only be used by the userland networking stack. Signed-off-by:
-
Ben Hutchings authored
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN will be defined as 0, so this macro is redundant. Signed-off-by:
-
Ben Hutchings authored
There is substantial latency in generation and handling of PPS events from the NIC, which we have to correct for before passing a host timestamp to the PPS subsystem. We compare clocks with the MC, giving us two offsets to subtract from the timestamp generated by pps_get_ts(): (a) Time from the last good sync (where we got host and NIC timestamps for nearly the same instant) to the time we called pps_get_ts() (b) Time from NIC top of second to the last good sync We currently calculate (a) + (b) in a quite confusing way. Instead, calculate (a) completely, then add (b) to it. Signed-off-by: -
Ben Hutchings authored
Signed-off-by:
-
Laurence Evans authored
Use conventional net_ratelimit() instead. Signed-off-by:
-
David S. Miller authored
Ben Hutchings says: ==================== ethtool: Improve documentation This series converts most comments in <linux/ethtool.h> into kernel-doc format, and expands them to describe the semantics as well as I understand them. It also fixes some kernel-doc formatting errors. I started on this at Solarflare, but they graciously allowed me to take it away and finish it off. ==================== Signed-off-by: -
Ben Hutchings authored
A colon almost unavoidably starts a new section. The script should be changed to provide a way to avoid this, but for now reword the comments to avoid using colons. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
The kernel-doc script does not tolerate the macro definition in between. Signed-off-by:
-
Ben Hutchings authored
Various ethtool command structures are declared with zero-length array at the end which are intended to be variable-length in userland (relying on lack of compiler bounds checking). However, in the kernel the structure and array are always allocated and passed to driver operations separately. Make that explicit. Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
Ben Hutchings authored
Signed-off-by:
-
