There is no need to do endpoint header removal in the ISR.
Also, this is needed when TX slot management is added later on.
Use a helper function to strip the driver header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A new routine that takes an endpoint explicitly is
introduced. The normal htc_send() now retrieves the endpoint
from the packet's private data. This would be useful
in TX completion when the endpoint ID would be required.
While at it, use a helper function to map the queue to endpoint.

Data/mgmt/beacon packets use htc_send(), while WMI comamnds
pass the endpoint to HTC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Handle queue start/stop properly by maintaining
a counter to check if the pending frame count has
exceeded the threshold. Otherwise, packets would be
dropped needlessly. While at it, use a simple flag
to track queue status and use helper functions too.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using a single URB for receiving WMI events is
insufficient, increase it to 64 to not lose
WMI events in high throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This event will be generated by the target for packet completions.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add a new cookie field that would be filled by the host.
This can be used to match the TX status WMI event with
the appropriate packet.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current max queue length of 1024 is quite large
and unnecessary. 256 suffices well enough even for high
throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For all packets sent through the USB_WLAN_TX_PIPE endpoint,
the private area of the SKB's tx_info can be used to store
driver-specific information. For packets sent through USB_REG_OUT_PIPE,
this will not make a difference since they are routed through a
separate routine that doesn't access the private region.

This would help in situations where TX information is required
in the URB callback.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WMI_TGT_TXQ_ENABLE_CMDID
WMI_HOST_ATTACH
WMI_DEBUG_INFO_CMDID
WMI_BEACON_UPDATE_CMDID
WMI_RESET_CMDID
WMI_RX_LINK_CMDID
WMI_STOP_DMA_RECV_CMDID
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.

Fix this by adjusting the beacon response time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, ampdu stream is created on the first qos packet to an
HT sta. The overhead of setting up the BA session may not be
justified if the outgoing packet rate is minimal (e.g., ping). So
we only allow ampdu streams after seeing a critical number of
packets in an arbitrary one-second interval.

Based on work by Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This makes it easier to handle moving stations to VLAN interfaces that are
part of a different bridge.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.

Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.

As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We do not need to enable all the interrupts in mwl8k_probe_hw.
We need to enable only MWL8K_A2H_INT_OPC_DONE interrupt for sending
commands to the firmware. Keep the other interrupts masked in
mwl8k_probe_hw. Also, in mwl8k_start, where we expect other interrupts,
enable only those interrupts we are interested in.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adds USB IDs for seven previously missing devices. Additionally, all
instances of 'Conceptronic' have been replaced by the OEM name.

Devices added are..
0411:01a2 - Buffalo WLI-UC-GNM, RT3070V
0586:341e - ZyXEL NWD2105, RT3070
13b1:002f - Linksys AE1000, RT3572
13b1:0031 - Cisco / Linksys AM10, RT3072
14b2:3c2c - Keebox W150NU / Alpha Networks WUS-N12, RT3070
157e:3013 - TRENDnet TEW-645UB, RT2770+RT2720
15a9:0012 - Airlink AWLL7025 / Gemtek WUBR-208N, RT2870+RT2850
Signed-off-by: Mark Davis <marked86@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes random disconnect.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver rtl8192ce does not initialize the LED correctly.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Check whether index is within bounds before testing the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>