Adds support for HSCIF0 and HSCIF1 on the r8a7790.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

While recasting commit 52421914 (ARM: shmobile:
R8A7778: add Ether support), I made a typo in the platform device's name: used
underscore instead of hyphen.

However, there's now patch merged to net-next.git renaming the platform device
from "sh-eth" to "r8a777x-ehter", so it makes the most sense to change the name
straight to that one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

While recasting commit dace48d0 (ARM: shmobile:
R8A7779: add Ether support), I made a typo in the platform device's name: used
underscore instead of hyphen.

However, there's now patch merged to net-next.git renaming the platform device
from "sh-eth" to "r8a777x-ehter", so it makes the most sense to change the name
straight to that one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

According to the datasheet, it is not allowed to change div4 clock rates
if an earlier rate change operation is still in progress, as indicated by
a set kick bit.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

An earlier commit "ARM: shmobile: sh73a0: add support for adjusting CPU
frequency" intended to replace some clock operations only for the Z-clock,
instead it replaced them for all div4 clocks, since all div4 clocks share
the same copy of clock operations. Fix this by using a separate clock
operations structure for Z-clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Break out the function sh73a0_init_delay() that now
gets called both for the C version of the code and
the DT -reference boards. This way we handle both
cases in the same way.

Allows us to boot with TWD only in the kernel configuration
for C board code. TWD is not yet enabled in the case of
DT -reference - this due to a dependency on CCF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables the use of the generic cpufreq-cpu0 driver on sh73a0.
Providing a regulator, a list of OPPs in DT, combined with a virtual
cpufreq-cpu0 platform device and a clock, attached to it is everything,
the cpufreq-cpu0 driver needs. The first sh73a0 platform, implementing
such CPUFreq support is kzm9g-reference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

On SH73A0 the output of PLL0 is supplied to two dividers, feeding clock to
the CPU core and SGX. Lower CPU frequencies allow the use of lower supply
voltages and thus reduce power consumption.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control SD*/MMC* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control SD* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a7790.
This patch adds it, and, set its parent/ratio via MD pin.
It is based on v0.05 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds SDHI register function which needs id number (= 0/1/2)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car M1 has many clocks, and it is possible to
read/use clock ratio of these clocks from FRQMRx.
But, these ratio are fixed value and
these are decided by MD pin status.

This patch reads MD pin status,
and used fixed ratio clock for other clocks.
It was tesed on bock-w board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PLL clocks are basis clock for other clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a73a4.
This patch adds it, and, set parent clock via CKSCR register.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add clock association for i2c0 and i2c1 for the new DT names.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When we use the ethernet device via DT setup, we need to add it
to a lookup list until this is properly handled later in a DT-only
fashion.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Ether setup code position was scattering.
This patch fixes it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SH_CLK_SET_RATIO() will be trouble without this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Convert code to use DEFINE_RES_MEM*() macros.
These macros were already used in this file,
this change makes their usage consistent throughout the file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct model name is R-Car M1A or R8A77781; R8A77780 corresponds to R-Car
M1S which is a SH based SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: manually applied]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.

To avoid further similar issues, also define the main_clks as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Merge tag 'stable/for-linus-3.10-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen fixes from Konrad Rzeszutek Wilk:
 - Regression fix in xen privcmd fixing a memory leak.
 - Add Documentation for tmem driver.
 - Simplify and remove code in the tmem driver.
 - Cleanups.

* tag 'stable/for-linus-3.10-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: Fixed assignment error in if statement
  xen/xenbus: Fixed over 80 character limit issue
  xen/xenbus: Fixed indentation error in switch case
  xen/tmem: Don't use self[ballooning|shrinking] if frontswap is off.
  xen/tmem: Remove the usage of '[no|]selfballoon' and use 'tmem.selfballooning' bool instead.
  xen/tmem: Remove the usage of 'noselfshrink' and use 'tmem.selfshrink' bool instead.
  xen/tmem: Remove the boot options and fold them in the tmem.X parameters.
  xen/tmem: s/disable_// and change the logic.
  xen/tmem: Fix compile warning.
  xen/tmem: Split out the different module/boot options.
  xen/tmem: Move all of the boot and module parameters to the top of the file.
  xen/tmem: Cleanup. Remove the parts that say temporary.
  xen/privcmd: fix condition in privcmd_close()

Pull hwmon fixes from Guenter Roeck:

 - Error path fixes for abituguru and iio_hwmon drivers.

 - Drop erroneously created attributes from nct6775 driver.

 - Drop redundant safety on cache lifetime for tmp401 driver.

 - Add explicit maintainer for LM95234 and TMP401 drivers.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  MAINTAINERS: Add myself as maintainer for LM95234 and TMP401 drivers
  hwmon: (tmp401) Drop redundant safety on cache lifetime
  hwmon: fix error return code in abituguru_probe()
  hwmon: (iio_hwmon) Fix null pointer dereference
  hwmon: (nct6775) Do not create non-existing attributes
  hwmon: (iio_hwmon) Fix missing iio_channel_release_all call if devm_kzalloc fail

In commit 78d77df7 ("x86-64, init: Do not set NX bits on non-NX
capable hardware") we added the early_pmd_flags that gets the NX bit set
when a CPU supports NX. However, the new variable was marked __initdata,
because the main _use_ of this is in an __init routine.

However, the bit setting happens from secondary_startup_64(), which is
called not only at bootup, but on every secondary CPU start.  Including
resuming from STR and at CPU hotplug time.  So the value cannot be
__initdata.
Reported-bisected-and-tested-by: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org # v3.9
Acked-by: Peter Anvin <hpa@linux.intel.com>
Cc: Fernando Luis Vázquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixed assignment error in if statement in balloon.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Fixed the format length of the xenbus_backend_ioctl()
function to meet the 80 character limit in
xenbus_dev_backend.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Fixed the indentation error in the switch case in
xenbus_dev_backend.c
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Merge tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:

 - Three fixes to make the boot path for device tree work properly on
   the Nomadik pin controller.

 - Compile warning fix for the vt8500 driver.

 - Fix error path in pinctrl-single.

 - Free mappings in error path of the Lantiq controller.

 - Documentation fixes.

* tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl/lantiq: Free mapping configs for both pin and groups
  pinctrl: single: fix error return code in pcs_parse_one_pinctrl_entry()
  pinctrl: generic: Fix typos and clarify comments
  pinctrl: vt8500: Fix incorrect data in WM8750 pinctrl table
  pinctrl: abx500: Rejiggle platform data and DT initialisation
  pinctrl: abx500: Specify failed sub-driver by ID instead of driver_data

Pull kbuild fix from Michal Marek:
 "In an attempt to improve make rpm-pkg, I broke make binrpm-pkg"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  package: Makefile: unbreak binrpm-pkg target

I wrote the LM95234 driver and extended the TMP401 driver substantially,
and I have hardware to test both, so it makes sense to explicitly
maintain them.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>